SAE AS 6298-2015 CLAMP ASSEMBLY LOOP CUSHIONED HINGED.pdf

《SAE AS 6298-2015 CLAMP ASSEMBLY LOOP CUSHIONED HINGED.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6298-2015 CLAMP ASSEMBLY LOOP CUSHIONED HINGED.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDCLAMP ASSEMBLY, LOOP, CUSHIONED HINGEDAS6298Copyright 2015 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, w

2、ithout the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2015-12THIRD ANGLE PROJECTIONCUSTODIAN: G-3/G-3EFEDERAL SUPPLY CLA

3、SS5340AS6298SHEET 1 OF 3PROCUREMENT SPECIFICATION: NONE /4/SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany

4、patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report

5、, please visit http:/www.sae.org/technical/standards/AS6298RATIONALENEW PART STANDARD.E/6/G/6/ /7/TD/6/1515( A)2X0 MINA BBCCXLOCATION OFIDENTIFICATION /11/DIRECTION OF GRAIN.228.208.25 MIN.35 MAX.25 MAX.515.485.258.242R.39.37/9/FIGURE 1 - CLAMP ASSEMBLY, LOOPHR JR F2X NSECTION C - CENLARGEDSECTION B

6、 - BENLARGEDCUSHION BOXCLAMP BAND REMOVEDVIEW AENLARGEDBANDCUSHION(.052).540.5102X.062.0422X.062.042.072.052SURFACE AAEROSPACE STANDARDAS6298SHEET 2 OF 3CLAMP ASSEMBLY, LOOP, CUSHIONED HINGEDTABLE 1A - DIMENSIONSBASIC NO.AS6298/18/SIZE CODE (A)D.015E.015F.016G+.015H.005J.015 NT.00504 .350 .250 .529

7、.062 .062 .065 .062 .037-.065 .03205 .413 .312 .560 .062 .062 .065 .062 .037-.065 .03206 .475 .375 .592 .062 .062 .065 .062 .037-.065 .03207 .538 .438 .623 .062 .062 .065 .062 .037-.065 .03208 .600 .500 .654 .062 .062 .065 .062 .037-.065 .03209 .663 .562 .749 .094 .062 .100 .109 .055-.100 .05010 .72

8、5 .625 .780 .094 .062 .100 .109 .055-.100 .05011 .788 .688 .811 .094 .062 .100 .109 .055-.100 .05012 .850 .750 .842 .094 .062 .100 .109 .055-.100 .05013 .913 .812 .858 .094 .062 .100 .109 .055-.100 .05014 .975 .875 .889 .094 .062 .100 .109 .055-.100 .05015 1.038 .938 .920 .094 .062 .100 .109 .055-.1

9、00 .05016 1.100 1.000 .951 .094 .062 .100 .109 .055-.100 .05017 1.162 1.062 .983 .094 .062 .100 .109 .055-.100 .050NOTES:/1/ MATERIAL:BAND:a. CODE LETTER A - TYPE A286 CORROSION RESISTANT STEEL PER AMS5525.b. CODE LETTER C - TYPE 321 CORROSION RESISTANT STEEL PER AMS5510.c. CODE LETTER P - 17-7PH CO

10、RROSION RESISTANT STEEL PER AMS5528.CUSHION:a. CODE LETTER P - POLYBENZIMIDAZOLE (PBI) POLYMIDE FIBERGLASS PER AMS3677.2. HEAT TREATMENT:a. BAND MATERIAL CODE LETTER A - PRECIPITATION HEAT TREAT TO CONDITION STA PER AMS2759/3.b. BAND MATERIAL CODE LETTER C - NONE.c. BAND MATERIAL CODE LETTER P - STR

11、ESS RELIEVE AND HEAT TREAT TO CONDITION TH1100 PER AMS2759/3 AFTER FORMING.3. FINISH:a. BAND MATERIAL CODE LETTER A - PASSIVATE PER AMS2700, TYPE 2 OR 8.b. BAND MATERIAL CODE LETTER C - PASSIVATE PER AMS2700, TYPE 6 OR 7.c. BAND MATERIAL CODE LETTER P - PASSIVATE PER AMS2700, TYPE 2 OR 8./4/ PROCURE

12、MENT SPECIFICATION: NONE. THE DRAWING AND ALL THE SPECIFIED DOCUMENTS DEFINE THE REQUIREMENTS FOR THE END PRODUCT. ALL THE REQUIREMENTS MUST BE MET IN ORDER TO IDENTIFY THE ITEM WITH THAT PART NUMBER.USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR

13、MEANS.5. CLAMPS SHALL COMPLETE 10,000,000 CYCLES WITHOUT FAILURE WHEN SUBJECTED TO VIBRATION FATIGUE TEST IN ACCORDANCE WITH AS1974. TEST SAMPLES FOR QUALIFICATION TESTS SHALL CONSIST OF ONE CLAMP OF SIZE -08, -12, AND -16 FOR EACH BAND MATERIAL.AEROSPACE STANDARDAS6298SHEET 3 OF 3CLAMP ASSEMBLY, LO

14、OP, CUSHIONED HINGED/6/ DIMENSIONS D, G, AND E SHALL BE WITHIN TOLERANCE LIMITS SPECIFIED WHEN ASSEMBLED ON A BAR WITH A DIAMETER EQUAL TO NOMINAL D r.001. DIMENSION G APPLIES WITH CLAMP CLOSED./7/ IN THE ASSEMBLED CONDITION, TOP LEG MUST NEST INTO BOTTOM LEG JOGGLE AND CUSHION ENDS SHALL MEET TO FO

15、RM A COMPLETE CLOSURE. THE ENDS OF CUSHION SHALL MEET WHEN THE CLAMP IS IN THE INSTALLED POSITION.8. DIMENSIONS SHOWN FOR CUSHION APPLY IN THE UNASSEMBLED CONDITION./9/ MOUNTING HOLE SIZE SHALL BE AS SPECIFIED BY THE PART NUMBER SUFFIX LETTER. /18/10. THE CUSHION SHALL BE FREE FROM SPLITS OR TEARS I

16、N THE FABRIC, AND SHALL BE FREE FROM TORN OR FRAYED ENDS AT THE CUSHION CUT-OFF./11/ IDENTIFICATION: MARK PER AS478 CLASS C OR D, OR METHOD 2A1 PART NUMBER AND MANUFACTURERS NAME, CAGE CODE OR TRADEMARK. DO NOT MARK IN RADIUS.12. INTENDED USE: THESE CLAMPS ARE INTENDED FOR USE AS TUBE AND WIRE BUNDL

17、E SUPPORTS AT TEMPERATURES UP TO 554 F (290 C).13. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT O

18、F THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.14. METAL BANDS SHALL HAVE ALL BURRS AND SHARP EDGES REMOVED.15. CUSHION MATERIAL TO BE F

19、LUSH WITH SURFACE A +.125, .032.16. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.17. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 030./18/ EXAMPLE OF PART NUMBER:BASIC PART NUMBERBAND MATERIAL CODE LETTER /1/SIZE CODE, TUBE SIZE IN .062 INCREMENTSCUSHION MATERIAL CODE LETTER /1/MOUNTING HOLE SIZE /9/A = .218-.228B = .274-.288AS6298 C 08 P A