AIR FORCE A-A-59879-2010 TRUCK SHORT WHEEL BASE FIRE FIGHTING (STRUCTURAL 4x2)《短轴距消防车(结构 4x2)》.pdf

《AIR FORCE A-A-59879-2010 TRUCK SHORT WHEEL BASE FIRE FIGHTING (STRUCTURAL 4x2)《短轴距消防车(结构 4x2)》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-59879-2010 TRUCK SHORT WHEEL BASE FIRE FIGHTING (STRUCTURAL 4x2)《短轴距消防车(结构 4x2)》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: WR-ALC 542 CSW/CBSSS, 295 Byron Street, Robins AFB, GA 31098-1611. Since contact information can change, you may want to verify the currency of this address

2、 information using the ASSIST Online database at https:/assist.daps.dla.mil/online . FSC 4210 INCH-POUND A-A-59879 17 NOV 2010 COMMERCIAL ITEM DESCRIPTION TRUCK, SHORT WHEEL BASE, FIRE FIGHTING (STRUCTURAL, 4x2) The General Services Administration has authorized the use of this commercial item descr

3、iption for all federal agencies. 1. SCOPE. This commercial item description (CID) covers a short wheel based structural pumper truck. It has a 4x2 chassis; a diesel engine and automatic transmission; a cab to accommodate at least six seated persons with at least four doors; a 1,250 gallon per minute

4、 (gpm) fire pump; a 300 gallon minimum capacity water tank; utility equipment compartments; and fire hose. The structural pumper truck is intended to combat structural, wildland urban interface, and similar type fires. 2. SALIENT CHARACTERISTICS. The structural pumper truck shall be in accordance wi

5、th the applicable requirements of the following chapters of National Fire Protection Agency 1901, Standard for Automotive Fire Apparatus (Current Edition) as follows: Chapter Title 1 Administration 2 Referenced Publications 4 General Requirements 5 Pumper Fire Apparatus 12 Chassis and Vehicle Compon

6、ents 13 Low-Voltage Electrical Systems and Warning Devices 14 Driving and Crew Area 15 Body, Compartments, and Equipment Mounting 16 Fire Pump and Associated Equipment 19 Water Tanks 21 Foam Proportioning Systems 22 Compressed Air Foam Systems 23 Line Voltage Electrical Systems 25 Air Systems 2.1 Ad

7、ministration. 2.1.1 Environmental conditions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59879 2 2.1.1.1 Altitude. Unless otherwise specified (see 6.2.a), the vehicle, including the pumping system, shall be designed for operation at 2,000 fe

8、et above sea level. 2.1.1.2 Temperature range. The pumper shall be capable of satisfactory storage and operation in temperatures ranging from 0 to 125F. The pumper shall be equipped with a winterization system that extends the operational range of the pumper. The winterization system shall protect t

9、he agent pump, agent piping systems, firefighting systems, and water tank to 0F. It shall also include the vehicle engine oil and coolant systems. While in operation, the appropriate systems requiring winterization shall be powered by the pumper. While in storage, the winterization system shall be p

10、owered through the electrical shoreline connection (see 2.10.2). 2.1.2 Foreign object damage. All loose metal parts, such as pins and valve caps, shall be securely attached to the vehicle with wire ropes or chains. “Dog tag“ style beaded chains shall not be provided. Removable panels, if provided, s

11、hall be attached with captive fasteners. 2.1.3 Roadability. 2.1.3.1 Operating terrain. The 4x2 vehicle shall operate on paved and graded gravel roads. 2.1.3.2 Acceleration. The fully loaded vehicle shall accelerate from 0 to 35 miles per hour (mph) within 25 seconds on a level, paved road. 2.1.3.3 M

12、inimum speed. The fully loaded vehicle shall attain a minimum top speed of 50 mph on a level, paved road. 2.1.3.4 Gradeability. The fully loaded vehicle shall be able to maintain a speed of at least 20 mph while ascending any paved slope up to and including 6.0 percent. The fully loaded vehicle shal

13、l also be able to maintain a speed of at least 5 mph while ascending any paved slope up to and including 30 percent. 2.1.4 Overall dimensions. Overall dimensions shall be the minimum consistent with the operational performance and the design constraints necessary to achieve the specified performance

14、. Overall dimensions shall not exceed: Length 360 inches Width 96 inches (excluding mirrors) Height 120 inches 2.1.5 Turning diameter. The fully loaded pumper shall have a wall to wall turning diameter not to exceed 52 feet in both directions. 2.1.6 Angles of approach and departure. The fully loaded

15、 vehicle shall have angles of approach and departure of not less than 12.0. 2.1.7 Vehicle stability. Vehicle shall comply with roll over stability criteria as defined by NFPA 1901, paragraph 4.13. 2.1.8 Manuals. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

