ASTM D2226-93(2018) Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use.pdf

《ASTM D2226-93(2018) Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use.pdf》由会员分享，可在线阅读，更多相关《ASTM D2226-93(2018) Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2226 93 (Reapproved 2018)Standard Classification forVarious Types of Petroleum Oils for Rubber CompoundingUse1This standard is issued under the fixed designation D2226; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,

2、the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This classification is intended to establish classificationand test methods for certain types of oil used

3、in extending andprocessing styrene-butadiene rubbers (SBR) and butadienerubbers (BR). Its purpose is for classification only and not forspecification.1.2 This standard may involve hazardous materials,operations, and equipment. This standard does not purport toaddress all of the safety concerns, if a

4、ny, associated with itsuse. It is the responsibility of the user of this standard toestablish appropriate safety, health, and environmental prac-tices and determine the applicability of regulatory limitationsprior to use.1.3 This international standard was developed in accor-dance with international

5、ly recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D88 Test Meth

6、od for Saybolt ViscosityD92 Test Method for Flash and Fire Points by ClevelandOpen Cup TesterD97 Test Method for Pour Point of Petroleum ProductsD445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids (and Calculation of Dynamic Viscos-ity)D611 Test Methods for Aniline Point and Mi

7、xed AnilinePoint of Petroleum Products and Hydrocarbon SolventsD972 Test Method for Evaporation Loss of LubricatingGreases and OilsD974 Test Method for Acid and Base Number by Color-Indicator TitrationD1298 Test Method for Density, Relative Density, or APIGravity of Crude Petroleum and Liquid Petrol

8、eum Prod-ucts by Hydrometer MethodD1500 Test Method for ASTM Color of Petroleum Products(ASTM Color Scale)D2007 Test Method for Characteristic Groups in RubberExtender and Processing Oils and Other Petroleum-Derived Oils by the Clay-Gel Absorption Chromato-graphic MethodD2008 Test Method for Ultravi

9、olet Absorbance and Absorp-tivity of Petroleum ProductsD2501 Test Method for Calculation of Viscosity-GravityConstant (VGC) of Petroleum OilsD2887 Test Method for Boiling Range Distribution of Pe-troleum Fractions by Gas Chromatography2.2 International Institute of Synthetic Rubber Producers:The Syn

10、thetic Rubber Manual, 19th Ed., 201533. Significance and Use3.1 The composition of the oil in rubber compounds has alarge effect on the characteristics and use of the compounds.This classification divides the oils into broad categories fordescriptive purposes.4. Numbering System4.1 The description a

11、nd numbers of polymers and laticesincluding oil extended polymers outlined are in a brochureissued and updated by the International Institute of SyntheticRubber Producers, Inc. Notes of explanation to cover differ-ences in nomenclature or variations in classifications fromASTM practices are incorpor

12、ated as necessary.5. Basis of Classification5.1 Classification of petroleum oils as used for extendingand processing styrene-butadiene rubbers (SBR) and butadienerubbers (BR) is given in Table 1. Classification is based onresults obtained in accordance with Test Method D2007 andTest Method D2501.1Th

13、is classification is under the jurisdiction of ASTM Committee D11 onRubber and Rubber-like Materials and is the direct responsibility of SubcommitteeD11.20 on Compounding Materials and Procedures.Current edition approved Feb. 1, 2018. Published February 2018. Originallyapproved in 1963. Last previou

14、s edition approved in 2012 as D2226 93 (2012).DOI: 10.1520/D2226-93R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe AST

15、M website.3Available from International Institute of Synthetic Rubber Producers, Inc., 2077S. Gessner Rd., Suite 133, Houston, TX 77063.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accord

16、ance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16. Test Methods6.1 The types of p

17、etroleum oils listed in Table 1 may befurther characterized by testing in accordance with Test Meth-ods D88, D92, D97, D445, D611, D972, D974, D1298, D1500,D2008, and D2887.7. Keywords7.1 extending oils; petroleum oils; processing oilsASTM International takes no position respecting the validity of a

18、ny patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to re

19、vision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. You

20、r comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copy

21、righted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.or

22、g (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Classification of Oil TypesTypesAsphaltenes,max, %APolarCompounds,max, %Satu

23、ratedHydrocarbons, %101 0.75 25 20 max102 0.5 12 20.1 to 35103 0.3 6 35.1 to 65104B0.1 1 65 minAPentane-insoluble materials as determined by Test Method D2007.BType 104 oils are further classified into two subtypes 104A and 104B for SBRpolymers only. Type 104B oils are those that have a viscosity-gr

24、avity constant of0.820 maximum (Test Method D2501). Type 104A oils are those that have aviscosity-gravity constant greater than 0.820 (Test Method D2501). It is recognizedthat certain Type 104 oils may not be satisfactorily classified for polymers otherthan SBR by this subclassification.D2226 93 (2018)2