AECMA PREN 6113-2003 Aerospace Series Circuit breaker connecting and attachment hardware Edition P 1《航空航天系列.电路断路器连接附件硬件.P1版》.pdf

《AECMA PREN 6113-2003 Aerospace Series Circuit breaker connecting and attachment hardware Edition P 1《航空航天系列.电路断路器连接附件硬件.P1版》.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 6113-2003 Aerospace Series Circuit breaker connecting and attachment hardware Edition P 1《航空航天系列.电路断路器连接附件硬件.P1版》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 30 June 2003 prEN 6113 Edition P 1 June 2003 Comments should be sent within six months after the date of publication to Electrical Domain AECMA-STAN ICs: Descriptors: ENGLISH VERSION Aerospace series Circuit breaker, connecting a

2、nd attachment hardware Srie arospatiale Disjoncteurs, connecteur et montage accessoires Luft- und Raumfahrt Schutzschalter, Anschluss- und Montage- Zubehr This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries -

3、Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that inter

4、changeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote and transformat

5、ion to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Copyright Association Europeene des Constructeurs de Materiel Aerospatial

6、 Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 61 13: 2003 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANS Electrical Domain. After inquiries and votes carried out in accor

7、dance with the rules of AECMA-STAN defined in AECMA- STANS General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope 3 2 Normative references . 3 3 Requirements 3 4 Designation . 8 5 Marking . 8 6 Technical specification 8 Copyright Association Europeene des

8、Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 61 13: 2003 1 Scope This standard specifies the connecting and attaching hardware for circuit breakers. 2 Normative references

9、This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these pub

10、lications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 965-2, IS0 1190-1, IS0 4757, EN 2424, TR 3775, MIL-B-87114, MI L-S-8879, IS0 general purpose metric screw threads - T

11、olerances - Part 2: Limits of sizes for general purpose external and internal screw threads - Medium quality Copper and copper alloys - Code of designation - Part I: Designation of materials Cross recesses for screws Aerospace series - Marking of aerospace products Aerospace series - Bolts and pins

12、- Materials 1 ) Bolts, recess drive, general specification 2) Screw threads, controlled radius root with increased minor diameter, general specification for 2) 3 Requirements 3.1 The configuration, dimensions and tolerances shall conform with subclauses 3.2, 3.3, 3.4 and 3.5. Configuration - Dimensi

13、ons - Tolerances 3.2 Connecting screw 3.2.1 Configuration Configuration, see Figures 1, 2, 3 and 4. 3.2.2 Dimensions and tolerances Dimensions and tolerances are in millimetres. 3.2.3 Thread and Cross recess 3.2.3.1 Thread 0.1 640-32UNC-3A in accordance with MIL-S-8879 3.2.3.2 Cross recess Cross rec

14、ess in accordance with IS0 4757 type H, No.2 3.2.4 Material and protection 3.2.4.1 Material Material: Steel, rupture resistance 860 MPa to 1 O00 MPa in accordance with TR 3775 1) Published as AECMA Technical Report at the date of publication of this standard 2) Published by: Department of Defense (D

15、OD), the Pentagon, Washington D.C. 20301 USA. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 61 13: 2003 Number of EN standard Code for co

16、nnecting screw Size code 3.2.4.2 Protection Protection: Nickel plated (thickness 5 pm min.) 7,6 f 0,2 l-4 A (in larger scale) -LL* 2 f 0,l 1,2 max. - Key 1 Marking, see clause 5. 2 Cross recess, see subclause 3.2.3.2. Figure 1 - Configuration of connecting screw Copyright Association Europeene des C

17、onstructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 61 13: 2003 3.3 Connecting lockwasher 3.3.1 Configuration Configuration, see Figure 2. 3.3.2 Dimensions and tolerances Dimension

