ABS 2-2017 RULES FOR BUILDING AND CLASSING STEEL VESSELS 2017.pdf

《ABS 2-2017 RULES FOR BUILDING AND CLASSING STEEL VESSELS 2017.pdf》由会员分享，可在线阅读，更多相关《ABS 2-2017 RULES FOR BUILDING AND CLASSING STEEL VESSELS 2017.pdf（4357页珍藏版）》请在麦多课文档分享上搜索。

1、 Notices and General Information RULES FOR BUILDING AND CLASSING STEEL VESSELS 2017 NOTICES AND GENERAL INFORMATION American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 2016 American Bureau of Shipping. All rights reserved. ABS Plaza 16855 Northchase Drive Hou

2、ston, TX 77060 USA Table of Contents part Notices and General Information CONTENTS Introduction . 1 TABLE 1 Applicable Editions of Booklets Comprising 2017 Rules 4 TABLE 2 Division and Numbering of Rules 4 Rule Change Notice (2017) . 5 TABLE 3 Summary of Changes from the 2016 Rules 5 ii ABSRULES FOR

3、 BUILDING AND CLASSING STEEL VESSELS .2017 Notices and General Information Introduction 1. The year 2017 edition of the Rules for Building and Classing Steel Vessels consists of the eleven (11) booklets as shown in Table 1. In this regard, we would bring the following to the users attention: a) The

4、purpose of the generic title ABS Rules for Conditions of Classification (Part 1) is to reflect the expanded contents of PART 1, as a result of including consolidated requirements for “Classification” applicable to all types of and sizes of vessels, barges and specific shipboard arrangements/systems,

5、 etc., except for those in offshore service, as specified in the Foreword to Part 1. b) The purpose of the generic title ABS Rules for Materials and Welding (Part 2) of PART 2 is to emphasize the common applicability of the requirements to ABS-classed vessels, other marine structures and their assoc

6、iated machinery, and thereby make PART 2 more readily a common “PART” of various ABS Rules and Guides, as appropriate. c) The purpose of the generic title ABS Rules for Survey After Construction (Part 7) is to reflect the expanded contents of PART 7, as a result of including consolidated requirement

7、s for “Surveys After Construction” applicable to all types and sizes of vessels, barges and specific shipboard arrangements/systems, etc., as specified in Part 7, Chapter 1, Section 1. 2. The numbering system applied in the Rules is shown in Table 2. 3. The primary changes from the 2016 edition of t

8、he Rules are identified and listed in Table 3. The effective date of the indicated Rule Changes is 1 January 2017, unless specifically indicated otherwise. 4. The effective date of each technical change since 1993 is shown in parenthesis at the end of the subsection/paragraph titles within the text

9、of each Part. Unless a particular date and month are shown, the years in parentheses refer to the following effective dates: (2000) and after 1 January 2000 (and subsequent years) (1996) 9 May 1996 (1999) 12 May 1999 (1995) 15 May 1995 (1998) 13 May 1998 (1994) 9 May 1994 (1997) 19 May 1997 (1993) 1

10、1 May 1993 For certain changes that have a major impact on shipyards, designers and vendors, ABS has instituted a two-year Rule cycle to give the industry more time to prepare for these changes. The text of these changes will appear in a box along with the effective date just under the existing Rule

11、 requirement. 5. Until the next edition of the Rules for Building and Classing Steel Vessels is published, Rule Change Notices and/or Corrigenda, as necessary, will be published on the ABS website www. eagle.org only, and will be available free for downloading. It is not intended to publish hard cop

12、ies of future Rule Change Notices and/or Corrigenda to existing Rules or Guides. The consolidated edition of the Rules for Building and Classing Steel Vessels, which includes Rule Change Notices and/or Corrigenda using different colors for easy recognition, will be published on the ABS website only

13、when Rule Change Notices and/or Corrigenda are issued. 6. The listing of CLASSIFICATION SYMBOLS AND NOTATIONS is available from the ABS website http:/www.eagle.org/absdownloads/index.cfm for download. ABSRULES FOR BUILDING AND CLASSING STEEL VESSELS .2017 1 Notices and General Information 7. In asso

