SAE AS 85421 3C-2008 FITTING TEE REDUCER BEAM SEAL 3000 4000 PSI 3 MALE ENDS《3外螺纹端3000 4000 psi异径光束密封三通配件》.pdf

《SAE AS 85421 3C-2008 FITTING TEE REDUCER BEAM SEAL 3000 4000 PSI 3 MALE ENDS《3外螺纹端3000 4000 psi异径光束密封三通配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85421 3C-2008 FITTING TEE REDUCER BEAM SEAL 3000 4000 PSI 3 MALE ENDS《3外螺纹端3000 4000 psi异径光束密封三通配件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, TEE, REDUCER, BEAM SEAL, 3000/4000 PSI, 3 MALE ENDS AS85421/3Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyin

2、g, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-01REVISED 2008-11 REAFFIRMED

3、 2015-04THIRD ANGLE PROJECTION CUSTODIAN: G-3 REV.C FEDERAL SUPPLY CLASS 4730AS85421/3 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS85421 /4/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisrepor

4、tis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE

5、invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85421/3C RATIONALE AS85421/3C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 EXCEPT JUMP SIZES STYLE 1 AE

6、ROSPACE STANDARD AS85421/3 SHEET 2 OF 3 REV. C FITTING, TEE, REDUCER, BEAM SEAL, 3000/4000 PSI, 3 MALE ENDS TABLE 1 - DIMENSIONAL DATA MASS LB/EA APPROX REF PORT (1) PORT (2) PORT (3) A B C D (REF) E RAD (MIN) TI CRES 04 04 04 .684 .684 .684 .500 .042 .047 .083 04 04 06 .684 .684 .704 .500 .042 .046

7、 .082 06 04 06 .704 .684 .704 .500 .042 .045 .080 06 06 04 .704 .704 .684 .500 .042 .045 .080 06 06 06 .704 .704 .704 .500 .042 .045 .080 06 06 08 .811 .811 .824 .562 .070 .074 .130 08 04 04 .824 .791 .791 .562 .070 .074 .131 08 04 08 .824 .791 .824 .562 .070 .074 .131 08 06 06 .824 .811 .811 .562 .

8、070 .073 .129 08 08 04 .824 .824 .791 .562 .070 .074 .131 08 08 06 .824 .824 .811 .562 .070 .073 .130 08 08 08 .824 .824 .824 .562 .070 .074 .132 10 08 08 .955 .891 .891 .688 .070 .108 .191 10 10 08 .955 .955 .891 .688 .070 .107 .189 10 10 10 .955 .955 .955 .688 .070 .107 .189 12 08 08 1.062 .958 .9

9、58 .875 .098 .165 .292 12 10 08 1.062 1.022 .958 .875 .098 .165 .291 12 12 08 1.062 1.062 .958 .875 .098 .160 .283 12 12 12 1.062 1.062 1.062 .875 .098 .158 .279 12 12 16 1.198 1.198 1.246 1.125 .098 .294 .520 16 10 16 1.246 1.158 1.246 1.125 .098 .280 .495 16 12 12 1.246 1.198 1.198 1.125 .098 .286

10、 .507 16 16 10 1.246 1.246 1.158 1.125 .098 .276 .488 16 16 16 1.246 1.246 1.246 1.125 .098 .266 .471 NOTES: /1/ MATERIAL: a. CODE LETTER P - TYPE 17-4PH CORROSION RESISTANT STEEL PER AMS 5643. b. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS 4928 OR AMS 4965. c. CODE LETTER V - TYPE 15-5PH

11、, CORROSION RESISTANT STEEL PER AMS 5659. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER P - CONDITION H1075 PER AMS 2759/3. b. MATERIAL CODE LETTER T - NONE. c. MATERIAL CODE LETTER V - AGE TO CONDITION H 1075 PER AMS-H-6875 OR AMS 2759/3. 3. FINISH: a. MATERIAL CODE LETTER P - PASSIVATE PER AMS 2700,

12、TYPE 6 OR 7 b. MATERIAL CODE LETTER T - NONE. c. MATERIAL CODE LETTER V - PASSIVATE PER AMS 2700, TYPE 6 OR 7. /4/ PROCUREMENT SPECIFICATION: AS85421 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORM

13、ANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS85421 FOR THIS STANDARD. SEE WW.EAUDITNET.COM FOR CURRENT QPL ON-LINE. AEROSPACE STANDARD AS85421/3 SHEET 3 OF 3 REV. C FITTING, TEE, REDUCER, BEAM SEAL, 3000/4000 PSI, 3 MALE ENDS /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS47

14、8 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER, AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING. b. FOR SIZES 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC

15、PART NUMBER AND MATERIAL CODE LETTER, AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING. 6. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 7. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. C

16、ORROSION RESISTANT STEEL AT 3000 psi. b. TITANIUM ALLOY AT 4000 psi. /8/ .030 MIN. RADIUS UNLESS QUALIFICATION OF SPECIAL PROCESS WITH SMALLER RADIUS, APPLICABLE FOR TITANIUM ALLOY PARTS ONLY. 9. DRY FILM LUBRICANT: APPLY DRY FILM LUBRICANT PER AS5272, TYPE I TO SEALING SURFACE. OVERSPRAY IN BORE IS

17、 NOT PERMITTED. 10. INTERPRETATION OF DRAWING PER ARP4296. 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 12. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 13. DIMENSI

18、ONING AND TOLERANCING: ASME Y14.5M-1994. 14. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS +.015, ANGULAR DIMENSIONS +030 15. EXAMPLE OF PART NUMBER: AS85421/3 V 06 04 06 SIZE CODE, TUBE SIZE OF PORT #3 IN .0625 INCREMENTS SIZE CODE, TUBE SIZE OF PORT #2 IN .0625 IN

19、CREMENTS SIZE CODE, TUBE SIZE OF PORT #1 IN .0625 INCREMENTS MATERIAL CODE LETTER /1/ BASIC PART NUMBER 16. IN THE EVENT OF CONFLICT BETWEEN THE TEXT OF THIS DOCUMENT AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS DOCUMENT TAKES PRECEDENCE. NOTHING IN THIS DOCUMENT, HOWEVER, SUPERSEDES APPLICABLE

20、 LAWS AND REGULATIONS UNLESS A SPECIFIC EXEMPTION HAS BEEN OBTAINED. 17. TITANIUM IS NOT RECOMMENDED FOR USE IN GASEOUS OR LIQUID OXYGEN SYSTEMS. 18. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.