ASTM A659 A659M-12(2017) Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled.pdf
《ASTM A659 A659M-12(2017) Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled.pdf》由会员分享,可在线阅读,更多相关《ASTM A659 A659M-12(2017) Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A659/A659M 12 (Reapproved 2017)Standard Specification forCommercial Steel (CS), Sheet and Strip, Carbon (0.16Maximum to 0.25 Maximum Percent), Hot-Rolled1This standard is issued under the fixed designation A659/A659M; the number immediately following the designation indicates the yearof
2、 original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Depart
3、ment of Defense.1. Scope*1.1 This specification covers hot-rolled carbon steel (CS)sheet and strip, in coils and cut lengths, in which the maximumof the specified carbon range is over 0.15 and not over 0.25 %and the maximum of the specified manganese range is not over0.90 %. This material is ordered
4、 to chemical composition.1.2 This specification is not applicable to the steels coveredby Specification A635/A635M.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsyste
5、m shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for th
6、eDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A568/A568M Specification for Steel, Sheet, Carbon,Structural, and High-Strength, Low-Alloy, Hot-Rolled and
7、Cold-Rolled, General Requirements forA635/A635M Specification for Steel, Sheet and Strip,Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon,Structural, High-Strength Low-Alloy, and High-StrengthLow-Alloy with Improved Formability, General Require-ments forA749/A749M Specification for Steel, Strip, Car
8、bon andHigh-Strength, Low-Alloy, Hot-Rolled, General Require-ments forE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.2 Society of Automotive Engineers Standard:3J 1086 Numbering Metals and Alloys3. Ordering Information3.1 It is the purchasers responsibility to sp
9、ecify in thepurchase order all ordering information necessary to purchasethe needed material. Examples of such information include butare not limited to the following:3.1.1 ASTM specification number and year of issue,3.1.2 Name of material (hot-rolled commercial steel (CS)sheet, or hot-rolled commer
10、cial steel (CS) strip),3.1.3 Grade designation or chemical composition, or both,3.1.4 Copper-bearing steel (if required),3.1.5 Condition (as-rolled, pickled, or blast cleaned) (see4.1),3.1.5.1 Material to this specification is furnished in thehot-rolled condition. Pickled (or blast cleaned) must be
11、speci-fied if required,3.1.6 Oiling (see 7.2),3.1.7 Edges (see 7.1),3.1.8 Dimensions (thickness, width, and whether cut lengthsor coils),NOTE 1Not all producers are capable of meeting all of the limitationsof the thickness tolerance tables in Specification A568/A568M. Thepurchaser should contact the
12、 producer regarding possible limitations priorto placing an order.3.1.9 Coil size (must include inside diameter, outsidediameter, and maximum mass),3.1.10 Quantity,3.1.11 Application (show part identification anddescription),3.1.12 Cast or heat analysis report (request, if required),3.1.13 Special r
13、equirements (if required).1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.19 on Steel Sheet and Strip.Current edition approved Sept. 1, 2017. Published September 2017. Originallyapprov
14、ed in 1972. Last previous edition approved in 2012 as A659/A659M 12.DOI: 10.1520/A0659_A0659M-12R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Do
15、cument Summary page onthe ASTM website.3Available from Society of Automotive Engineers (SAE), 400 CommonwealthDr., Warrendale, PA 15096-0001, http:/www.sae.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Cons
16、hohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Or
17、ganization Technical Barriers to Trade (TBT) Committee.13.1.13.1 When the purchaser requires thickness tolerancesfor 3/8 in. 10 mm minimum edge distance (see Supplemen-tary Requirement in Specification A568/A568M), this require-ment shall be specified in the purchase order or contract.NOTE 2A typica
18、l ordering description is as follows:“ASTM A659-XX or A659M-XX, Hot-Rolled Commercial Steel (CS)Sheet, Grade 1017, Pickled and Oiled, Cut Edge, 0.075 by 36 in. or 1.85by 900 mm, by coil, ID 24 in., OD 48 in., max weight 11 250 lb max orID 600 mm, OD 1200 mm, max, weight 7500 kg, max, 100 000 lb or 4
19、5000 kg for Part No. 6509, Shelf Leg, Cast or heat analysis reportrequired.”4. Materials and Manufacture4.1 ConditionUnless otherwise specified, the material isfurnished in the as-rolled condition (not annealed or pickled).5. Chemical Composition5.1 The Cast or Heat Analysis of the steel shall confo
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTM A659 A659M-122017 Standard Specification for Commercial Steel CS Sheet and Strip Carbon 0.16 A659M

链接地址:http://www.mydoc123.com/p-349525.html