14、ciation with the harmonization of the Common Structural Rules (CSR) for Bulk Carriers and Oil Tankers, on 1 July 2015, the three Sub-parts, 5A, 5B, and 5C, of Part 5 of the Rules for Building and Classing Steel Vessels are as follows: Contents Part 5A: General Hull Requirements (IACS CSR Part 1) Par

15、t 5B: Ship Types (IACS CSR Part 2) Part 5C: This Part is divided into two separate booklets as follows: Chapters 1 to 6: Tankers and Bulk Carriers not covered by Part 5A and Part 5B and Container Carriers Chapters 7 to 13: Passenger Vessels, Liquefied Gas Carriers, Chemical Carriers, Vessels Intende

16、d to Carry Vehicles, Water Carriers, Membrane Tank LNG Carriers, and Vessels Using Gases or other Low-Flashpoint Fuels. Application Oil Tankers The structural requirements in Part 5A, Pt 1 and Part 5B, Pt 2, Ch 2 of the Rules are applicable for double hull oil tankers of 150 m in length and upward,

17、with structural arrangements as specified in Part 5A, Pt 1, Ch 1, Sec 1, 1.3. For oil tankers with structural arrangements not covered by Part 5A, Pt 1 and Part 5B, Pt 2, Ch 2, the requirements in Part 5C, Chapters 1 or 2, are to be complied with. Application Bulk Carriers The structural requirement

18、s in Part 5A, Pt 1 and Part 5B, Pt 2, Ch 1 of the Rules are applicable for single side skin and double side skin bulk carriers of 90m in length and upward, with structural arrangements as specified in Part 5A, Pt 1, Ch 1, Sec 1, 1.2. For vessels intended to carry ore or bulk cargoes, other than the

19、single side skin or double side skin bulk carriers of 90 m in length and upward with structural arrangements as specified in Part 5A, Pt 1 and Part 5B, Pt 2, Ch 1, the requirements in Part 5C, Chapters 3 or 4 are to be complied with. Application ABS Construction Monitoring Program These compulsory r

20、equirements for CSR notation are specified in Part 5C, Appendix 2. Application Onboard Systems for Oil Tankers and Bulk Carriers The onboard systems for all tankers are to comply with the requirements of Part 5C, Chapter 1, Section 7, and for all bulk carriers are to comply with the requirements of

21、Part 5C, Chapter 3, Section 7 of the Rules. Application References Other Parts of the ABS Rules that are referenced within Part 5A, 5B, or 5C are also to be applied. The following flow chart indicates the application of the Rules and typical Class Notations for tanker and bulk carrier vessels, of wh

22、ich arrangements and scantlings are in full compliance with the Rules: 2 ABSRULES FOR BUILDING AND CLASSING STEEL VESSELS .2017 Notices and General Information Vessels Intended to Carry Oil in Bulk Vessels Intended to Carry Ore or Bulk Cargoes L 150 m? Arrangement and layout comply with Part 5A, Pt

23、1, Ch 1, Sec 1, 1.3 and Part 5A, Pt 1, Ch 1, Sec 1, Figure 3? Part 5A, Pt 1 and Part 5B, Pt 1, Ch 2: Common Structural Rules and Part 5C, Appendix 2 Part 5C, Chapter 1, Section 7: ABS Steel Vessel Rules A1 Oil Carrier, CSR, AB-CM plus appropriate notations for oil carriers Part 5C, Chapter 1, Append

24、ix 1 to Part 5C ABS Steel Vessel Rules (L 150 m) A1 Oil Carrier, SH, SHCM plus appropriate notations for oil carriers Part 5C, Chapter 2 ABS Steel Vessel Rules (L 150 m) A1 Oil Carrier plus appropriate notations for oil carriers L 90 m? Arrangement and layout comply with Part 5A, Pt 1, Ch 1, Sec 1,

25、1.2 and Part 5A, Pt 1, Ch 1, Sec 1, Figures 1 & 2? Part 5A, Pt 1 and Part 5B, Pt 1, Ch 1: Common Structural Rules and Part 5C, Appendix 2 Part 5C, Chapter 3, Section 7: ABS Steel Vessel Rules Part 5C, Chapter 3, Appendix 1 to Part 5C ABS Steel Vessel Rules (L 150 m) Part 5C, Chapter 4 ABS Steel Vess

