ASTM F3343-2019 Standard Consumer Safety Specification for Infant Bathers.pdf

《ASTM F3343-2019 Standard Consumer Safety Specification for Infant Bathers.pdf》由会员分享，可在线阅读，更多相关《ASTM F3343-2019 Standard Consumer Safety Specification for Infant Bathers.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F3343 19Standard Consumer Safety Specification forInfant Bathers1This standard is issued under the fixed designation F3343; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenth

2、eses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification is intended to address certain incidents associated with the useof infant bathers. The U.S. Consumer Product Safety C

3、ommission (CPSC) identified drowningincidents which generally involved infant bathers being used in adult tubs containing water and leftunattended by their caregiver. The CPSC also identified non-fatal incidents related to collapsing of theinfant bather which generally happened when the caregiver at

4、tempted to transport the occupant whilein the infant bather. This specification does not address incidents in which infant bathers are abusedor unreasonably misused. This consumer safety specification is written within the current state-of-the-art product technology. It is intended that this specifi

5、cation will be updated whenever substantiveinformation becomes available and known to ASTM which necessitates additional requirements orjustifies the revision of existing requirements.1. Scope1.1 This consumer safety specification establishes perfor-mance requirements, test methods, and labeling req

6、uirementsto promote the safe use of infant bathers.1.2 This consumer safety specification is intended to reducethe risk of death and minimize injury to infants resulting fromuse and reasonably foreseeable misuse or abuse of infantbathers.1.3 No infant bather produced after the approval date of thisc

7、onsumer safety specification shall, either by label or othermeans, indicate compliance with this specification unless itconforms to all requirements contained herein.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions t

8、o SI units that are provided for information onlyand are not considered standard.1.5 The following precautionary caveat pertains only to thetest method portion, Section 7, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It i

9、s the responsibility of the userof this standard to establish appropriate safety, health, andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standa

10、rd-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D1683/D1683M Test Method for Failure in Sewn Se

11、ams ofWoven FabricsD3359 Test Methods for Rating Adhesion by Tape TestF963 Consumer Safety Specification for Toy SafetyF2088 Consumer Safety Specification for Infant SwingsF2167 Consumer Safety Specification for Infant BouncerSeatsF2670 Consumer Safety Specification for Infant Bath Tubs2.2 Federal S

12、tandards:316 CFR 1303 Ban of Lead-Containing Paint and CertainConsumer Products Bearing Lead Containing Paint16 CFR 1500 Federal Hazardous Substances Act Regula-tions16 CFR 1500.48 Technical Requirements for Determining aSharp Point in Toys and Other Articles Intended for Use1This consumer safety sp

13、ecification is under the jurisdiction of ASTM Commit-tee F15 on Consumer Products and is the direct responsibility of SubcommitteeF15.20 on Bath Seats.Current edition approved Feb. 1, 2019. Published February 2019. DOI: 10.1520/F3343-19.2For referenced ASTM standards, visit the ASTM website, www.ast

14、m.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Government Printing Office, Superintendent ofDocuments, 732 N. Capitol St., NW, Washington, DC 20401-00

15、01, http:/www.access.gpo.gov.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principle

16、s for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1by Children Under 8 Years of Age16 CFR 1500.49 Technical Requirements for Determining aSharp Metal or Glass Edge in Toys and Other ArticlesI

17、ntended for Use by Children Under 8 Years of Age16 CFR 1501 Method for Identifying Toys and Other Ar-ticles Intended for Use by Children Under 3 Years of AgeWhich Present Choking, Aspiration, or Ingestion HazardsBecause of Small PartsConsumer Product Safety Improvement Act2.3 ANSI Standards:4ANSI Z5

18、35.1 Safety ColorsANSI Z535.4 Product Safety Signs and LabelsANSI Z535.6 Product Safety Information in ProductManuals, Instructions, and Other Collateral Materials3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 conspicuous, adjvisible, when the occupant is in theproduct and th

19、e product is in any manufacturers recommendeduse position(s), to a person positioned near the product at anyone position around the product, but not necessarily visiblefrom all positions.3.1.2 double action release system, na mechanism requir-ing either two consecutive actions, the first of which mu

20、st bemaintained while the second is carried out, or two separate andindependent simultaneous actions to fully release.3.1.3 grasping point, ntwo-inch wide section of the framecentered at the mid-point of the opposite sides or ends of theproduct normally associated with lifting.3.1.3.1 DiscussionThis

