TIA-1084-B-1[E]-2014 Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for cdma2000 Spread Spectrum Systems (Incorporates Addendum 1).pdf

《TIA-1084-B-1[E]-2014 Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for cdma2000 Spread Spectrum Systems (Incorporates Addendum 1).pdf》由会员分享，可在线阅读，更多相关《TIA-1084-B-1[E]-2014 Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for cdma2000 Spread Spectrum Systems (Incorporates Addendum 1).pdf（90页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-1084-B-1E September 2014Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for cdma2000 Spread Spectrum Systems NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturer

2、s and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-

3、member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TI

4、A in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety

5、 problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. Any use of trademarks in this document

6、are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. TIA-PN-1084-B-1E, formulated under the cognizance of the TIA TR-45 Mobile (b) there is no assurance that the Document will be approved by any Commi

7、ttee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or

8、 issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the

9、Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opin

10、e or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more No

11、rmative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional ele

12、ments (as defined in the TIA Procedures for American National Standards) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclo

13、sure (see TIA Procedures for American National Standards Annex C.1.2.3) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Ess

14、ential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRA

15、NTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA E

16、XPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE

17、DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (IN

18、CLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMEN

19、TAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. 3GPP2 C.S0073-B v2.0 Revision History 1 2 Revision Description Date C.S0073-0 v1.0 Initial Release October 2005 C.S0073-A v1.0 Revision A April 2008 C.S0073-B v1.0 Revision B Aug

20、ust 2009 C.S0073-B v2.0 Bug fixes July 2014 3 3GPP2 C.S0073-B v2.0 i CONTENTS 1 1 Introduction 1-1 2 1.1 Scope . 1-3 3 1.2 Normative References . 1-3 4 2 Conformance Tests 2-1 5 2.1 MEID Support Indicator . 2-1 6 2.2 MEID, EXT_UIM_ID, MEID_ME, ESN_ME Information Records 2-3 7 2.3 Pseudo-ESN . 2-13 8

21、 2.4 Public LCM 2-18 9 2.5 LCM and Service Negotiation, Handoff for Mobile Station supporting Voice 10 Privacy 2-21 11 2.6 LCM and Service Negotiation, Handoff when Voice Privacy is not supported or is 12 disabled at the Mobile Station 2-26 13 2.7 Over-the-Air Service Provisioning (OTASP) Test 2-30

22、14 2.8 Reject Scenarios . 2-42 15 2.9 HRPD MEID and ESN HardwareID 2-44 16 3 Interoperability Tests . 3-1 17 3.1 MEID Support Indicator . 3-1 18 3.2 MEID, EXT_UIM_ID, MEID_ME, ESN_ME Information Records 3-3 19 3.3 Pseudo-ESN . 3-8 20 3.4 Public LCM 3-10 21 3.5 LCM and Service Negotiation, Handoff wh

23、en Voice Privacy is supported and 22 enabled 3-12 23 3.6 LCM and Service Negotiation, Handoff when Voice Privacy is not supported or is 24 disabled 3-15 25 3.7 Over-the-Air Service Provisioning (OTASP) Test 3-17 26 3.8 HRPD MEID HardwareID . 3-23 27 28 29 3GPP2 C.S0073-B v2.0 ii FIGURES 1 Figure 1 T

24、est Setup . 1-2 2 Figure 2 MEID handoff test setup .2-22 3 4 5 3GPP2 C.S0073-B v2.0 iii TABLES 1 Table 1 MEID_LEN and MEID fields in Status Response Message . 2-5 2 Table 2 EXT_UIM_ID fields in Extended Status Response Message 2-8 3 Table 3 MEID_ME Information Record in Extended Status Response Mess

25、age 2-11 4 Table 4 MEID and ESN fields in Extended Status Response Message . 2-16 5 Table 5 Public LCM Conformance Test Cases 2-19 6 Table 6 Change of LCM Conformance Test Cases with Voice Privacy Enabled 2-23 7 Table 7 Change of LCM Conformance Test Cases without Voice Privacy 2-27 8 Table 8 MEID C

