AECMA PREN 9300-010-2006 Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data Part 010 Overview Data Flow.pdf

《AECMA PREN 9300-010-2006 Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data Part 010 Overview Data Flow.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 9300-010-2006 Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data Part 010 Overview Data Flow.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、ASD STANDARD NORME ASD ASD NORM prEN 9300-010 Edition P 1 October 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONGulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION Aerospace

2、series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 010: Overview Data Flow Srie arospatiale LOTAR Archivage Long Terme et rcupration des donnes techniques produits numriques, telles que CAD 3D et PDM Partie 010 : Vue gnrale du

3、flux de donnes Luft- und Raumfahrt LOTAR Langzeitarchivierung und Bereitstellung digitaler technischer Produktdokumentationen, beispielsweise 3D CAD und PDM Daten Teil 010: bersicht Datenfluss This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace a

4、nd Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical conten

5、t shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee

6、for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for

7、publication 31 October 2006 Comments should be sent within six months after the date of publication to ASD-STAN Engineering Procedures and Processes Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA No

8、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-010:20062 Contents Page Foreword .3 1 Scope4 2 Normative references4 3 Terms, definitions and abbreviations .4 4 Applicability .4 5 Overview data flow5 6 Detailed process steps description.6 6.1 Data Preparati

9、on6 6.2 Ingest 6 6.3 Archival Storage6 6.4 Retrieval .6 6.5 Removal6 6.6 Ingest of pre existing data7 7 Data descriptions 7 7.1 Involved roles: .7 7.2 Involved data: 7 Bibliography9 Figure Figure 1 Overview data flow 5 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provide

10、d by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-010:2006 3 Foreword This standard was prepared jointly by ASD-STAN and the PROSTEP iViP Association. The PROSTEP iViP Association is an international non-profit association

11、in Europe. For establishing leadership in IT-based engineering it offers a moderated platform to its nearly 200 members from leading industries, system vendors and research institutions. Its product and process data standardization activities at European and worldwide levels are well known and accep

12、ted. The PROSTEP iViP Association sees this standard and the related parts as a milestone of product data technology. Users should note that all standards undergo revision from time to time and that any reference made herein to any other standard implies its latest edition, unless otherwise stated.

13、Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-010:20064 1 Scope EN 9300-010 provides a overview description for the recommended processes

14、for archiving of 3D product data, e.g. 3D CAD and PDM data. The processes are described in EN 9300-011 to EN 9300-016. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated r

15、eferences, the latest edition of the referenced document (including any amendments) applies. ISO 14721:2003, Space data and information transfer systems Open archival information system Reference model OAIS. EN 9300-007, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical p

16、roduct documentation such as 3D, CAD and PDM data Part 007: Terms and References. 1) EN 9300-011, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 011: Reference process description “Data preparation“. 2) EN 9300-01

17、2, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 012: Reference process description “Ingest“. 2) EN 9300-013, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation su

18、ch as 3D, CAD and PDM data Part 013: Reference process description “Archival Storage“. 2) EN 9300-014, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 014: Reference process description “Retrieval“. 2) EN 9300-015,

19、 Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 015: Reference process description “Removal“. 2) EN 9300-016, Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation suc

20、h as 3D, CAD and PDM data Part 016: Reference process description “Ingest for pre-existing data“. 1) 3 Terms, definitions and abbreviations For the purposes of this standard, the terms, definitions and abbreviations given in EN 9300-007 shall apply. 4 Applicability This EN 9300-010 is applicable to

21、new 3-D product data records and may be applicable to existing 3D product data records, on current and earlier products, produced using previous regulations, standards and procedures. The current version is focused on product data as defined in the domain specific parts. 1) In preparation at the dat

22、e of publication. 2) Published as ASD Prestandard at the date of publication of this standard. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 93

23、00-010:20065 5 Overview data flow Figure 1 Overview data flow The overview data flow is divided into several phases. This includes the phases: Data preparation Ingest Archival Storage Retrieval Removal The overview is organized along the life cycle of the data to be archived. For this the Producer h

24、as to prepare the data. After Data Preparation the resulting Submission Information Package (SIP) will be send during an Ingest Process to the Archive System. Within the Archival Storage Process the SIP will be converted into an Archival Information Package (AIP). This includes the conversion of nat

25、ive formatted product data into the archive format as well as the signing of the data with a digital time signature. For reuse or viewing, the data Consumer has the ability to retrieve the archived data. The archiving system provides in addition the optional Removal Process step. The ingest process

26、for pre existing data describes the automatic process of conversion and storage of an already existing archive (and data) into the recommended archive format (See EN 9300-016). The phases Data Generation and Data Usage and Process step #7 Data usage are out of scope for EN 9300-010. The phases and t

27、he process step are integrated for process modeling reasons. The supporting processes (for example, “data preservation”, ”data management”, and “administration”) are not identified on the Figure 1. They will be introduced, when useful, on the parts detailing the processes (EN 9300-011 to EN 9300-015

