ASTM D5869D5869M-07A(2018)e1 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials.pdf

《ASTM D5869D5869M-07A(2018)e1 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials.pdf》由会员分享，可在线阅读，更多相关《ASTM D5869D5869M-07A(2018)e1 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D5869/D5869M 07a (Reapproved 2018)1Standard Practice forDark Oven Heat Exposure of Roofing and WaterproofingMaterials1This standard is issued under the fixed designation D5869/D5869M; the number immediately following the designation indicates theyear of original adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEUnits information was editorially corrected in January 2018.1. Scope1.1 This practice establishes a

3、 procedure and conditions oftemperature and time for heat exposure of roofing and water-proofing materials and systems in the presence of air.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equiva

4、lents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of

5、this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the D

6、ecision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1079 Terminology Relating to Roofing and

7、 WaterproofingD1566 Terminology Relating to RubberE145 Specification for Gravity-Convection and Forced-Ventilation OvensE230/E230M Specification for Temperature-ElectromotiveForce (emf) Tables for Standardized ThermocouplesE1137/E1137M Specification for Industrial Platinum Resis-tance ThermometersE2

8、251 Specification for Liquid-in-Glass ASTM Thermom-eters with Low-Hazard Precision Liquids3. Terminology3.1 DefinitionsFor definitions of terms used in thispractice, refer to Terminologies D883, D1079, and D1566.4. Summary of Practice4.1 Specimens of roofing and waterproofing materials areexposed to

9、 heat in a dark forced-ventilation oven at a specifiedelevated temperature for a known period of time.4.2 This practice specifies an exposure temperature of 70 63C 158 6 5F in a forced-ventilation oven.4.3 This practice permits the selection of the duration ofheat exposure from three specified time

10、periods, which are 35,90, and 180 6 0.25 consecutive days. The duration selectedmust be included in any report of results obtained by using thispractice.NOTE 1The time period to be used should be specified in any standardthat refers to this practice. European standards for polymer-modifiedbituminous

11、 materials specify 180 days at 70C. For research purposes,selection of other time periods and temperatures are permitted, providedthat the precise duration is stated in any report of results.4.4 This practice is also used to condition test specimens fortime periods much shorter than 35 days for the

12、purpose ofconditioning material before testing. When used for thispurpose, the shorter conditioning time shall be specified in anyreport of test results.5. Significance and Use5.1 Roofing and waterproofing materials and systems un-dergo changes in physical properties as a result of beingsubjected to

13、 heat. They also undergo changes in physicalproperties as they age in service. Since service conditions varywidely, any relationship between changes observed in thispractice and changes in service must be established by the userof this practice.1This practice is under the jurisdiction ofASTM Committ

14、ee D08 on Roofing andWaterproofing and is the direct responsibility of Subcommittee D08.02 on SteepRoofing Products and Assemblies.Current edition approved Jan. 1, 2018. Published January 2018. Originallyapproved in 1995. Last previous edition approved in 2013 as D5869 07a (2013).DOI: 10.1520/D5869_

15、D5869M-07AR18E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbo

16、r Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendatio

17、ns issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16. Apparatus6.1 OvenThe oven shall have forced ventilation, shall beelectrically heated, and shall conform to the requirements ofSpecification E145, Type IIB. The oven shall be of sufficientsize to accommodate the

18、 size and number of specimensselected by the user of this practice.6.2 ThermometerThe thermometer shall be an ASTMthermometer, conforming to the requirements for thermometerS12C (or S12F) in accordance with Specification E2251.Asanalternate, any other thermometric device used shall be at least:(1) o

19、f equal accuracy to that of the thermometer specified inSpecification E2251,(2) capable of indicating temperature towithin 1C 2F, and (3) stable to within 1C 2F for theduration of the exposure.6.2.1 When used, platinum resistance thermometers shall bein accordance with the requirements of Specificat

20、ion E1137/E1137M.6.2.2 When used, thermocouples shall be in accordancewith the requirements of Specification E230/E230M.7. Specimens7.1 The number, geometry, and size of specimens shall bedetermined by the user of this practice.8. Heat Exposure8.1 Expose the specimens in a forced-ventilation oven at

21、 706 3C 158 6 5F .8.2 The specimens shall be supported in the oven onshelves, plates, or other containers appropriate to the specimenbeing studied. Specimens shall be separated on shelves toallow free access of air. The specimen orientation, vertical,horizontal, and so forth, shall be determined by

22、the user of thispractice.8.3 The duration of exposure of the specimens to the heatshall be selected by the user of this practice from the followingoptions: (1)356 0.25 consecutive days; (2)906 0.25consecutive days; or (3) 180 6 0.25 consecutive days. (Seealso 4.4.)9. Report9.1 Report the following i

23、nformation:9.1.1 State the geometry of the specimen, orientation duringthe exposure, and nature of support.9.1.2 Report the duration of exposure to the heat.10. Keywords10.1 dark oven exposure; heat exposure; roofing andwaterproofing materialsASTM International takes no position respecting the valid

24、ity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subje

25、ct to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquart

26、ers. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard

27、 is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 07a (2018)12