TIA TSB-38-1994 Test Procedure for Evaluation of 2-Wire 4-Kilohertz Voiceband Duplex Modems《评价2线4千赫双向调制解调器的测试程序》.pdf

《TIA TSB-38-1994 Test Procedure for Evaluation of 2-Wire 4-Kilohertz Voiceband Duplex Modems《评价2线4千赫双向调制解调器的测试程序》.pdf》由会员分享，可在线阅读，更多相关《TIA TSB-38-1994 Test Procedure for Evaluation of 2-Wire 4-Kilohertz Voiceband Duplex Modems《评价2线4千赫双向调制解调器的测试程序》.pdf（115页珍藏版）》请在麦多课文档分享上搜索。

1、TIA/EIA TELECOMMUNICATIONS SYSTEMS BULLETIN Test Procedure for Evaluation of 2- Wire 4-Kilohertz Voiceband Duplex Modems TSB-38 REAFFIRMED JULY 2002 DECEMBER 1994 TELECOMMUNICATIONS INDUSTRY ASSOCIATION The Teleconmiunications Industry Association represents the conmiunications sector of NOTICE TIA/

2、EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the

3、proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TIA/EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publicatio

4、ns preclude their voluntary use by those other than TIA/EIA members, whether the standard is to be used either domestically or internationally. Standards, Publications and Bulletins are adopted by EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action,

5、TIA/EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard, Publication, or Bulletin. Technical Bulletins are distinguished from TIA/EIA Standards or Interim Standards, in that they contain a compilation of engineering data

6、or information useful to the technical community, and represent approaches to good engineering practices that are suggested by the formulating committee. This Bulletin is not intended to preclude or discourage other approaches that similarly represent good engineering practice, or that may be accept

7、able to, or have been accepted by, appropriate bodies. Parties who wish to bring other approaches to the attention of the formulating committee to be considered for inclusion in future revisions of this Bulletin are encouraged to do so. It is the intention of the formulating committee to revise and

8、update this Bulletin from time to time as may be occasioned by changes in technology, industry practice, or government regulations, or for other appropriate reasons. (From Project No. 3-3175, formulated under the cognizance of the TIA TR-30.3 Subcommittee on Data Communications Network Interfaces) T

9、his document was reaffirmed by the Telecommunications Industry Association on June 1 O, 2002. Published by OTELECOMMUNICATIONS INDUSTRY ASSOCIATION 1994 Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to the current Catalog of ELECTRONIC INDUS

10、TRIES ALLIANCE STANDARDS and ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1 -800-854-71 79) International (303-397-7956) All rights reserved Printed in U.S.A. NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed has been prep

11、ared by one or more Engineering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees

12、 are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.orZr/standards/sfZr/engineering manual.ch. TIAS function is to administer the process, but not the content, of document

13、preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY INVOLVE THE USE OF INTELLECTUAL PROPERTY RIGHTS (“IPR), INCLUDING PENDING OR ISSUED PATENTS, OR COP

14、YRIGHTS, OWNED BY ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR. WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEMENT FROM THE HOLDER THEREOF IS REQUESTED, ALL IN ACCORDANCE WITH THE MANUAL. TIA TAKES NO POSITION W

15、ITH REFERENCE TO, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SCOPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS

16、FORA PARTICULAR PURPOSE PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION. OR USE, ITS MERCHANTABILITY

17、 AND ITS NON-INFRINGEMENT OF ANY THIRD TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOS

18、S OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE

19、OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. EIA TSB38 94 3234600 0567203 527 = rIA/EIA rELECOMMUNI CATIONS SYSTEMS BULLETIN rest Procedure for Evaluation of 2-Wire #-Kilohertz Voiceband Duplex Modems TSB38 DECEMBER 1994 TELECOMMUNICATIONS INDUST

20、RY ASSOCIATION EIA TSB38 94 = 3234600 O567202 463 H NOTICE TINEIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeabjity and improvement of products, and assisting the

21、 purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TIAIEIA from manufacturing or selling products not conforming to such Standards and Publicati