21、 could be at the headrest/backrestand footrest or on the left and right sides of the product.3.1.4 infant bather, na stand-alone product intended toprovide support for an occupant who cannot sit uprightunassisted (approximately 0 to 6 months) in a recliningposition during bathing by a caregiver but

22、not intended toretain water.3.1.4.1 DiscussionGenerally, an infant bather is used in anadult tub or in or next to a sink.3.1.5 manufacturers recommended use position(s), nanyposition that is presented as a normal, allowable, or acceptableconfiguration for the use of the product by the manufacturer i

23、nany descriptive or instructional literature.3.1.5.1 DiscussionThis specifically excludes positionswhich the manufacturer shows in a like manner in its literatureto be unacceptable, unsafe, or not recommended.3.1.6 non-paper label, nany label material, such as plasticor metal, that either will not t

24、ear without the aid of tools ortears leaving a sharply defined edge or labels made of fabric.3.1.7 occupant, nthat individual who is in an infant batherin one of the manufacturers recommended use positions.3.1.8 paper label, nany label material that tears withoutthe aid of tools and leaves a fibrous

25、 edge.3.1.9 principal display panel, nthat part of the productspackage that is most likely to be displayed, presented, shown,or examined under normal or customary conditions of displayfor retail sale.3.1.10 protective component, nany component used forprotection from sharp edges, points, or entrapme

26、nt of fingers ortoes.3.1.10.1 DiscussionExamples of protective componentsinclude caps, sleeves, and plugs.3.1.11 smooth test surface, nany rigid plastic, metal, orporcelain surface to which the suction cups can adhere, andthat is at least 2 in. (51 mm) larger in all directions than thelargest dimens

27、ions of the suction cup attachment device on theinfant bather.3.1.12 static load, nvertically downward load applied byweights or other means.4. Calibration and Standardization4.1 Unless otherwise noted, the infant bather shall becompletely assembled in accordance with the manufacturersinstructions.4

28、.2 The product to be tested shall be in a room with anambient temperature of 73 6 9F (23 6 5C) for at least 1 hprior to testing. Testing then shall be conducted within thistemperature range.4.3 All testing required by this specification shall be con-ducted on the same product sample.5. General Requi

29、rements5.1 Hazardous Sharp Edges or PointsThere shall be nohazardous sharp points or edges as defined in 16 CFR 1500.48and 16 CFR 1500.49 before or after the product has been testedto this consumer safety specification.5.2 Small PartsThere shall be no small parts as defined in16 CFR 1501 before test

30、ing or liberated as a result of testing tothis consumer safety specification.5.3 Lead in PaintsAll paint and surface coatings on theproduct shall comply with the requirements of 16 CFR 1303.5.4 Resistance to Collapse:5.4.1 When the product is placed in any manufacturersrecommended use position(s), l

31、atching and locking mecha-nisms designed to prevent the unintentional collapse of theproduct with the infant in it shall comply with either 5.4.1.1 or5.4.1.2.NOTE 1An attachment (such as a hook) where the weight of the childmaintains the engagement is not considered a latching and lockingmechanism.5

32、.4.1.1 Product shall be designed with a single actionmechanism that shall not release when tested in accordancewith 7.1.5.4.1.2 Product shall be designed with a double actionrelease system. There are no force requirements for a doubleaction release system.4Available from American National Standards

33、Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.F3343 1925.4.2 During and upon completion of the tests in accordancewith 7.4.1 and 7.4.2, the product shall remain in the manufac-turers recommended use position(s), and the latching andlocking mechanism(s) shall rema

34、in engaged and operative aftertesting.5.5 Scissoring, Shearing, and PinchingThe product, whenin the manufacturers recommended use position(s), shall bedesigned and constructed to prevent injury to the occupantfrom any scissoring, shearing, or pinching when members orcomponents rotate about a common

35、axis or fastening point,slide, pivot, fold, or otherwise move relative to one another.Scissoring, shearing, or pinching that may cause injury existswhen the edges of the rigid parts admit a probe greater than0.210 in. (5.33 mm) and less than 0.375 in. (9.53 mm) indiameter at any accessible point thr

36、oughout the range ofmotion of such parts.5.6 OpeningsHoles or slots that extend entirely through awall section of any rigid material less than 0.375 in. (9.53 mm)thick and admit a 0.210-in. (5.33 mm) diameter rod shall alsoadmit a 0.375 in. (9.53 mm) diameter rod. Holes or slots thatare between 0.21

37、0 in. (5.33 mm) and 0.375 in. (9.53 mm) andhave a wall thickness less than 0.375 in. (9.53 mm) but arelimited in depth to 0.375 in. (9.53 mm) maximum by anotherrigid surface shall be permissible (see Fig. 1 for examples). Theproduct shall be evaluated in all manufacturers recommendeduse positions.5.

