SANS 105-F02-2009 Textiles - Tests for colour fastness Part F02 Specification for cotton and viscose adjacent fabrics《纺织品 色牢度试验 第F02部分：棉和粘胶贴衬织物规范》.pdf

《SANS 105-F02-2009 Textiles - Tests for colour fastness Part F02 Specification for cotton and viscose adjacent fabrics《纺织品 色牢度试验 第F02部分：棉和粘胶贴衬织物规范》.pdf》由会员分享，可在线阅读，更多相关《SANS 105-F02-2009 Textiles - Tests for colour fastness Part F02 Specification for cotton and viscose adjacent fabrics《纺织品 色牢度试验 第F02部分：棉和粘胶贴衬织物规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22998-6 SANS 105-F02:2009Edition 1ISO 105-F02:2009Edition 1SOUTH AFRICAN NATIONAL STANDARD Textiles Tests for colour fastness Part F02: Sp

4、ecification for cotton and viscose adjacent fabrics This national standard is the identical implementation of ISO 105-F02:2009 and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X 191

5、 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 105-F02:2009 Edition 1 ISO 105-F02:2009 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS SC 38A, Textile test methods Coloured textil

6、es the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED

7、DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member

8、body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedSANS 105-F02:2009This s tandard may only be used and printed by ap

9、proved subscription and freemailing clients of the SABS .ISO 105-F02:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is

10、normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part

11、in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to pre

12、pare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that

13、some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 105-F02 was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee SC 1, Tests for coloured textiles and colorants. This first ed

14、ition cancels and replaces Section F02 of the third edition of ISO 105-F (ISO 105-F:1985), which has been technically revised. ISO 105 was previously published in 13 “parts”, each designated by a letter (e.g. “Part A”), with publication dates between 1978 and 1985. Each part contained a series of “s

15、ections”, each designated by the respective part letter and by a two-digit serial number (e.g. “Section A01”). These sections are now being republished as separate documents, themselves designated “parts” but retaining their earlier alphanumeric designations. A complete list of these parts is given

16、in ISO 105-A01. SANS 105-F02:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SANS 105-F02:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 105-F02:200

17、9(E) ISO 2009 All rights reserved 1Textiles Tests for colour fastness Part F02: Specification for cotton and viscose adjacent fabrics 1 Scope This part of ISO 105 specifies an undyed cotton (and an undyed viscose) adjacent fabric which may be used for the assessment of staining in colour fastness te

18、sts. The staining properties of the cotton (and viscose) adjacent fabric under test are assessed against a cotton (and a viscose) reference adjacent fabric, using a cotton dyed reference fabric, all of which are available from a specified source. 2 Normative references The following referenced docum

19、ents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 105-A02, Textiles Tests for colour fastness Part A02: Grey scale for assess

20、ing change in colour ISO 105-A05, Textiles Tests for colour fastness Part A05: Instrumental assessment of change in colour for determination of grey scale rating ISO 105-C10:2006, Textiles Tests for colour fastness Part C10: Colour fastness to washing with soap or soap and soda ISO 105-J01, Textiles

21、 Tests for colour fastness Part J01: General principles for measurement of surface colour ISO 105-J02, Textiles Tests for colour fastness Part J02: Instrumental assessment of relative whiteness ISO 3071, Textiles Determination of pH of aqueous extract ISO 3801, Textiles Woven fabrics Determination o

22、f mass per unit length and mass per unit area 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 cotton adjacent fabric under test cotton adjacent fabric complying with the requirements in 4.1 3.2 cotton reference adjacent fabric cotton referenc

23、e adjacent fabric complying with the requirements in 4.1 SANS 105-F02:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 105-F02:2009(E) 2 ISO 2009 All rights reserved3.3 cotton dyed reference fabric cotton dyed reference fabric complyin

24、g with the requirements in 4.1 and dyed with C.I. Direct Blue 71 3.4 viscose adjacent fabric under test viscose adjacent fabric complying with the requirements in 4.2 3.5 viscose reference adjacent fabric viscose reference adjacent fabric complying with the requirements in 4.2 NOTE Cotton reference

25、adjacent fabric (3.2), cotton dyed reference fabric (3.3), and viscose reference adjacent fabric (3.5) are only available from lInstitut franais du textile et de lhabillement, Direction rgionale Est, 25, rue Alfred Werner, 68059 Mulhouse Cedex 2, France. 4 Specification for the adjacent fabrics 4.1

26、Specification for the cotton adjacent fabric The fabric shall have the following properties: 4.1.1 Mass per unit area: (115 5) g/m2determined in accordance with ISO 3801. 4.1.2 Whiteness value: Y10= 89 2 W10= 80 3 T10= 1 1 Measurements shall be made with the specular component included in accordance

