EN 13476-1-2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride.pdf

《EN 13476-1-2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride.pdf》由会员分享，可在线阅读，更多相关《EN 13476-1-2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)Part 1: General requirem

2、ents and performance characteristicsBS EN 134761:2018National forewordThis British Standard is the UK implementation of EN 134761:2018. It supersedes BS EN 134761:2007, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/88/1, Plastics piping for nonpr

3、essure applications.A list of organizations represented on this committee can be obtained on request to its secretary.The responsible UK committee gives the following advice concerning the scope and contents of EN 134761:2018. Attention is drawn to the scope of this standard, which, together with BS

4、 EN 134762:2018 and BS EN 134763:2018, is applicable to structuredwall plastic piping systems made of unplasticized poly(vinyl chloride) (PVCU), polypropylene (PP) or polyethylene (PE) with any additives needed to facilitate the manufacture of components conforming to this standard. Multilayer compo

5、site pipes with an intermediate layer of metal; reinforced pipes; and pipes made of polymers other than PVCU, PP or PE are not covered by the scope of this standard. The test methods and performance criteria are not applicable to these types of pipe. Recycled material: The use of recycled or reproce

6、ssed materials is encouraged in the UK. However, their use should be strictly in accordance with this standard. Interchangeability: This standard does not guarantee interchangeability between manufacturers. It is strongly advised that users specify the bore series of pipes (DN/ID) as specified in BS

7、 EN 134762:2018 and BS EN 134763:2018 to maximize the hydraulic performance of these products. Initial ring stiffness: The BS EN 13476 series specifies four nominal ring stiffness classes (SN): SN2, SN4, SN8 and SN16. DN 500: SN4, SN8 or SN16; DN 500: SN2, SN4, SN8 or SN16.From the viewpoint of inst

8、allation, SN4 and SN8 are the traditionally recommended classes used in the UK for water company adopted sewers and are to be used if the system is to be installed in accordance with BS EN 752:2017 or BS EN 1610:2015 to achieve the intended resistance to longterm deformation. If use of the SN2 class

9、 of pipe or fittings is intended, the installation should first be subject to a structural design soil load / traffic load calculation and the installation technique modified to suit the results of that calculation. The appropriate calculation method is given in the National Annex NA to BS EN 12951.

10、 The shortterm E modulus for the material should be taken from Table A.1 of BS EN 134761:2018. The longterm value of E should be taken as the shortterm value divided by the creep ratio. The creep ratio is derived from the tests specified in the Mechanical characteristics section of BS EN 134762:2018

11、 or BS EN 134763:2018 as appropriate. Impact: Annex G of BS EN 134762:2018 and BS EN 134763:2018 details an impact resistance test at 23C. This is the preferred test in the UK. Annex H therefore becomes informative in the UK.BRITISH STANDARDBS EN 134761:2018This publication does not purport to inclu

12、de all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 91093 7ICS 93.030; 23.040.20Compliance with a British Standard cannot confer immunity from legal obligations.

13、This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARD BS EN 134761:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13476-1April 2018ICS 23.040.01; 9

14、3.030 Supersedes EN 134761:2007EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN 134761:2018: EAll rights of exploitation in any form and by any means reserved worldw

15、ide for CEN national MembersPlastics piping systems for nonpressure underground drainage and sewerage Structuredwall piping systems of unplasticized poly(vinyl chloride) (PVCU), polypropylene (PP) and polyethylene (PE) Part 1:General requirements and performance characteristicsSystmes de canalisatio

16、ns en plastique pour les branchements et les collecteurs dassainissements sans pression enterrs Systmes de canalisations parois structures en poly(chlorure de vinyle) non plastifi (PVCU), polypropylne (PP) et polythylne (PE) Partie 1: Exigences gnrales et caractristiques de performanceKunststoffRohr

17、leitungssysteme fr erdverlegte drucklose Abwasserkanle und leitungen Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVCU), Polypropylen (PP) und Polyethylen (PE) Teil 1: Allgemeine Anforderungen und LeistungsmerkmaleThis European Standard was approved by CEN on

18、8 February 2018.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be

19、 obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

20、 CENCENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irelan

21、d, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 13476-1:2018European foreword iiiIntroduction v1 Scope . 12 Normative references 13 Terms and definition

22、s . 23.1 Terms and definitions . 23.1.1 General definitions . 23.1.2 Geometrical definitions 33.2 Symbols and abbreviations 44 Material 54.1 General . 54.2 Utilization of nonvirgin material . 54.3 Sealing ring retaining components 54.4 Sealing rings 54.5 Fused or welded joints . 54.6 Adhesives for P