38、7 Protective ComponentsIf the child can grasp protec-tive components between the thumb and forefinger, or teeth, orif there is at least a 0.04 in. (1.0 mm) gap between thecomponent and its adjacent parent component, such componentshall not be removed when tested in accordance with 7.2. Allprotective

39、 components that are accessible to a child in theproduct shall be evaluated.5.8 Labeling:5.8.1 Warning labels, whether paper or non-paper, shall bepermanent when tested in accordance with 7.3.1 7.3.4.5.8.2 Warning statements applied directly onto the surfaceof the product by hot stamping, heat trans

40、fer, printing, woodburning, etc. shall be permanent when tested in accordancewith 7.3.1 and 7.3.5.5.8.3 Non-paper labels shall not liberate small parts whentested in accordance with 7.3.6.5.9 If an infant bather can be converted to or has a mode thatcan be used on or in an infant bathtub, the produc

41、t in that modeshall comply with the requirements of Consumer SafetySpecification for Infant Bath Tubs F2670.5.10 Product must comply with the applicable requirementsof the Consumer Product Safety Improvement Act.5.11 ToysToy accessories attached to, removable from, orsold with an infant bather, as w

42、ell as their means of attachment,shall comply with the applicable requirements of ConsumerSafety Specification for Toy Safety F963.6. Performance Requirements6.1 Restraint SystemInfant bathers may have a permanentor removable passive crotch restraint as part of their design.They shall not have any a

43、dditional restraint system(s) whichrequires action on the part of the caregiver to secure or releasethe restraint.6.2 Structural IntegrityThere shall be no failure of seams,breakage of materials, or changes of adjustments that couldcause the product not to fully support the occupant or create ahazar

44、dous condition as defined in Section 5 when the productis tested in accordance with 7.4.1 for static load and 7.4.2 fordynamic load.6.3 Specific Requirements for Suction CupsInfant bathersthat utilize individual suction cups as a method of attachmentto a surface shall comply with the following requi

45、rements:6.3.1 Each suction cup shall remain attached to the productand shall not become damaged or broken after testing inaccordance with 7.5.1.6.3.2 The product shall remain attached to the test surfaceand shall not become damaged or broken after testing inaccordance with 7.5.2.6.4 Disassembly/Coll

46、apse While LiftingThe infant bathershall not disassemble or collapse when tested in accordancewith 7.6.6.5 StabilityThe product shall not tip over when tested inaccordance with 7.7.6.6 Fabric/Mesh IntegrityProducts with fabric/mesh shallmeet the requirements of 6.6.1 and 6.6.2. At the conclusion oft

47、esting required by 6.6.1 and 6.6.2, there shall be no failure ofseams, breakage of materials, or change in adjustment thatcould cause the product not to fully support the occupant or tocreate a hazardous condition as defined in Section 5.6.6.1 Seam StrengthAll seams supporting the weight ofthe occup

48、ant, when tested in accordance with Test MethodD1683/D1683M, shall have a breaking strength of 30 lbf (134N) or greater.6.6.2 Mesh/Fabric Attachment StrengthWhen tested inaccordance with 7.8, all locations on the product where a meshor fabric assembly is mechanically fastened to a rigid structuralFI

49、G. 1 Opening ExampleF3343 193element (for example, fastening of the assembly to a wireframe) shall not disengage or detach.7. Test Methods7.1 Single Action Release Mechanism:7.1.1 Set up the product in the manufacturers recom-mended use position(s).7.1.2 If the mechanism requires a pull or push action,gradually apply a force of 10 lbf (45 N) to the latching andlocking mechanism in the direction tending to release it. Applythe force within 5 s and maintain for an additional 10 s.7.1.3 If the mechanism requires a twist or turn action,gra