22、ons, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than TIA/?W members, whether the standard is to be used either domestically or internationally. Recommended Standards, Publications and Bulletins are adopted by WEiIA in accordance with the Am

23、erican National Standards Institute (ANSI) patent policy. By such action, TIA/EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Recommended Standard, Publication or Bulletin. Technical Bulletins are distinguished from TINEIA Rec

24、ommended Standards or Interh Standards, in that they contain a compilation of engineering data or information useful to the technical community, and represent approaches to good engineering practices that are suggested by the formulating committee. This Bulletin is not intended to preclude or discou

25、rage other approaches that similarly represent good engineering pdce, or that may be acceptable to, or have been accepted by, appropriate bodies. Parties who wish to bring other approaches to the attention of the formulating committee to be considered for inclusion in future revisions of this Bullet

26、in are encouraged to do so. It is the intention of the formulating committee to revise and update this Bulletin from time to time as may be occasioned by changes in technology, industry practice, or government regulations, or for other appropriate reasons. Published by -0MMUNICATIONS INDUSTRY ASSOCI

27、ATION 1994 Standards and Technology Department 2001 Pennsylvania Ave. N.W., Washington, D.C. 20006 PRICE Please refer to the current Catalog of EU, JEDEC and TIA STANDARDS and ENGI“G PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) AU ri

28、ghts reserved Printed in U.S.A. CONTENTS EIA TSB38 94 3234600 0567204 236 TSB-38 PAGE SCOPE . i NORMAllVE REFERENCES 2 DEFINmONS . 4 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.1 1 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 async

29、hronous . 4 bit . 4 bit-error ratio; BER . 4 block 4 block-error ratio; BLER 4 British Telecom Ziv-Lempel; BTLZ . 4 buffered mode; normal mode . 4 byte 4 character 4 compression mode . 5 compression ratio . 5 data terminal equipment; DTE . 5 dictionary size 5 direct mode 5 duplex modem; full duplex

30、modem . 5 error control mode 5 FOX message . 5 half duplex modem 6 impairment combination 6 line rate; data signalling rate . 6 maximum string length . 6 message-error ratio; MER 6 parity bit . 6 port rate 6 RTS/CTS flow control; hardware flow control . 6 signal converter 6 synchronous . 6 synchrono

31、us mode . 7 test channel . 7 test loop combination; TLC 7 throughput 7 two way transfer 7 XON/XOFF flow control; software flow control 7 one way transfer . 6 i TSB-38 EIA TSB3 94 3234b00 0567205 172 REQUI REM ENTS . u 8 4.1 Network simulator . 8 4.2 DTEs 8 NElWORK MODEL COVERAGE CONSIDERATIONS . TES

32、T PROCEDURES 13 6.1 6.2 6.3 6.4 6.5 6.6 Throughput vs . network model coverage 15 File-based with compression . 16 6.1.1 6 .I . 2 File-based without compression 18 22 Throughput vs . file type . Error ratio vs . network model coverage . 25 Bit- and block-error ratio vs . network model coverage 26 6.

33、3.1 6.3.2 Message-error ratio vs . network model coverage . 29 Connect reliability vs . test loop combinations 32 Character echo delay 35 Block acknowledge delay . 38 .ANNEX A (Normative) . 41 DTE Verification Procedures . 41 A ANNEX B (Normative) . 43 Description of Data Files 43 B ANNU( C (Informa

34、tive) . 44 Characteristics of Data Files . 44 ANNEX D (Informative) 47 Determination of Reference Throughput Values . 47 ANNEX E (Informative) . 49 C D E Error Rate Estimation . . 49 ? A EIA TSB38 74 3234b00 0567206 O09 TSB-38 ANNEX F (Informative) 55 F Data Reporting Format and Interpretation of Re

35、sults 55 Throughput vs . file type 62 Error ratio vs . network model coverage 64 Connect reliability vs . test loop combinations . 73 F.l F.2 F.3 F.4 F.5 F.6 Throughput vs . network model coverage . 55 Character echo delay . 78 Block acknowledge delay 82 ANNEX G (Infornative) . 86 G Call Initiation