28、). Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-010:20066 The Descriptive Information is not identified on the Figure 1. It will be intro

29、duced, when useful, on the parts detailing the processes (EN 9300-011 to EN 9300-015). The Descriptive Information represents the set of information, consisting primarily of Package Descriptions, which is provided to Data Management to support the finding, ordering, and retrieving by Consumers of ar

30、chived information holdings. 6 Detailed process steps description 6.1 Data Preparation The data to be archived will be prepared by the producer. This includes defined data verification, performed by a Quality Agent tool. The data verification will test the data against defined data quality requireme

31、nts, and will provide a result report. Data preparation also includes the creation of validation properties. The sub process shall be certified. For detailed refer to EN 9300-011 “Data Preparation“. 6.2 Ingest During the Ingest process the data producer submits the SIP from the preparation environme

32、nt into the archiving environment. The archive receives the data packages and checks if the SIP contains data of the recommended format and then generates the AIP. It is recommended that the Producer environment makes the source data read only after successful submission of the SIP to the archive. T

33、he sub process shall be certified. For details refer to EN 9300-012 “Ingest“. 6.3 Archival Storage The process includes the setting of digital time signatures, generation of additional Descriptive Information (DI) for AIPs (meta data for the archive), the physical storage of the data within the arch

34、ive and error checking as well as the steps needed disaster recovery of the stored data. Each company should meet the general recommendations for an archive system and its security, as for example described in ISO 14721:2003 (OAIS). These general recommendations are out of scope. The sub process sha

35、ll be certified. For details refer to EN 9300-013 “Archival Storage“. 6.4 Retrieval The process includes a recommended access check, provides functionality for a data search to select the required data (provided the Consumer is allowed to see it), and the generation of a Dissemination Information Pa

36、ckage (DIP). The generation of the DIP should meet the requirements of the Consumer. The sub process shall be certified. For details refer to EN 9300-014 “Retrieval“. 6.5 Removal Data removal can be initiated either by the rules management system or administrator or by an automatic request generated

37、 by the archive. The removal can be performed in two ways: Deletion of relevant data, or Outsourcing of data, for example into a (technical) museum, which does not meet the requirements of a long term archive. Inappropriate removal of data may cause difficulties in data path traceability. Caution sh

38、ould be exercised before any data removal. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 9300-010:20067 The process includes access control fun

39、ctionality for security reasons and data selection functionality for manual selection. The Content Information of the AIP will be deleted from the archive, but the deletion information remains within the archives meta data. The removal process checks afterwards the data is correctly deleted and prov

40、ides a status report. Because data may be stored on permanent media, each company has to decide if a removal process of data be implemented. The implementation of this process is optional. For details refer to EN 9300-015 “Removal“. 6.6 Ingest of pre existing data Within the automatically controlled

41、 Ingest process for pre existing data, the pre existing data (archive) will be converted into the recommended archiving format and stored in the long term archive. This process step is only relevant for pre existing 3D product data, e.g. CAD and PDM data, which fulfil the defined data quality criter

42、ia of this reference process. In case of implementation, the process shall be certified. For details refer to EN 9300-016 “Ingest for pre existing data”. 7 Data descriptions 7.1 Involved roles: 7.1.1 Archive The Archive is the archiving environment, which usual supports at least the key functions of

43、 an archiving architecture according to ISO 14721 (OAIS). Key functions are administration, data management, archival storage, access control, preservation planning. 7.1.2 Consumer The consumer is an organization, person, or client system, which interact with the services offered by the archive to f

44、ind preserved information of interest and to access that information in detail. This can include other archives, as well as internal archive personnel or system components. Typical roles of type “consumer“ may be Design Engineers, Suppliers, Manufactures, Customers, Regulatory and Certification Agen

45、cies or Quality Departments. 7.1.3 Producer The producer is an organization, person, or client system, which provides the information to be preserved. This can include other archives or internal archive personnel or system components. Typical roles of type “producer“ may be. System Designers, Design

46、 Engineers, Subcontractors, Manufactures or Test Engineers. 7.2 Involved data: 7.2.1 Archival Information Package (AIP) The AIP consists of the following elements: Content Information (CI) (archiving formatted and optionally native formatted) Packaging Information (PI) Preservation Description Infor

47、mation (PDI) (Validation Properties, context information for the Content Information) Digital Signature Information Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license

48、 from IHS-,-,-prEN 9300-010:20068 The Content Information is the set of information that the producer requires to retain and has all the qualities needed for permanent storage. Packaging information is the information that is used to bind and identify the components of an Information Package. Preser

49、vation Description Information is the information which is necessary for adequate preservation of the Content Information and which can be categorized as Provenance, Reference, Fixity, and Context information. Digital Signature Information is the information about authenticity (identify the signature