26、apability Information Record in Protocol Capability Request Message . 2-32 9 Table 9 ICCID Capability Information Record in Protocol Capability Request Message 2-35 10 Table 10 Public LCM Interoperability Test Cases . 3-11 11 Table 11 Change of LCM Interoperability Test Cases . 3-13 12 13 14 3GPP2 C

27、.S0073-B v2.0 iv FOREWORD 1 (This foreword is not part of this Specificationdocument) 2 This Specification was prepared by Technical Specification Group C of the Third Generation 3 Partnership Project 2 (3GPP2). This Specification tests the signaling requirements of 4 C.S0072-0 (Mobile Station Equip

28、ment Identifier (MEID) Support for cdma20001 Spread 5 Spectrum Systems) in various configurations, including with an R-UIM or CSIM identified 6 by an Expanded UIMID (EUIMID). 7 8 SCOPE 9 (This scope is not part of this Specification) 10 This specification defines air interface signaling conformance

29、and interoperability tests for 11 CDMA base stations and mobile stations implementing MEID (See 5). 12 1 cdma2000 is the trademark for the technical nomenclature for certain specifications and standards of the Organizational Partners (OPs) of 3GPP2. Geographically (and as of the date of publication)

30、, cdma2000 is a registered trademark of the Telecommunications Industry Association (TIA-USA) in the United States.” 3GPP2 C.S0073-B v2.0 v The following standards contain provisions which, through reference in this text, 1 constitute provisions of this Specification. At the time of publication, the

31、 editions indicated 2 were valid. All standards are subject to revision, and parties to agreements based on this 3 Specification are encouraged to investigate the possibility of applying the most recent 4 editions of the standards indicated below. ANSI and TIA maintain registers of currently 5 valid

32、 national standards published by them. 6 3GPP2 Standards: 7 1. C.S0005-E v1.0, Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread 8 Spectrum Systems 9 2. C.S0066-0 v2.0, Over-the-Air Service Provisioning for MEID-Equipped Mobile Stations 10 in Spread Spectrum Systems 11 3. C.S0016-C v2.0,

33、Over-the-Air Service Provisioning of Mobile Stations in Spread 12 Spectrum Systems 13 4. C.S0044-A v1.0, Interoperability Specification for cdma2000 Air Interface 14 5. C.S0072-0 v1.0, Mobile Station Equipment Identifier (MEID) Support for cdma2000 15 Spread Spectrum Systems 16 6. C.S0023-C v2.0, Re

34、movable User Identity Module for Spread Spectrum Systems 17 7. C.S0065-0 v2.0, cdma2000 Application on UICC for Spread Spectrum Systems 18 8. C.S0024-0 v4.0, CDMA HighRate Packet Data Air Interface 19 9. C.S0024-A v3.0, CDMA HighRate Packet Data Air Interface 20 10. C.S0043-0 v1.0, Signaling Conform

35、ance Test Specification for cdma2000 Spread 21 Spectrum Systems 22 23 3GPP2 C.S0073-B v2.0 vi This page intentionally left blank. 1 3GPP2 C.S0073-B v2.0 1-1 1 Introduction 1 In this document, mobile station refers to a subscriber terminal, handset, PDA, wireless 2 local loop unit, or any other subsc

36、riber terminal that communicates with the base station 3 at the air interface. Base station refers to the composite functionality of the base station 4 and connected network elements or emulators. 5 This test specification covers test cases for P_REV_IN_USE 6 to 10. This test specification 6 also co

37、vers test cases for devices supporting 8 and/or 9. 7 The term “Card”, when capitalized, can refer to either an R-UIM card 6 or a CSIM card 7. 8 Separate signaling conformance tests are specified for mobile stations and base stations. 9 Conformance tests are typically performed using an emulator to i

38、nterface with the unit 10 under test, with a cabled connection for the RF interface. Any test should be executed only 11 if unit under test supports corresponding feature. 12 For interoperability test cases, a cabled connection is typically used for the air interface 13 connection between the mobile