36、Considerations 86 ANNEX H (Informative) . 88 H RTS/CTS Flow Control 88 ANNEX I (Informative) . 89 I Modem Overview 89 ANNEX J (Informative) . 98 J Minimizing test time . 98 ANNEX K (Informative) . 101 K Circuit Identification Cross-Reference . 101 iii . EIA TSB38 94 3234600 O567207 T45 E TSB-38 FORE

37、WORD (This Foreword is not part of this Bulletin) This document is intended to provide a common basis for comparison of mo- dem performance. Different test procedures described in this Bulletin empha- size different modem applications. The Throughput versus network model cov- erage test procedure, f

38、or example, is important for evaluating modem per- formance when used in asynchronous file transfer applications; the Error Rate versus Network Model Coverage test procedure is important for evaluating mo- dem performance in synchronous or asynchronous network applications. No single test is compreh

39、ensive enough to determine which modem will per- form best in all applications, but this series of tests permits the gathering of sufficient data on a modem to determine its strengths and weaknesses. Individual users shall decide which factors are important for their particular application or applic

40、ations. There are 11 annexes in this Bulletin. Annexes A and B are normative and are considered part of this Bulletin; annexes C through K are informative and are not considered part of this Bulletin. a EIA TSB38 94 W 3234600 0567208 981 TSB-38 INTRODUCTION Because of the lack of consistent test pro

41、cedures and criteria for interpretation of results, modem performance evaluations historically have resulted in widely varying modem comparisons. TIA TR-30.3 has created this Telecom- munications Systems Bulletin to resolve this problem. This Bulletin provides a consistent set of repeatable test pro

42、cedures designed to characterize the performance of modems. This is achieved by stating the precise configuration of all the required test equipment, then giving step-by- step instructions for performing each test. This document also suggests some formats for analyzing, interpreting, and presenting

43、the results. TSB-38 (This page left blank.) vi EIA TSB38 94 3234600 05672110 53T TSB-38 TEST PROCEDURE FOR EVALUATION OF 2-WIRE BER: ratio of erroneous bits to total bits received at a 3.4 block: group of contiguous bits. 3.5 received at a DTE-to-modem interface. block-error ratio; BLER: ratio of er

44、roneous blocks to total blocks 3.6 Recommendation V.42 bis. British Telecom Ziv-Lempel; BTLZ: compression algorithm used in NOTE - the order of the letters “Lz” and the name “Ziv-Lempel” is not a typographical error. 3.7 the ITU-T V.24 circuits 103 (transmit data) and 104 (receive data) transfer dat

45、a at a port rate independent of the line rate. The difference in transfer rates is compensated for by buffering data as required in the modem. Neither error correction protocols nor data compression algorithms are used. For modem modulation methods which transfer data synchronously, ITU-T V. 14 sync

46、hronous/asynchronous conversion is used within the modem. buffered mode; normal mode: mode of data transmission whereby 3.8 byte: group of 8 contiguous bits; octet. 3.9 character: for bit-serial interfaces, a group of five to eight contiguous data bits that is preceded by one start (condition 2, spa

47、ce) bit and followed by at least one complete stop (condition A, mark) bit; a parity bit appearing between the final data bit and the first (or only) stop bit is optional. For bit-parallel interfaces, a character is equivalent to a byte. 4 - EIA TSB38 94 3234600 0567234 385 H TSB-38 3.10 compression

48、 mode: mode of data transmission whereby the ITU-T circuits 103 (transmit data) and 104 (receive data) transfer characters of data at a DTE port rate independent of the modem-to-modem line rate, and the transferred information is then transformed inside the modem by a compression algorithm. Informat

49、ion is transferred reliably between modems using ITU-T V.42 error control, and is compressed by using ITU-T V.42 bis compression. 3.11 the compressed data. compression ratio: ratio of the size of the original data to the size of 3.12 and a data sink. A single computer may have two DTE port and, therefore, constitute two DTEs. data terminal equipment; DTE: equipment comprising a data source 3.13 maximum number of elements in the BTLZ coding dictionary. dictionary size: V.42 bis negotiated parameter Pl that specifies the 3.14 103 (transmit data) and 104 (receive data) t