27、 with ISO 105-J01, excluding 0/45 (45/0). Luminance (Y10), whiteness (W10) and tint (T10) values shall be calculated using CIE standard illuminant D65 and CIE 1964 supplementary standard colorimetric observer (10observer) in accordance with ISO 105-J02. Measure the whiteness degree of at least a fou

28、r-layer adjacent fabric to obtain a uniform whiteness measurement. 4.1.3 The pH of the aqueous extract: the pH shall be 7,0 0,5 when determined by the method specified in ISO 3071. NOTE Information about the production of the cotton reference adjacent fabric is included in a report by the co-secreta

29、riats of ISO/TC 38/SC 1. 4.2 Specification for the viscose adjacent fabric The fabric shall have the following properties: 4.2.1 Mass per unit area: (140 5) g/m2, determined in accordance with ISO 3801. 4.2.2 Whiteness value: Y10= 85 5 W10= 75 6 T10= 1,0 1,2 SANS 105-F02:2009This s tandard may only

30、be used and printed by approved subscription and freemailing clients of the SABS .ISO 105-F02:2009(E) ISO 2009 All rights reserved 3Measurements shall be made with the specular component included in accordance with ISO 105-J01, excluding 0/45 (45/0). Luminance (Y10), whiteness (W10) and tint (T10) v

31、alues shall be calculated using CIE standard illuminant D65 and CIE 1964 supplementary standard colorimetric observer (10 observer) in accordance with ISO 105-J02. Measure the whiteness degree of at least a four-layer adjacent fabric to obtain uniform whiteness measurement. 4.2.3 The pH of the aqueo

32、us extract: the pH shall be 7,0 0,5 when determined by the method specified in ISO 3071. NOTE Information about the production of the viscose reference adjacent fabric is included in a report by the co-secretariats of ISO/TC 38/SC 1. 5 Assessment of staining properties of cotton and viscose adjacent

33、 fabrics under test 5.1 General As adjacent fabrics are required to yield reproducible results when used in colour fastness tests, their most important property is standardized staining characteristics. The staining characteristics of the cotton adjacent fabric under test shall conform to those of t

34、he cotton reference adjacent fabric when tested using the cotton dyed reference fabric. The staining characteristics of the viscose adjacent fabric under test shall conform to those of the viscose reference adjacent fabric when tested using the cotton dyed reference fabric. 5.2 Test procedure 5.2.1

35、Test procedure for cotton adjacent fabric under test Place a cotton dyed reference fabric between the cotton adjacent fabric under test and the cotton reference adjacent fabric. To eliminate possible differences in test conditions, use both the cotton adjacent fabric under test and the cotton refere

36、nce adjacent fabric in the same composite specimen. Test the specimen in accordance with ISO 105-C10:2006, test number A (1). NOTE Information about the production of the cotton dyed reference fabric is included in a report by the co-secretariats of ISO/TC 38/SC 1. 5.2.2 Test procedure for viscose a

37、djacent fabric under test Place a cotton dyed reference fabric between the viscose adjacent fabric under test and the viscose reference adjacent fabric. To eliminate possible differences in test conditions, use both the viscose adjacent fabric under test and the viscose reference adjacent fabric in

38、the same composite specimen. Test the specimen in accordance with ISO 105-C10:2006, test number A (1). 5.3 Performance requirements The colour difference between the stain on the cotton adjacent fabric under test and the stain on the cotton reference adjacent fabric shall not be greater than 4-5 whe

39、n evaluated using the grey scale for assessing change in colour, in accordance with ISO 105-A02 or ISO 105-A05. The colour difference between the stain on the viscose adjacent fabric under test and the stain on the viscose reference adjacent fabric shall not be greater than 4-5 when evaluated using

40、the grey scale for assessing change in colour, in accordance with ISO 105-A02 or ISO 105-A05. SANS 105-F02:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 105-F02:2009(E) 4 ISO 2009 All rights reservedBibliography 1 ISO 105-A01, Texti

41、les Tests for colour fastness Part A01: General principles of testing 2 CIE Publication No. 15:2004, Colorimetry, 3rd ed. SANS 105-F02:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SABS Standards Division The objective of the SABS Stand

42、ards Division is to develop, promote and maintain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African National Standards

43、 should ensure that they possess the latest amendments or editions. The SABS continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the technical com

44、mittee responsible, the identity of which can be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South African National

45、 Standards. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessa

46、bs.co.za South African National Standards are also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both national and international standards, and is the official WTO/TBT en

47、quiry point for South Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosab

48、s.co.za Copyright The copyright in a South African National Standard or any other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means without p

49、rior written permission from the SABS Standards Division. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za