23、VCU . 55 Designation of wall construction . 56 Appearance and colour 56.1 Appearance 56.2 Colour 67 Geometrical characteristics 68 Types of fittings . 68.1 General . 68.2 Design length of fittings 89 System performance related test methods and characteristics 810 Marking, general 1010.1 Presentation

24、 . 1010.2 Marking process 1010.3 Size 10Annex A (informative) Characteristics of PVC-U, PP and PE pipes and fittings .11Annex B (informative) Structural design 13Annex C (informative) Designation of pipes and corresponding fittings 14Annex D (informative) Guidance in cleaning plastics pipes 15Biblio

25、graphy .19ii ISO 2018 All rights reservedContents PageBS EN 134761:2018EN 13476-1:2018European forewordThis document (EN 134761:2018) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.This European Standard shal

26、l be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2018, and conflicting national standards shall be withdrawn at the latest by October 2018.Attention is drawn to the possibility that some of the elements of this docum

27、ent may be the subject of patent rights. CEN not be held responsible for identifying any or all such patent rights.This document supersedes EN 134761:2007.The main changes with respect to the previous edition are listed below:a) updating of references in Clause 2, Table 2 and Bibliography;b) deletio

28、n of Note 3 (Scope);c) definition fabricated fitting changed (3.1.1.3);d) clarification requirements sealing ring (4.4);e) extension of nominal sizes range (Table 1, Table 2);f) substitute “DURABILITY” Table 2;g) new reference for hydraulic roughness (A.5);h) text updated and new reference (Annex B)

29、;i) adhesives PVCU added (4.6);j) saddle branches deleted (8.1);k) updated with new CEN template (entire document).This standard is a part of a System Standard for plastics piping systems of particular materials for specified applications. There are a number of such System Standards.System Standards

30、 are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organization for Standardization (ISO).They are supported by separate standards on test methods to which referen

31、ces are made throughout the System Standard.The System Standards are consistent with general standards on functional requirements and on recommended practice for installation.EN 13476 consists of the following parts under the general title “Plastics piping systems for nonpressure underground drainag

32、e and sewerage Structuredwall piping systems of unplasticized poly(vinyl chloride) (PVCU), polypropylene (PP) and polyethylene (PE)”:Part 1: General requirements and performance characteristics (this standard);Part 2: Specifications for pipes and fittings with smooth internal and external surface an

33、d the system, Type A;Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B; ISO 2018 All rights reserved iiiBS EN 134761:2018EN 13476-1:2018Part 4: Assessment of conformity.National standards specifically for pipes and fittings for th

34、e transport of surface water are not considered to be conflicting with this standard and may thus be allowed to coexist.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,

35、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Swi

36、tzerland, Turkey and the United Kingdom.iv ISO 2018 All rights reservedBS EN 134761:2018EN 13476-1:2018IntroductionDue to the variety in materials, pipe constructions, application areas and classes, several combinations are possible.The purchaser or specifier may select between these possibilities b

37、y designating the pipe and fitting he or she prefers to use for each case, as described in Annex C “Designation of pipes and corresponding fittings”, taking into account any particular requirements and relevant national regulations and installation practices or codes. ISO 2018 All rights reserved vB

38、S EN 134761:2018This page deliberately left blankPlastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: General requirements and performance characteri

39、stics1 ScopeThis European Standard, together with EN 134762 and EN 134763, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVCU), polypropylene (PP) and polyethylene (PE) structuredwall piping systems that are to be u

40、sed for nonpressure underground drainage and sewerage systems.This standard is applicable to:a) structuredwall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by “U”;b) structuredwall pipes and fittings, which are

41、to be used buried in ground both outside (application area code “U”) and within a building structure (application area code “D”); reflected in the marking of products by “UD”.In conjunction with EN 134762 and EN 134763, it is applicable to structuredwall pipes and fittings with or without an integra

42、l socket with elastomeric ring seal joints, as well as welded and fused joints.This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options.EN 134762 and EN 134763 specify material ch

43、aracteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B.This standard, together with EN 134762 and EN 134763, covers a range of pipe an

44、d fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours.NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements

45、 and any relevant national regulations and installation practices or codes.NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in Clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint

46、dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editi

47、on cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 13476-1:2018 ISO 2018 All rights reserved 1BS EN 134761:2018EN 13476-1:2018EN 6811, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage a

48、pplications Part 1: Vulcanized rubberEN 6812, Elastomeric Seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomersEN 6814, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 4: C

49、ast polyurethane sealing elementsEN 134762:2018, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type AEN 134763:2018, Plastics piping systems for non-pressure underground drainage and sewer