26、el Rules (L 150 m) A1 Bulk Carrier, CSR, AB-CM plus appropriate notations for bulk carriers A1 Bulk Carrier, SH, SHCM plus appropriate notations for bulk carriers A1 Bulk Carrier plus appropriate notations for bulk carriers Yes Yes Yes Yes No No Or No NoABSRULES FOR BUILDING AND CLASSING STEEL VESSE

27、LS .2017 3 Notices and General Information TABLE 1 Applicable Editions of Booklets Comprising 2017 Rules Notices and General Information 2017 Part 1: Rules for Conditions of Classification 2017 Part 2: Rules for Materials and Welding Rules for Testing and Certification of Materials Rules for Welding

28、 and Fabrication 2017 Part 3: Hull Construction and Equipment 2017 Part 4: Vessel Systems and Machinery 2017 Part 5A: (Booklet 1) Specific Vessel Types General Hull Requirements (IACS CSR Part 1) 2017 (on and after 1 July 2016) Part 5B: (Booklet 1) Specific Vessel Types Ship Types (IACS CSR Part 2)

29、2017 (on and after 1 July 2016) Part 5C: (Booklet 2) Specific Vessel Types Chapter 1 & 2 Oil Carrier Chapter 3 & 4 Bulk Carrier Chapter 5 & 6 Container Carrier 2017 Part 5C: (Booklet 3) Specific Vessel Types Chapter 7 Passenger Carrier Chapter 8 Liquefied Gas Carrier Chapter 9 Chemical Carrier Chapt

30、er 10 Vehicle Carrier Chapter 11 Water Carrier Chapter 12 Liquefied Gas Carrier with Membrane Tanks 2017 Part 6: Optional Items and Systems Chapter 1 Strengthening for Navigation in Ice Chapter 2 Refrigerated Cargo Vessels 2017 Part 7: Rules for Survey After Construction 2017 TABLE 2 Division and Nu

31、mbering of Rules Division Number Part Part 1 Chapter Part 1, Chapter 1 Section Section 1-1-1 Subsection (see Note 1) 1-1-1/1 Paragraph (see Note 1) 1-1-1/1.1 Subparagraph 1-1-1/1.1.1 Item 1-1-1/1.1.1(a) Subitem 1-1-1/1.1.1(a)i) Appendix Appendix 1-1-A1 or Appendix 1-A1-1 Note: 1 An odd number (1, 3,

32、 5, etc.) numbering system is used for the Rules. The purpose is to permit future insertions of even-numbered paragraphs (2, 4, 6, etc.) of text and to avoid the necessity of having to renumber the existing text and associated cross-references, as applicable, within the Rules and associated process

33、instructions, check sheets, etc. 4 ABSRULES FOR BUILDING AND CLASSING STEEL VESSELS .2017 Notices and General Information Rule Change Notice (2017) TABLE 3 Summary of Changes from the 2016 Rules EFFECTIVE DATE 1 July 2016 shown as (1 July 2016) Part/Para. No. Title/Subject Status/Remarks PART 1 Rule

34、s for Conditions of Classification 1-1-A3/5.5 Product Quality Assurance Certification (PQA) Tier 4 (IACS UR Z26 Alternative Certification Scheme) To incorporate IACS UR Z26, which replaces UR M5 & UR M14. (Incorporates Notice No. 1) EFFECTIVE DATE 1 August 2016 shown as (1 August 2016) Part/Para. No

35、. Title/Subject Status/Remarks PART 1 Rules for Conditions of Classification 1-1-2/11.7 (New) To specify that classification may be cancelled upon a vessels sale or transfer without prior written notice to ABS. (Incorporates Notice No. 2) 1-1-2/11.9 (New) To be able to cancel Class on vessels in lay

36、up, where these have been sold and new Owners are not willing to communicate with ABS. (Incorporates Notice No. 2) EFFECTIVE DATE 1 January 2017 shown as (2017) Part/Para. No. Title/Subject Status/Remarks PART 1 Rules for Conditions of Classification 1-1-3/31 Domestic Service Notation To provide the

