ASTM E1456 - 08 Standard Specification for Caustic Potash; Solid (Potassium Hydroxide; Solid) (Withdrawn 2017).pdf

《ASTM E1456 - 08 Standard Specification for Caustic Potash; Solid (Potassium Hydroxide; Solid) (Withdrawn 2017).pdf》由会员分享，可在线阅读，更多相关《ASTM E1456 - 08 Standard Specification for Caustic Potash; Solid (Potassium Hydroxide; Solid) (Withdrawn 2017).pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1456 08Standard Specification forCaustic Potash; Solid (Potassium Hydroxide; Solid)1This standard is issued under the fixed designation E1456; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers two grades of solid

3、 causticpotash, 85 % and 90 %.1.2 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.1.3 Review the current Materials Safety Data Sheets(MSDS) for detailed information concerning toxicity, first aidprocedures, handling and safety prec

4、autions.1.4 The following safety hazards caveat pertains only to thetest methods portion, Section 6: This standard does not purportto address all of the safety concerns, if any, associated with itsuse. It is the responsibility of the user of this standard toestablish appropriate safety and health pr

5、actices and deter-mine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E291 Test Methods for Chemical Analysis of Caustic Sodaand Caustic Potash (Sodium Hydroxide and PotassiumHydroxide)E300 Practice for Sampling Industrial Chemicals3. Classificati

6、on3.1 Type ICaustic potash, solid form, 85 % potassiumhydroxide.3.2 Type IICaustic potash, solid form, 90 % potassiumhydroxide.4. Chemical Requirements4.1 Caustic potash shall conform to the chemical require-ments listed in Table 1.5. Sampling5.1 Caustic potash shall be sampled in accordance with th

7、eappropriate sections of Practice E300 for solid chemicals.6. Test Methods6.1 Analyze caustic potash in accordance with the appli-cable sections of Test Methods E291.7. Keywords7.1 caustic potash; potassium hydroxide; solid1This specification is under the jurisdiction of ASTM Committee D16 onAromati

8、c Hydrocarbons and Related Chemicals and is the direct responsibility ofSubcommittee D16.15 on Industrial and Specialty General Standards.Current edition approved April 1, 2008. Published May 2008. Originallyapproved in 1992. Last previous edition approved in 2002 as E1456 97 (2002).DOI: 10.1520/E14

9、56-08.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of thi

10、s standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesNOTICE: This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International (www.astm.org) for the latest information1SUMMARY OF CHANG

11、ESCommittee E15 has identified the location of selected changes to this standard since the last issue(E145697(2002) that may impact the use of this standard.(1) Updated units of measure to comply with the InternationalSystem of Units (SI).(2) Added subsection to Scope stating that the SI units are t

12、oconsidered standard.(3) Added Summary of Changes section.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such pate

13、nt rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited eith

14、er for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair h

15、earing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standa

16、rd may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Chemical RequirementsChemical Type I Type IITotal alkalinity as KOH, % by mass (weight) 85.0 min 90.0 minK2CO3, % by mass (weight) 0.8 max 0.8 maxKCl, g/g (ppm) 150 max 150 maxFe, g/g (ppm) 5.0 max 5.0 maxE1456 082