39、 station and base station. 14 Test cases in this specification are applicable to non R-UIM mobile stations whether or not 15 they support a Card and R-UIMall mobile equipments equipment provisioned with an 16 MEID. Note that test cases for ESN provisioned mobile equipment with R-UIM carda Card 17 (p

40、rovisioned with UIMID, LF_EUIMID or SF_EUIMID) are not covered in this specification, 18 but test cases specified in 10 and 4 are sufficient to test R-UIMCard configurations with 19 ESN mobile stations. 20 The terms “true ESN” and “true UIMID” refer to any 32-bit number not starting with the 8-21 bi

41、t prefix 0x80. The terms “pseudo ESN”, pESN, pUIMID and “pseudo-UIMID” refer to any 22 32-bit number that does start with the 8-bit prefix 0x80. 23 Unless specified otherwise in a test case, channel conditions for a test shall be set to have 24 low FER. Unless specified otherwise in a test case, set

42、up shown in Figure 1 shall be used 25 for all test cases in this document. Note that mobile station shown in Figure 1 consists of 26 mobile equipment and User Identity Module (UIM). The UIM may be integrated or 27 removable. 28 29 30 3GPP2 C.S0073-B v2.0 1-2 T xR x ( A )R x ( B )B a s e S t a t i o

43、nM o b i l e S t a t i o nA n t e n n a1 Figure 1 Test Setup 2 3 3GPP2 C.S0073-B v2.0 1-3 1.1 Scope 1 This specification defines air interface signaling conformance and interoperability tests for 2 CDMA base stations and mobile stations implementing MEID (See 5). 3 1.2 Normative References 4 The fol

44、lowing standards contain provisions which, through reference in this text, constitute 5 provisions of this Specification. At the time of publication, the editions indicated were valid. 6 All standards are subject to revision, and parties to agreements based on this Specification 7 are encouraged to

45、investigate the possibility of applying the most recent editions of the 8 standards indicated below. ANSI and TIA maintain registers of currently valid national 9 standards published by them. 10 3GPP2 Standards:. 11 1. C.S0005-F v2.0, Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread 12 S

46、pectrum Systems, May 2014. 13 2. C.S0066-0 v2.0, Over-the-Air Service Provisioning for MEID-Equipped Mobile Stations in 14 Spread Spectrum Systems, July 2008. 15 3. C.S0016-D v2.0, Over-the-Air Service Provisioning of Mobile Stations in Spread 16 Spectrum Systems, April 2012. 17 4. C.S0044-D v1.0, I

47、nteroperability Specification for cdma2000 Air Interface, March 2014. 18 5. C.S0072-0 v1.0, Mobile Station Equipment Identifier (MEID) Support for cdma2000 19 Spread Spectrum Systems, August 2005. 20 6. C.S0023-D v3.0, Removable User Identity Module for Spread Spectrum Systems, 21 December 2013. 22

48、7. C.S0065-B v3.0, cdma2000 Application on UICC for Spread Spectrum Systems, 23 January 2014. 24 8. C.S0024-0 v4.0, CDMA HighRate Packet Data Air Interface, October 2002. 25 9. C.S0024-A v3.0, CDMA HighRate Packet Data Air Interface, September 2006. 26 10. C.S0043-B v1.0, Signaling Conformance Test

49、Specification for cdma2000 Spread 27 Spectrum Systems, March 2014 28 29 30 31 3GPP2 C.S0073-B v2.0 1-4 This page intentionally left blank.1 3GPP2 C.S0073-B v2.0 2-1 2 Conformance Tests 1 2.1 MEID Support Indicator 2 2.1.1 Mobile Station Test 3 2.1.1.1 Definition 4 This test verifies that the mobile station sets the MEID support indicator properly. This test 5 case is applicable to all mobile stations provisioned with MEID (e.g. mobile stations with or 6 without R-UIM, R-UIMa Card and mobile stations regardless of R-UIMCard configuration). 7 2.1.1.2 Traceabil