37、 reference to the Appendix 5-A1 of the ABS Rules for Building and Classing Steel Vessels Under 90 meters (295 feet) in Length. 1-1-4/7.5 Other Rules To avoid misunderstanding of SHR notation that has been assigned to existing non-CSR tankers. 1-1-7/1 Hull Plans To clarify that plans and calculations

38、 are to be submitted for mooring structures. 1-1-A3/5.7.2(a) Issuance of Certificates To clarify that 90 days is prior to the expiration of the certificate. EFFECTIVE DATE 1 January 2017 shown as (2017) (based on the date of purchase order of the materials) Part/Para. No. Title/Subject Status/Remark

39、s PART 2 Rules for Materials and Welding 2-1-1/7.2 Electronic Certification System To mitigate the risk of misrepresentation on ABS approval by the client. 2-1-5/5 Heat Treatment To clearly indicate that HT facilities can be approved independently, if they carry out the mechanical tests and NDE. 2-1

40、-6/1.1 General To clearly indicate that the raw material such as ingots or billets or others is to be procured from an ABS approved facility. ABSRULES FOR BUILDING AND CLASSING STEEL VESSELS .2017 5 Notices and General Information Part/Para. No. Title/Subject Status/Remarks 2-1-6/5.1 General To clea

41、rly indicate that the raw material such as ingots or billets or others is to be procured from an ABS approved facility. 2-3-7/1.1.1 General To clearly indicate that the raw material such as ingots or billets or others is to be procured from an ABS approved facility. 2-3-7/1.5.1 General To clearly in

42、dicate that HT facilities can be approved independently, if they carry out the mechanical tests and NDE. 2-3-7/1.11.1(c) Small Forgings To specify that in the case of carbon and low alloy steel small forgings, test sampling is based on the furnace mass rather than the no. of forgings, in line IACS W

43、7. 2-3-7/Figure 1 (New) Gear Ring Forgings Test Specimen Locations and Orientations To clearly indicate the test coupon locations for carbon and low alloy steels. 2-3-7/Figure 2 (New) Pinion or Gear Forging Test Specimen Locations and Orientations To clearly indicate the test coupon locations for ca

44、rbon and low alloy steels. 2-3-7/Figure 3 (New) Gear Shaft Forging Test Specimen Locations and Orientations To clearly indicate the test coupon locations for carbon and low alloy steels. 2-3-7/1.11.1(g) Surface Hardened Forgings To indicate that the carburized forging requirement is also applicable

45、to other types of surface hardening processes (except for induction hardening). 2-3-7/1.11.1(h) (New) Continuous Heat Treatment To indicate the continuous heat treatment requirements are to be specially agreed with ABS. 2-3-7/1.5.7 Surface Hardening To clearly indicate that HT facilities can be appr

46、oved independently, if they carry out the mechanical tests and NDE. 2-3-7/3.1.1 General To clearly indicate that the raw material such as ingots or billets or others is to be procured from an ABS approved facility. 2-3-7/3.5.1 General To clearly indicate that HT facilities can be approved independen

47、tly, if they carry out the mechanical tests and NDE. 2-3-7/3.5.8 (New) Surface Hardening To clearly indicate that HT facilities can be approved independently, if they carry out the mechanical tests and NDE. 2-3-7/3.9.3(c) Small Forgings To specify that in the case of carbon and low alloy steel small

48、 forgings, test sampling is based on the furnace mass rather than the no. of forgings, in line IACS W7. 2-3-7/Figure 4 (New) Pinion or Gear Forging Test Specimen Locations and Orientations To clearly indicate the test coupon locations for carbon and low alloy steels. 2-3-7/Figure 5 (New) Gear Shaft

49、Forging Test Specimen Locations and Orientations To clearly indicate the test coupon locations for carbon and low alloy steels. 2-3-7/3.9.3(g) Surface Hardened Forgings To indicate that the carburized forging requirement is also applicable to other types of surface hardening processes (except for induction hardening). 2-3-7/3.9.3(h) (New) Continuous Heat Treatment To indicate the continuous heat treatment requirements are to be specially agreed with ABS. 2-3-7/5.1.1 General To clearly indicate that the raw material such as ingots