A-A-59621-2000 NECKERCHIEF (ACETATE BLACK) [Superseded NAVY MIL-N-87042 C NAVY MIL-N-87042 B NAVY MIL-N-87042 A (2) NAVY MIL-N-87042 A (1) NAVY MIL-N-87042 A NAVY MIL-N-87042]《醋酸黑色.pdf

《A-A-59621-2000 NECKERCHIEF (ACETATE BLACK) [Superseded NAVY MIL-N-87042 C NAVY MIL-N-87042 B NAVY MIL-N-87042 A (2) NAVY MIL-N-87042 A (1) NAVY MIL-N-87042 A NAVY MIL-N-87042]《醋酸黑色.pdf》由会员分享，可在线阅读，更多相关《A-A-59621-2000 NECKERCHIEF (ACETATE BLACK) [Superseded NAVY MIL-N-87042 C NAVY MIL-N-87042 B NAVY MIL-N-87042 A (2) NAVY MIL-N-87042 A (1) NAVY MIL-N-87042 A NAVY MIL-N-87042]《醋酸黑色.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH POUND A-A-59621 October 18, 2000 Superseding MIL-N-87042C(NU) February 08, 1988 COMMERCIAL ITEM DESCRIPTION NECKERCHIEF (ACETATE BLACK) The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-N-87042C for all Federal agencies. 1.

2、SCOPE. This commercial item description covers the requirements for a black acetate neckerchief, used by enlisted Navy personnel. 2. CLASSIFICATION. The neckerchief shall be one type and size only. 3. SALIENT CHARACTERISTICS. 3.1 Description. The neckerchief will be a square shape measuring 36 (+3/4

3、, -1/4) inches in both length and width. The color shall be Black shade 3218. There shall be no more than 3/4-inch variation between the length and width dimensions. The finished hems shall be 1/8 to 1/4 inches in width. The overall measurements shall be taken along each edge and in the middle in bo

4、th the length and width directions of the finished neckerchief. The finished neckerchief shall be hemmed on all sides or have two (2) hemmed edges and two (2) selvage edges. All finished neckerchiefs shall be pressed flat. 3.2 Basic material. The basic material for the neckerchief shall be made of s

5、olution dyed 100% Acetate twill cloth. The yarn for the warp and filling shall be a continuous multifilament, bright acetate. The size of the warp and filling yarns shall be 100 denier. 3.3 Cloth. The finished cloth shall conform to the physical requirements specified in Table I. Beneficial comments

6、, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, ATTN: DPSC-CRFD, 700 Robbins Avenue, Building 6D, Philadelphia, PA 19111-5096. AMSC N/A FSC 8440 Provid

7、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59621 2TABLE I. Physical Requirements Characteristics Requirements Test methods Weight oz/sq. yd (minimum) 2.0 ASTM-D-3776, Option C Yarns per inch Warp Filling 128 to 134 77 to 80 ASTM-D-3775 Weave 2 up,

8、 2 down right hand twill Visual 1/ Colorfastness: Laundering (3 cycles) Dry cleaning Perspiration Light (40 hrs) Crocking, wet/dry not less than grade 3 not less than grade 3 not less than grade 3 not less than grade 3 not less than grade 3 AATCC 61, Test 1A Test method 5622 2/ AATCC 15 3/ AATCC 16,

9、 Opt A AATCC 8 4/ Nonfibrous materials, % (maximum) 6 AATCC 20A 5/ Dimensional Stability, % maximum, warp and filling 4 AATCC 135 (3) IV B pH 5.0 to 8.5 AATCC 81 1/ One determination shall be made from each sample unit and the results reports as pass or fail. 2/ Federal Standard 191A. 3/ Acid and al

10、kaline. 4/ Evaluation using AATCC 8 Chromatic Transference Scale. 5/ Non-fibrous shall be determined in accordance with the method prescribed except that perchloroethylene shall be used in lieu of chloroform. 3.4 Finish. The finished cloth shall be desized, scoured, and heat set. Handling finishes a

11、re prohibited. 3.5 Color matching. The standard sample for the basic material shall be referenced for Black 3218. The color of the test specimen shall match the standard sample when viewed under filtered tungsten lamps that approximate artificial daylight, and that have a correlated color temperatur

12、e of 7500K (+/- 200 K), with illumination of 100 (+/- 20) foot-candles, and shall be a good match to the standard under incandescent lamplight at 2300 K ( +/- 200 K). 3.6 Thread. The thread used for the needle and bobbin shall be cotton, comforming to Type Provided by IHSNot for ResaleNo reproductio

