IEC 62132-8-2012 Integrated circuits - Measurement of electromagnetic immunity - Part 8 Measurement of radiated immunity - IC Stripline method《集成电路.电磁抗扰度的测量.第8部分 辐射抗扰度测量.集成电路(IC)电介质条状线法》.pdf

《IEC 62132-8-2012 Integrated circuits - Measurement of electromagnetic immunity - Part 8 Measurement of radiated immunity - IC Stripline method《集成电路.电磁抗扰度的测量.第8部分 辐射抗扰度测量.集成电路(IC)电介质条状线法》.pdf》由会员分享，可在线阅读，更多相关《IEC 62132-8-2012 Integrated circuits - Measurement of electromagnetic immunity - Part 8 Measurement of radiated immunity - IC Stripline method《集成电路.电磁抗扰度的测量.第8部分 辐射抗扰度测量.集成电路(IC)电介质条状线法》.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62132-8 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Integrated circuits Measurement of electromagnetic immunity Part 8: Measurement of radiated immunity IC stripline method Circuits intgrs Mesure de limmunit lectromagntique Partie 8: Mesure de limmunit rayonne Mthode de la l

2、igne TEM plaques pour circuit intgr IEC 62132-8:2012 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mec

3、hanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the a

4、ddress below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la ph

5、otocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national

6、 de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes

7、International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Usefu

8、l links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/j

9、ustpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 te

10、rms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, plea

11、se contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos de

12、s publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet

13、de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la C

14、EI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en

15、 franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous:

16、csciec.ch. IEC 62132-8 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Integrated circuits Measurement of electromagnetic immunity Part 8: Measurement of radiated immunity IC stripline method Circuits intgrs Mesure de limmunit lectromagntique Partie 8: Mesure de limmunit rayonne Mtho

17、de de la ligne TEM plaques pour circuit intgr INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 31.200 PRICE CODE CODE PRIX ISBN 978-2-83220-206-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechn

18、ique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 62132-8 IEC:2012 CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 6 3 T

19、erms and definitions . 6 4 General 7 5 Test conditions . 7 5.1 General . 7 5.2 Supply voltage. 8 5.3 Frequency range . 8 6 Test equipment . 8 6.1 General . 8 6.2 Cables . 8 6.3 Shielding . 8 6.4 RF disturbance generator 8 6.5 IC stripline . 8 6.6 50 termination 8 6.7 DUT monitor 8 7 Test setup 9 7.1

20、 General . 9 7.2 Test configuration 9 7.3 EMC test board (PCB) . 9 8 Test procedure . 9 8.1 General . 9 8.2 Operational check . 10 8.3 Immunity measurement . 10 8.3.1 General . 10 8.3.2 RF disturbance signal 10 8.3.3 Test frequency steps and ranges . 10 8.3.4 Test levels and dwell time . 10 8.3.5 DU

21、T monitoring . 10 8.3.6 Detail procedure 11 9 Test report 11 10 RF immunity acceptance level 11 Annex A (normative) Field strength determination 12 Annex B (normative) IC stripline descriptions . 15 Annex C (informative) Closed stripline geometrical limitations . 18 Bibliography 22 Figure 1 IC strip

22、line test setup . 9 Figure A.1 Definition of height (h) and width (w) of IC stripline . 12 Figure A.2 EM field distribution 13 Figure B.1 Cross section view of an example of an open IC stripline 15 Figure B.2 Cross section view of an example of a closed IC stripline . 16 62132-8 IEC:2012 3 Figure B.

23、3 Example of IC stripline with housing . 17 Figure C.1 Calculated H-field reduction of closed version referenced to referring open version as a function of portion of active conductor width of closed version to open version . 20 Figure C.2 Location of currents and mirrored currents at grounded plane

24、s used for calculation of fields . 21 Table 1 Frequency step size versus frequency range . 10 Table B.1 Maximum DUT dimensions for 6,7 mm IC stripline (Open version) . 16 Table B.2 Maximum DUT dimensions for 6,7 mm IC stripline (Closed version) . 16 Table C.1 Height of shielding, simulated at h bott

25、om= 6,7mm to achieve practically 50 system . 19 4 62132-8 IEC:2012 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INTEGRATED CIRCUITS MEASUREMENT OF ELECTROMAGNETIC IMMUNITY Part 8: Measurement of radiated immunity IC stripline method FOREWORD 1) The International Electrotechnical Commission (IEC) is a

26、 worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to ot

27、her activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the

28、 subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditio

29、ns determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC Nationa

30、l Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way i

31、n which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Pu

32、blication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC

33、is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its t

34、echnical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other

35、IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the su

36、bject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62132-8 has been prepared by subcommittee 47A: Integrated circuits, of IEC technical committee 47: Semiconductor devices. The text of this standard is based on the foll

37、owing documents: FDIS Report on voting 47A/882/FDIS 47A/886/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part of IEC 62

38、132 is to be read in conjunction with IEC 62132-1. 62132-8 IEC:2012 5 A list of all the parts in the IEC 62132 series, published under the general title Integrated circuits Measurement of electromagnetic immunity, can be found on the IEC website. Future standards in this series will carry the new ge

39、neral title as cited above. Titles of existing standards in this series will be updated at the time of the next edition. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the d

40、ata related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correc

41、t understanding of its contents. Users should therefore print this document using a colour printer. 6 62132-8 IEC:2012 INTEGRATED CIRCUITS MEASUREMENT OF ELECTROMAGNETIC IMMUNITY Part 8: Measurement of radiated immunity IC stripline method 1 Scope This part of IEC 62132 specifies a method for measur

42、ing the immunity of an integrated circuit (IC) to radio frequency (RF) radiated electromagnetic disturbances over the frequency range of 150 kHz to 3 GHz. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its ap

43、plication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050 (all parts), International Electrotechnical Vocabulary (available at http:/www.electropedia.org) IEC 62132-1:2006, Inte

44、grated circuits Measurement of electromagnetic immunity, 150 kHz to 1 GHz Part 1: General conditions and definitions IEC 61000-4-20, Electromagnetic compatibility (EMC) Part 4-20: Testing and measurement techniques Emission and immunity testing in transverse electromagnetic (TEM) waveguides 3 Terms

45、and definitions For the purpose of this document, the terms and definitions given in IEC 62132-1:2006, Clause 3, IEC 60050-131 and IEC 60050-161, and the following, apply. 3.1 transverse electromagnetic mode TEM waveguide mode in which the components of the electric and magnetic fields in the propag

46、ation direction are much less than the primary field components across any transverse cross-section Note 1 to entry: This note only applies to the French language. 3.2 TEM waveguide open or closed transmission line system, in which a wave is propagating in the transverse electromagnetic mode to prod

47、uce a specified field for testing purposes 3.3 IC stripline TEM waveguide, consisting of an active conductor placed on a defined spacing over an enlarged ground plane, connected to a port structure on each end and an optional shielded enclosure 62132-8 IEC:2012 7 Note 1 to entry: This arrangement gu

48、ides a wave propagation in the transverse electromagnetic mode to produce a specific field for testing purposes between the active conductor and the enlarged ground plane. The ground plane of the standard EMC test board according to IEC 62132-1:2006, Annex B, should be used. An optional shielding en

49、closure may be used for fixing the IC stripline configuration and for shielding purposes. This leads to a closed version of the IC stripline in opposite to the open version without shielding enclosure. For further information see Annex A. 3.4 two-port TEM waveguide TEM waveguide with input/output measurement ports at both ends 3.5 characteristic impedance mag