16、m IHS-,-,-A-A-59879 3 2.1.8.1 Technical manuals. The overall format for the manuals may be military specification, commercial, or a combination of both. Each technical manual shall have a title page. a. The contractor shall validate the technical manuals for accuracy prior to submission to the procu

17、ring activity for verification. The contractor shall submit one complete set to the procuring activity for verification 30 days before the first production inspection. Any changes or corrections noted by the procuring activity shall be corrected and updated pages or manuals shall be submitted to the

18、 procuring activity. b. Once approved by the procuring activity, the contractor shall pack two complete sets of technical manuals with each vehicle. An additional two complete sets shall be submitted to the procuring activity for stock. c. Once approved by the procuring activity and a Technical Orde

19、r number is assigned, the contractor shall pack two complete sets of both hard copy and CDs with each vehicle and one complete set of both hard copy and CDs shall be submitted to the procuring activity for stock. The procuring activitys address will be provided. d. The contractor shall grant the Uni

20、ted States Air Force a non-exclusive, non-assignable, royalty free U.S. Government (Government) Purpose License, to scan into CENTRA (the USAF repository) and to reproduce and distribute (either electronically or via hard medium) copies or facsimiles of manuals produced and distributed by the contra

21、ctor for this CID. These rights extend to Government agencies only, and the data contained in the technical manuals is not to be sold, disclosed or otherwise provided to any other entity or entities outside the Government. The license shall remain in effect as long as the vehicles described in the r

22、equired technical manuals remain under Government control and usage. In addition, the contractor shall grant permission for the Government to place an Air Force TO (Technical Order) number and publication date as well as distribution, warning, handling and destruction statements on the cover/title p

23、ages of the TO. 2.1.8.1.1 Operators manuals. The operators manual shall include all information required for the safe and efficient operation of the vehicle, including the fire extinguishing equipment, and any special attachments or auxiliary equipment. The operators manual shall include at least th

24、e following: a. Location and function of all controls and instruments shall be illustrated and fully described. b. Safety information that is consistent with the safety standards established by the Occupational Safety and Health Administration (OSHA). c. Checks and adjustments in preparation for pla

25、cing the vehicle for service upon receipt from the contractor. d. Preparation for shipment or storage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59879 4 e. Warranty information and period of the warranty for the complete vehicle and for any

26、 component warranty that exceeds the warranty of the complete vehicle. Addresses and telephone numbers shall be provided for all warranty providers. f. General description of and step-by-step instructions for the operation of the vehicle and its fire extinguishing system(s) and auxiliary equipment.

27、g. Description of the post-operational procedures (draining, flushing, et cetera). h. Checklists for the daily maintenance inspection and mission readiness checks that the operator is expected to perform. i. Procedures for towing a disabled vehicle. j. Schedules for required preventative maintenance

28、 and required periodic maintenance. 2.1.8.1.2 Service manuals. The service manual shall identify any special tools and test equipment required and shall cover troubleshooting and maintenance as well as minor and major repair procedures. The text shall contain performance specifications, tolerances,

29、and fluid capacities; current, voltage, and resistance data; test procedures; and such illustrations and exploded views as may be required to permit proper maintenance by qualified mechanics. The manual shall contain an alphabetical subject index as well as a table of contents. The service manual sh

30、all contain at least the following, where applicable: a. Fire fighting system schematic(s). b. Hydraulic schematic. c. Pneumatic schematic. d. Electrical schematic. e. Winterization schematic. f. Schedules for required preventative maintenance and required periodic maintenance. g. Location, procedur

31、e, and interval for parts of the truck and equipment which require lubrication. 2.1.8.1.3 Parts manual. The parts manual shall include illustrations and exploded views, as needed, to properly identify all parts, assemblies, subassemblies, and special equipment. All components of assemblies shown in

32、illustrations or exploded views shall be identified by reference numbers which correspond to the reference numbers in the parts lists. All purchased parts shall be cross-referenced with the original manufacturers name and part number. The parts identification manual shall provide the description, le

33、ngth, dimensions, and quantity of each item used per vehicle. The manual shall contain a numerical index. The parts manual shall contain a list of all of the component vendor names, addresses, and telephone numbers referenced in the parts list. Provided by IHSNot for ResaleNo reproduction or network

34、ing permitted without license from IHS-,-,-A-A-59879 5 2.1.9 Painting, plating, and corrosion control. 2.1.9.1 Dissimilar metals. Dissimilar metals, as defined in MIL-STD-889, shall not be used in intimate contact with each other. 2.1.9.2 Finish. Exterior surfaces shall be prepared, primed, and pain