13、n or networking permitted without license from IHS-,-,-A-A-59621 3III, 3-ply, Ticket No. 000 of A-A-52094. Cotton or polyester covered thread with a polyester core, Ticket No. 100, 2-ply, conforming to A-A-50199 Type I, may be substituted for the cotton thread. Color shall be Black. Colorfastness of

14、 the thread shall be equal to the basic material. 3.7 Labels. Each neckerchief shall have a cloth or paper type pressure sensitive label. The label shall be attached to a corner of each neckerchief without leaving residue. The inscription below and bar code requirements in 3.7.1 shall appear on the

15、label: NECKERCHIEF 100% ACETATE STOCK NO.: 8440 01 198 5175 USE “LOW” HEAT SETTING WHEN IRONING HAND WASH IN WARM WATER OR DRY CLEAN. 3.7.1 Label/tag. The bar coding element shall be a 13 digit national stock number (NSN). There shall be a 12 digit UPC number assigned for all NSNs by the processing

16、agency. The initials “UPC” must appear beneath the UPC code. The bar code for the NSN and UPC type shall be a medium to high density and shall be located so that it is completely visible on the item when it is folded and/or packaged as specified and so that it causes no damage to the item. 3.8 Stitc

17、hes, seams and stitching. Neckerchief shall have 8-10 stitches per inch for performing hemming operation. When selvage edges are used, the hems of the cut edges shall be backtacked or backstitched 1/2 inch. When cut edges are used, the overlapping hems shall be backtacked or backstitched at each cor

18、ner. All seams shall start and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitching. 4. REGULATORY REQUIREMENTS. 4.1 Flammability requirements. The basic material shall conform to the rules and regulations of the Flammability Fabrics Act without the applicat

19、ion of a flame retardant finish to material or the end item. 4.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered or environmentally referable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and main

20、tenance requirements, and promotes economically advantageous life cycle costs. 4.3 Labeling. The garment shall contain material content and care labels in accordance with the Textile Fiber Act. 5. PRODUCT COMFORMANCE PROVISIONS. 5.1 Product conformance. The products offered shall meet the salient ch

21、aracteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59621 4quality assurance practices, and be the same product that is offered f

22、or sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Visual examination. Each neckerchief shall be examined for the defects listed below. 5.2.1 Defects. Any hole, cut, tear, needle chew; any visible mend, floats, broken or missing end or pick,

23、 clearly noticeable slubs or knots, loose stitching on hemmed edges. Fabric and/or shade not as specified. Any spot or stain clearly noticeable. Raw edges, open seams, thread ends not trimmed, loose tension resulting in loose seams or hem, end of hem stitching not backstitched or backtacked, color o

24、f thread not as specified, tight stitch tension, stitches break when normal strain applied. Selvages cut, torn, broken, scalloped, curled or folded. Any material defects, distorted parts, or poor workmanship. Finished neckerchief not pressed, gloss marks or scorched areas. Label missing, incorrect,

25、or illegible; not positioned or attached as specified; NSN bar code or UPC bar code label omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code label not visible on folded, packaged item; label causes damage to the item; any items not packaged in acco

26、rdance with the contract or order. 5.3 Dimensional examination. Measurements of the neckerchief shall be taken to verify dimensions listed in 3.1. 5.3.1 Dimensional defects. Measurements of item not as specified. 5.4 Acceptance criteria. Acceptance criteria shall be as specified in the contract or p

27、urchase order. 6. PACKAGING 6.1 Preservation, packing, and marking. The preservation, packing, and marking shall be as specified in the contract or purchase order. 7. NOTES 7.1 Source of Government documents. Copies of military and Federal documents are available from: Standardization Documents Orde

28、r Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 7.2 Source of non-Government documents. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-D-3775 Fabric Count of Woven Fabric Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5962

29、1 5ASTM-D-3776 Mass Per Unit Area (Weight) of Fabric (Applications for copies should be addressed to American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 61 Colorfastness to L

30、aundering, Home and Commercial: Accelerated AATCC-81 pH of Water Extract from Bleached Textiles AATCC-135 Dimensional Changes in Automatic Home Laundering AATCC-15 Colorfastness of Perspiration AATCC-16 Colorfastness to Light AATCC-8 Colorfastness to Crocking AATCC-20A Fiber Analysis (Applications f

31、or copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box12215, Research Triangle Park, NC 27709-2215.) Custodian: Preparing Activity: Navy - NU DLACT Project No. 8440-0238 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-