SAE AS 81511 55A-2015 CONNECTOR RECEPTACLE CABLE CONNECTING ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING INDIVIDUAL RELEASE CRIMP TYPE CONTACTS (CLASS A .pdf

《SAE AS 81511 55A-2015 CONNECTOR RECEPTACLE CABLE CONNECTING ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING INDIVIDUAL RELEASE CRIMP TYPE CONTACTS (CLASS A .pdf》由会员分享，可在线阅读，更多相关《SAE AS 81511 55A-2015 CONNECTOR RECEPTACLE CABLE CONNECTING ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING INDIVIDUAL RELEASE CRIMP TYPE CONTACTS (CLASS A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, CABLE CONNECTING, ELECTRICAL,CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENTRESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4) AS81511/55Copyright 2015 SAE International All rights reserved. No part of this publication m

2、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U

3、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10REVISED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935AS81511/55 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provid

4、e that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eac

5、htechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/55A RATIONALE L

6、IMITED SCOPE REVISION IS REQUIRED TO CORRECT FIGURE 1, THE DIMENSION K LABEL AND NOTATION “OVER KNURL“ WERE OMITTED DURING THE AS CONVERSION. THE FIGURE 1 DRAWING NEEDS TO BE CORRECTED TO ADD THE K DIMENSION AND THE NOTATION. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREI

7、N SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR RECEPTACLE, CABLE CONNECTING (SERIES 4) AEROSPACE STANDARD AS81511/55 SHEET 2 OF 3 REV. A CONNECTOR, RECEPTACLE, CABLE CONNECTING, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIV

8、IDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4)TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .005 0.13 .015 0.38 .555 14.10 1.167 29.64 .010 0.25 .035 0.89 .575 14.61 1.187 30.15TABLE 2 - FIGURE 1 DIMENSIONS SHELL

9、SIZE B D F THREAD G ACROSS FLATS K AR BSC BR BSC CR BSC DR BSC EE BSC POSITION 1 2 3 4 5 68 .553 (14.05) .547 (13.89) .430 (10.92) .424 (10.77) 1/2-28UNEF-2A.565 (14.35) .553 (14.05) .780 (19.81) .760 (19.30)128 - - - 40 40 40 40 40 4010 .678 (17.22) .672 (17.07) .555 (14.10) .549 (13.94) 5/8-28UN-2

10、A .690 (17.53) .678 (17.22) .900 (22.86) .880 (22.35)105 140 215 265 60 46 46 60 89 6014 .928 (23.57) .922 (23.42) .805 (20.45) .799 (20.29) 7/8-28UN-2A .940 (23.88) .928 (23.57) 1.150 (29.21) 1.130 (28.70)105 140 215 265 60 46 46 60 89 6016 1.054 (26.77) 1.048 (26.62) .930 (23.63) .924 (23.47) 1-28

11、UN-2A 1.066 (27.08) 1.054 (26.77) 1.280 (32.51) 1.260 (32.00)105 140 215 265 50 50 50 50 50 5018 1.178 (29.92) 1.172 (29.77) 1.055 (26.80) 1.049 (26.64) 1 1/8-28UN-2A1.190 (30.23) 1.178 (29.92) 1.400 (35.56) 1.380 (35.05)105 140 215 265 50 50 50 50 50 50REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST O

12、F THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED,

13、 TOLERANCES ARE .016 INCHES. NORMAL MATING KEYWAY POSITION SHOWN IN FIGURE 1. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511, FIGURE 4. COLOR BANDS SHALL BE BLUE IN COLOR, .100 MAX. WIDTH AND SHALL BE VISIBLE WHEN MOUNTED. INSERT PROTRUSION FOR INSERTS CONTAINING SIZE 12 CONTACTS SHALL BE .070/.020. FO

14、R DIMENSIONS NOT SHOWN HEREIN, REFER TO AS81511 FIGURE 6. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. 3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF THE LETTER M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS ON THE CON

15、NECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/55FD01P1. M81511/55 F D 01 P 1 BASIC PART NUMBER CLASS SHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR KEY POSITIONS AEROSPACE STANDARD AS81511/55 SHEET 3 OF 3 REV. A CONNECTOR, RECEPTACLE, CABLE CONNECTING, ELECT

16、RICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4)4. SHELL POLARIZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS81969/16 INSERTION/REMOVAL TOOL. 6. MATING CONNECTOR: THIS RECEPTACLE MATES

17、 DIRECTLY WITH AS81511/6 AND /56 PLUGS. APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN. 2. FOR SHELL SIZES 20, 22, AND 24, USE AS81511/25 OR /45. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CON

18、SULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.