35、ted with polyurethane paint in accordance with all of the paint manufacturers instructions and recommendations. The exterior finish color shall be Candy Apple Red, Sikkens Color Number FLNA3021, DuPont Color Number 97902U or 4737U, PPG Color Number 71528 (the PPG name for this color is Cardinal Red)

36、, or equal. The cab upper body (from the bottom of the windshield) and roof shall be painted White, Color Number 17875 of FED-STD-595. Compartment interiors shall have a standard commercial finish. All bright metal and anodized parts, such as mirrors, horns, light bezels, and treadplate, shall not b

37、e painted. Roll-up compartment doors may be painted or unpainted. 2.1.9.3 Horizontal reflective striping. Horizontal reflective striping in accordance with NFPA 1901 shall be applied around the vehicle in an approximate plane with the headlights. Bright metal trim or anodized parts may interrupt the

38、 reflective stripes. The pattern shall be 10 inches wide with three reflective stripes (one inch reflective, one inch body color, 6 inches reflective, one inch body color, and one inch reflective). The reflective stripes shall be white in color. 2.1.9.4 Chevron striping. In accordance with 15.9.3.2

39、of NFPA 1901 at least 50 percent of the rear-facing vertical surfaces, visible from the rear of the apparatus, excluding any pump panel areas not covered by a door, shall be equipped with retroreflective striping in a chevron pattern sloping downward and away from the centerline of the vehicle at an

40、 angle of 45 degrees. 3M part number 983-17 (red) and 983-23 (florescent yellow/green) reflective diamond grade or equivalent shall be utilized. Each stripe in the chevron shall be a single color alternating between red and fluorescent yellow in accordance with 15.9.3.2.1. Each stripe shall be 6 inc

41、hes in width in accordance with 15.9.3.2.2 of NFPA 1901 and the example provided on the next page. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59879 6 2.1.9.5 Lettering. The letters UNITED STATES and AIR FORCE shall be applied in synthetic or

42、 encapsulated gold leaf, with outline and black shadow, on the front door on both sides in long radius elliptical arches above and below the lettering center line. The size of the lettering shall be a minimum of 2 inches to a maximum of 6 inches. 2.1.10 Identification plate. A permanently marked ide

43、ntification plate shall be securely mounted at the drivers compartment. The identification plate shall contain the following information: a. NOMENCLATURE b. MANUFACTURERS MAKE AND MODEL c. MANUFACTURERS SERIAL NUMBER d. USAF VEHICLE REGISTRATION NUMBER e. NATIONAL STOCK NUMBER (NSN) f. VEHICLE CURB

44、WEIGHT: kg (pounds) g. PAYLOAD, MAXIMUM: kg (pounds) h. GROSS VEHICLE WEIGHT (GVW): kg (pounds) i. FUEL CAPACITY AND TYPE: gal (gallons) / L (liters) j. DATE OF DELIVERY (month and year) k. WARRANTY (months and km (miles) l. CONTRACT NUMBER m. PAINT COLOR AND NUMBER Provided by IHSNot for ResaleNo r

45、eproduction or networking permitted without license from IHS-,-,-A-A-59879 7 n. LENGTH, WIDTH, AND HEIGHT OF VEHICLE IN INCHES AND CENTIMETERS. 2.2 General requirements. 2.2.1 Hose storage. 2.2.1.1 Hose storage area. The vehicle shall have a hose bed, with a removable and secured hose bed cover and

46、two adjustable dividers, capable of carrying 1,000 feet of 5 inch hose and 800 feet of 3 inch hose. 2.2.1.2 Speed lay hose beds. The vehicle shall have two speed lay hose beds with one or more removable and secured hose bed covers. Hose bed covers will be red in color. The hose beds shall be capable

47、 of carrying 200 feet of 1 inch pre-connected hose each. Sufficient clearance shall be provided between the hose and cover to allow a pre-connected hose nozzle to be pulled through from either side of the vehicle. Speed lay hose bed covers shall be red in color. Covers will be secured by snap fasten

48、ers. 2.2.1.3 Hose board trays. The vehicle shall be equipped with two running board hose trays located under discharge panels on both the driver and crew chief side. Each tray shall be equipped with a mat and shall be designed to allow for proper drainage. 2.2.2 Suction hose. 2.2.2.1 Hard suction ho

49、se. Two 10 foot long, light weight 6 inch hard suction hoses, with 6-inch National Hose thread long handle female couplers on one end and 6 inch National Hose thread long handle male couplers on the other, shall be mounted on the vehicle above the left side compartments. A suction strainer shall also be mounted on the vehicle. The hose and suction strainer mounting system design shall be s