SAE AS 85049 64A-2012 CONNECTOR ACCESSORIES ELECTRICAL STRAIN RELIEF SPLIT STRAIGHT CATEGORY 4C (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS)《(MIL-DTL-38999系列I和II连接器用)4C类、直的、分裂式应变.pdf

《SAE AS 85049 64A-2012 CONNECTOR ACCESSORIES ELECTRICAL STRAIN RELIEF SPLIT STRAIGHT CATEGORY 4C (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS)《(MIL-DTL-38999系列I和II连接器用)4C类、直的、分裂式应变.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85049 64A-2012 CONNECTOR ACCESSORIES ELECTRICAL STRAIN RELIEF SPLIT STRAIGHT CATEGORY 4C (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS)《(MIL-DTL-38999系列I和II连接器用)4C类、直的、分裂式应变.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CONNECTOR ACCESSORIES, ELECTRICAL, STRAIN RELIEF, SPLIT, STRAIGHT, CATEGORY 4C (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS) AS85049/64Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted

2、, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB A

3、DDRESS: http:/www.sae.org ISSUED2000-05REVISED 2012-01REAFFIRMED 2017-02THIRD ANGLE PROJECTION CUSTODIAN: AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS85049/64 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: AS85049 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance

4、thestateoftechnical andengineering sciences. The useofthis reportis entirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at wh

5、ichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written comments and suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS85049/64A RATIONALE AS85049/64A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIV

6、E-YEAR REVIEW POLICY. THE REQUIREMENTS FOR ACQUIRING THE ACCESSORIES DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS85049. FIGURE 1 DIMENSIONS AND CONFIGURATION TABLE 1 ACCESSORY DIMENSIONS ACCESSORY SHELL SIZE FITS CONNECTOR SHELL SIZE B +.000/-.062C MAX. DIA. D MAX.

7、 DIA E MAX. DIA F MIN SLOT G .032 SCREW LENGTH SCREW SIZE H WIRE BUNDLE ACCOMMODATIONSERIES II SERIES I MIN. MAX. 8 8 9 .562 (14.3) .75 (19.1) .85 (21.6) 1.10 (27.9) .125 (3.18) .625 (15.9) 6-32 .098 (2.49) .234 (5.94) 10 10 11 .688 (17.5) .85 (21.6) .90 (22.9) 1.10 (27.9) .125 (3.18) .625 (15.9) 6-

8、32 .153 (3.87) .234 (5.94) 12 12 13 .812 (20.6) 1.00 (25.4) 1.10 (27.9) 1.20 (30.4) .188 (4.78) .625 (15.9) 6-32 .190 (4.83) .328 (8.33) 14 14 15 .938 (23.8) 1.10 (27.9) 1.15 (29.2) 1.25 (31.8) .188 (4.78) .750 (19.1) 6-32 .260 (6.60) .457 (11.61) 16 16 17 1.062 (27.0) 1.25 (31.8) 1.30 (33.0) 1.35 (

9、34.2) .188 (4.78) .750 (19.1) 6-32 .283 (71.9) .614 (15.60) 18 18 19 1.188 (30.2) 1.40 (35.6) 1.50 (38.1) 1.60 (40.6) .250 (6.35) .750 (19.1) 8-32 .325 (8.26) .634 (16.10) 20 20 21 1.312 (33.3) 1.50 (38.1) 1.60 (40.5) 1.70 (43.1) .250 (6.35) .875 (22.2) 8-32 .343 (8.71) .698 (17.73) 22 22 23 1.438 (

10、36.5) 1.65 (41.9) 1.70 (43.2) 1.85 (47.0) .312 (7.92) 1.000 (25.4) 8-32 .381 (9.68) .823 (20.90) 24 24 25 1.562 (39.7) 1.75 (44.4) 1.80 (45.7) 1.95 (49.5) .312 (7.92) 1.125 (28.6) 8-32 .418 (10.62) .853 (21.66) AEROSPACE STANDARD AS85049/64 SHEET 2 OF 2 REV. A CONNECTOR ACCESSORIES, ELECTRICAL, STRA

11、IN RELIEF, SPLIT, STRAIGHT, CATEGORY 4C (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS85049. 1. DESIGN: CONNECTOR ACCESSORIES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INC

12、HES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR INFORMATION PURPOSES ONLY. THIS ACCESSORY WILL NOT ACCOMMODATE CONNECTORS USING SIZE 8, 4 AND 0 CONTACTS. INTERFACE DIMENSIONS SHALL CONFORM TO MIL-DTL-38999, SERIES I AND II. CLAMPS SHALL HAVE NO PROTRUSION OR SHARP EDGES WHICH MAY PINCH

13、 CABLE. IN THE ASSEMBLED MODE, THE COUPLING NUT SHALL BE CAPTIVATED TO THE ADAPTER BODY AND FREE TO ROTATE. FIGURE 1 DIMENSION “H” MAXIMUM IS APPLICABLE WHEN THE END OF THE SCREW IS FLUSH WITH “BB” OR A MAXIMUM OF TWO SCREW THREADS PROTRUDE. 2. MATERIAL: COUPLING NUT, RING, CLAMP, SADDLE BARS: ALUMI

14、NUM ALLOY IN ACCORDANCE WITH AS85049. FASTENERS: 300 SERIES CORROSION RESISTANT STEEL, PASSIVATED. 3. FINISH: IN ACCODANCE WITH AS845049. ALUMINUM COMPONENTS: 1/ N, 2/ W, X, Y, 2/ Z. 1/ N FINISH NOT FOR NAVY USE. RESTRICTED TO AIR FORCE SPACE APPLICATIONS ONLY. 2/ W AND Z FINISH NOT FOR USE IN SPACE

15、 APPLICATIONS. 4. PART NUMBER: SEE EXAMPLE BELOW: M85049/ 64 -10 W BASIC PART NUMBER SPECIFICATION SHEET ACCESSORY SHELL SIZE (SEE TABLE 1) FINISH 5. QUALIFICATION: SEE AS85049, CATEGORY 4C. ACCESSORY SHALL BE TESTED WITH MIL-DTL-38999 SERIES I CONNECTORS. NOTES: NOTICE THIS DOCUMENT REFERENCES A PA

16、RT WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. SPECIFICATION NOTES: A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.