18、s and tolerances are in millimetres. 3.3.3 Requirements Two wave corrugated washer 3.3.4 Material and hardness 3.3.4.1 Material Material: CuBe 1,9 to IS0 11 90-1 3.3.4.2 Hardness Hardness: 350 HV to 410 HV Figure 2 - Configuration of connecting lockwasher 3.3.5 Designation of connecting lockwasher E

19、xample of designation for a single connecting lockwasher: Description block Identity block Lockwasher, connecting EN61 13CW04 Number of EN standard Code for connecting lockwasher Diameter code Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license wit

20、h AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 61 13: 2003 3.4 Attachment nut 3.4.1 Configuration Configuration, see Figure 3. 3.4.2 Dimensions and tolerances Dimensions and tolerances are in millimetres. 3.4.3 Material and protection 3.4.3.1 Ma

21、terial Material: Aluminium alloy 3.4.3.2 Protection Protection: Black sulphur anodized Figure 3 - Configuration of attachment nut Table 1 - Dimensions of attachment nut Size code A thread IS0 965-2 B f 0,l I o1 I M12x0,75 I 230 I 02 I M12x1 I 295 3.4.4 Designation of attachment nut Example of design

22、ation for a single attachment nut: Description block Identity block Nut, attachment Number of EN standard Code for attachment nut Size code Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking pe

23、rmitted without license from IHS-,-,-Page 7 prEN 61 13: 2003 3.5 Attach ment lockwas her 3.5.1 Configuration Configuration, see Figure 4. 3.5.2 Dimensions and tolerances Dimensions and tolerances are in millimetres. 3.5.3 Requirements MI 2DIC lockwasher (internal overlapping teeth) 3.5.4 Material an

24、d hardness 3.5.4.1 Material Material: Steel 3.5.4.2 Hardness Hardness: 400 HV to 480 HV 0 17,OO f 0,20 a 0,50 f 0,03 e Figure 4 - Configuration attachment lockwasher 3.5.5 Designation of attaching lockwasher Example of designation for a single attachment lockwasher: Description block Identity block

25、Lockwasher, attachment EN61 13AWO1 Number of EN standard Code for attachment lockwasher Size code Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page

26、8 prEN 61 13: 2003 EN 61 13CSO8-O1 EN 61 13CW04 EN 61 13AN01 EN 61 13A 4 Designation Connecting screw 2 Connecting lockwasher 2 Attachment nut 1 Example of a hardware kit: Description block I Identity block EN 61 13AN01 EN 61 13AW01 EN 61 13CSO8-O1 EN 61 13B Hardware, kit I EN6113 Number of EN stand

27、ard Hardware kit code (see Table 1) 4.1 Hardware kit code Table 2 - Hardware kit code Attachment nut 1 Attachment lockwasher 1 Connectinci screw 6 See Table 2. EN 61 13CW04 EN 61 13AN01 EN 61 13C Hardware kit code A B C AI BI CI Connecting lockwasher 6 Attachment nut 1 Components of the hardware kit

28、s Single part-no.a I Description I Pieces per kit Kit part-no. EN 61 13AW01 EN 61 13CSO8-O1 Attachment lockwasher 1 Connecting screw 2 I EN 61 13AW01 I Attachment lockwasher I 1 I EN 61 13CW04 EN 61 13AN02 EN 61 13A1 Connecting lockwasher 2 Attachment nut 1 EN 61 13AN02 EN 61 13AW01 EN 61 13CSO8-O1

29、EN 61 13B1 Attachment nut 1 Attachment lockwasher 1 Connectina screw 6 EN 61 13CW04 EN 61 13AN02 EN 61 13C1 I EN 61 13AW01 I Attachment lockwasher I 1 I Connecting lockwasher 6 Attachment nut 1 I EN 61 13AW01 I Attachment lockwasher I 1 I I a Spare parts can be ordered separately. I 5 Marking The pa

30、ckaging of kits and single parts (spare parts) must be marked in accordance with EN 2424 style P. The parts can be marked with manufacturers logo. 6 Tech n i cal specification As per MIL-B-87114, unless otherwise specified. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-