ISO 7612-2009 Diesel engines - Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems - Mounting dimens.pdf

《ISO 7612-2009 Diesel engines - Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems - Mounting dimens.pdf》由会员分享，可在线阅读，更多相关《ISO 7612-2009 Diesel engines - Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems - Mounting dimens.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 7612:2009(E) ISO 2009INTERNATIONAL STANDARD ISO 7612 Fourth edition 2009-10-15 Diesel engines Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems Mounting dimensions Moteurs diesels Pompes dinjection en ligne fixation

2、par base plane et pompes dalimentation haute pression pour systmes dinjection de carburant rampe commune Dimensions de montage ISO 7612:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be

3、 edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is

4、 a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO membe

5、r bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by

6、 any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-ma

7、il copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedISO 7612:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepa

8、ring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in l

9、iaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task o

10、f technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention i

11、s drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7612 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 7, Injection equipment an

12、d filters for use on road vehicles. This fourth edition cancels and replaces the third edition (ISO 7612:2006), which has been technically revised. INTERNATIONAL STANDARD ISO 7612:2009(E) ISO 2009 All rights reserved 1Diesel engines Base-mounted in-line fuel injection pumps and high-pressure supply

13、pumps for common rail fuel injection systems Mounting dimensions 1 Scope This International Standard specifies dimensional requirements for base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems for diesel (compression-ignition) engines. 2 Dim

14、ensions and tolerances Dimensions and tolerances are given in Figures 1 to 8 and Tables 1 to 4. Dimensions and tolerances not given in this International Standard are left to the manufacturers choice. Dimensions in millimetres See Table 1 for other dimensions. Figure 1 Base-mounted in-line fuel inje

15、ction pump Type 1 ISO 7612:2009(E) 2 ISO 2009 All rights reservedTable 1 Base-mounted in-line fuel injection pump Type 1 Number of cylinders d anom. mm A ref. mm 4 140 6 210 8 280 10 353 12 25 or 30 423 aCorresponds to dimension d in ISO 6519. Dimensions in millimetres See Table 2 for other dimensio

16、ns. a4 or 6 holes. Figure 2 Base-mounted in-line fuel injection pump Type 2 Table 2 Base-mounted in-line fuel injection pump Type 2 Number of cylinders d anom. mm A ref. mm B ref. mm Number of fixing holes 4 133,5 4 6 206 4 8 25 or 30 278,5 139,25 6 aCorresponds to dimension d in ISO 6519. ISO 7612:

17、2009(E) ISO 2009 All rights reserved 3Dimensions in millimetres See Table 3 for other dimensions. Figure 3 Base-mounted in-line fuel injection pump Type 3 Table 3 Base-mounted in-line fuel injection pump Type 3 Number of cylinders d anom. mm A ref. mm B 0,25 mm 4 154 6 218 8 25 or 30 302 151 aCorres

18、ponds to dimension d in ISO 6519. ISO 7612:2009(E) 4 ISO 2009 All rights reservedDimensions in millimetres See Table 4 for other dimensions. Figure 4 Base-mounted in-line fuel injection pump Type 4 Table 4 Base-mounted in-line fuel injection pump Type 4 Number of cylinders d anom. mm A ref. mm 4 132

19、 6 202 8 30 or 35 272 aCorresponds to dimension d in ISO 6519. ISO 7612:2009(E) ISO 2009 All rights reserved 5Dimensions in millimetres aCorresponds to dimension d in ISO 6519. Figure 5 Base-mounted, two cylinder, high-pressure supply pump Type 5 ISO 7612:2009(E) 6 ISO 2009 All rights reservedDimens

20、ions in millimetres aCorresponds to dimension d in ISO 6519. Figure 6 Base-mounted, two cylinder, high-pressure supply pump Type 6 ISO 7612:2009(E) ISO 2009 All rights reserved 7Dimensions in millimetres aCorresponds to dimension d in ISO 6519. Figure 7 Base-mounted, two cylinder, high-pressure supp

21、ly pump Type 7 ISO 7612:2009(E) 8 ISO 2009 All rights reservedDimensions in millimetres aCorresponds to dimension d in ISO 6519. Figure 8 Base-mounted, three cylinder, high-pressure supply pump Type 8 ISO 7612:2009(E) ISO 2009 All rights reserved 9Bibliography 1 ISO 6519, Diesel engines Fuel injecti

22、on pumps Tapers for shaft ends and hubs 2 ISO 7299-1, Diesel engines End-mounting flanges for pumps Part 1: Fuel injection pumps 3 ISO 7299-2, Diesel engines End-mounting flanges for pumps Part 2: High-pressure supply pumps for common rail fuel injection systems 4 ISO 7879, Diesel engines Cradle-mounted in-line fuel injection pumps Mounting dimensions ISO 7612:2009(E) ICS 43.060.40 Price based on 9 pages ISO 2009 All rights reserved