SAE AS 9805-1998 BOLT MACHINE-HEXAGON HEAD PD SHANK AMS 5643 190-32 UNJF-3A《AMS 5643 PD杆六角头机器螺栓 190-32 UNJF-3A》.pdf

《SAE AS 9805-1998 BOLT MACHINE-HEXAGON HEAD PD SHANK AMS 5643 190-32 UNJF-3A《AMS 5643 PD杆六角头机器螺栓 190-32 UNJF-3A》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 9805-1998 BOLT MACHINE-HEXAGON HEAD PD SHANK AMS 5643 190-32 UNJF-3A《AMS 5643 PD杆六角头机器螺栓 190-32 UNJF-3A》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、SAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole r

2、esponsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invites your written comments and suggestions.SHEET 1 OF 3AS9805THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS9805ISSUED 1998-11 REAFFIRMED 2007-06BOLT, MACHINE-HE

3、XAGON HEAD, PD SHANK,AMS 5643, .190-32 UNJF-3APREPARED BY COMMITTEE E-25 PROCUREMENT SPECIFICATION: NONEFEDERAL SUPPLY CLASS 5306NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS9805, NOTICE 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INT

4、O CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS9805, NOTICE 1. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDE

5、R THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTI

6、NG AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIE

7、D PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT.RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retri

8、eval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerS

9、ervicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BOLT, MACHINE-HEXAGON HEAD, PD SHANK,AMS 5643, .190-32 UNJF-3AAEROSPACE STANDARDAS9805SHEET 2 OF 3AS98

10、05Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BOLT, MACHINE-HEXAGON HEAD, PD SHANK,AMS 5643, .190-32 UNJF-3AAEROSPACE STANDARDAS9805SHEET 3 OF 3AS9805Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-