ISO 9701-1994 Wrist and pocket watches - Fitting diameters for hour minute and second hands《手表及怀表 时针、分针和秒针的配合直径》.pdf

《ISO 9701-1994 Wrist and pocket watches - Fitting diameters for hour minute and second hands《手表及怀表 时针、分针和秒针的配合直径》.pdf》由会员分享，可在线阅读，更多相关《ISO 9701-1994 Wrist and pocket watches - Fitting diameters for hour minute and second hands《手表及怀表 时针、分针和秒针的配合直径》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD IS0 9701 First edition 1994-09-I 5 Wrist and pocket watches - Fitting diameters for hour, minute and second hands Montres-bracelets et montres de poche - Diamktres dajustemen t des aiguilles dheures, de minutes et de secondes Reference number IS0 9701:1994(E) Copyright Interna

2、tional Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 9701:1994(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (

3、IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, go

4、vernmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to

5、the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 9701 was prepared by Technical Committee lSO/TC 114, /-/orology, Subcommittee SC 7, Overall dimensions. 0 IS0 1994 All rights rese

6、rved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. lnternational Organization for Standardization Case Postale 56 l C

7、H-1211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD 0 IS0 IS0 9701:1994(E) Wrist and pocket wa

8、tches - Fitting diameters for hour, minute and second hands 1 Scope This International Standard specifies the fitting diam- eters of hour, minute and second hands for wrist and pocket watches. 2 Definitions For the purposes of this International Standard, the following definitions apply. 2.1 fitting

9、 diameters of hour wheel, cannon pinion and second wheel: External diameters of hour wheel, cannon pinion and second wheel. 2.2 fitting diameters of hour, minute and second hands: Internal diameters of mountings for hour, minute and second hands. 3 Dimensions dl DI Figure 1 - Fitting diameters of ho

10、ur wheel, ad, and hour hand, rrD, d2 D2 t-i The dimensions shall be as given in table 1 (see fig- Figure 2 - Fitting diameters of cannon pinion, ures 1 to 3). 04, and minute hand, oD, Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo repr

11、oduction or networking permitted without license from IHS-,-,-IS0 9701:1994(E) Figure 3 - Fitting diameters of second wheel, 04, and second hand, CD, Table 1 - Fitting diameters of hour, minute and second hands Dimensions in millimetres 0d, and 0D, 04 and 00, 04 and 0D, Basic Auxiliary Basic Auxilia

12、ry Basic Auxiliary 0,70 0,30 0,14 0,80 0,40 0,16 0,90 0,45 0,17 1 ,oo 0,50 0,18 I,05 0,55 0,20 I,10 0,60 0,22 I,20 0,65 0,25 1,30 0,70 0,30 I,40 0,80 0,35 I,50 0,85 0,40 I,60 1,70 0,90 I,80 1 ,oo I,90 1,lO 2,00 I,20 2,20 I,30 2,50 I,40 I,50 Copyright International Organization for Standardization Pr

13、ovided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitt

14、ed without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright Internatio

15、nal Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 9701:1994(E) KS 39.040.10 Descriptors: horological industry, time measuring instruments, watches, wrist watches, horological components, clock hands, diameters, fitting. Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-