SAE AS 6095-2011 FITTING 37 PHERICAL FLARED CONNECTOR MULTIPLE FLUID PRESSURE LINE TEE《三通管多流体压力线连接器37球面扩口接头》.pdf

《SAE AS 6095-2011 FITTING 37 PHERICAL FLARED CONNECTOR MULTIPLE FLUID PRESSURE LINE TEE《三通管多流体压力线连接器37球面扩口接头》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6095-2011 FITTING 37 PHERICAL FLARED CONNECTOR MULTIPLE FLUID PRESSURE LINE TEE《三通管多流体压力线连接器37球面扩口接头》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD FITTING, 37 SPHERICAL FLARED, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, TEE AS6095Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p

2、hotocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2011-05THIRD ANGLE PROJ

3、ECTION CUSTODIAN: SAE G-3/G-3B FEDERAL SUPPLY CLASS 4730 AS6095SHEET 1 OF 3PROCUREMENT SPECIFICATION: /4/ AS6076SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits

4、applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestion

5、s. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6095RATIONALE THIS SAE AEROSPACE STANDARD (AS) ESTABLISHES THE REQUIREMENTS FOR THE TEE FITTING WITH 37 DEGREE SPHERICAL FLARED TUBE. FIGURE 1 - FITTING, CONNECTOR, TEE AEROSPA

6、CE STANDARD AS6095SHEET 2 OF 3FITTING, 37 SPHERICAL FLARED, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, TEE TABLE 1A - DIMENSIONS BASIC NO. AS6095/13/SIZE CODE (NOMINAL TUBE SIZE)T THREAD PERAS8879CLASS 3A A.023 C.005 D.005 E F.001 04 .250 .4375-20 UNJF 1.148 .692 .474 .562 .439 05 .312 .5000-20 UNJF 1

7、.148 .755 .536 .625 .501 06 .375 .5625-18 UNJF 1.273 .817 .599 .750 .564 08 .500 .7500-16 UNJF 1.460 1.005 .786 .937 .751 10 .625 .8750-14 UNJF 1.680 1.130 .911 1.125 .876 12 .750 1.0625-12 UNJ 2.023 1.318 1.099 1.375 1.063 16 1.000 1.3125-12 UNJ 2.398 1.568 1.349 1.687 1.313 TABLE 1B - DIMENSIONS A

8、ND WEIGHTS BASIC NO. AS6095/13/SIZE CODE G H.010 K V LB/EAAPPROX. REF ALLB/EAAPPROX. REF STEELLB/EAAPPROX. REF TI04 .437 .750 .375 .797-.815 .0334 .0958 .0528 05 .437 .750 .500 .797-.815 .0301 .0863 .0476 06 .500 .875 .500 .985-1.003 .0492 .141 .0779 08 .500 1.125 .750 1.173-1.191 .0822 .236 .130 10

9、 .625 1.375 .812 1.355-1.380 .130 .374 .206 12 .625 1.625 1.000 1.668-1.693 .224 .642 .354 16 .812 2.125 1.500 2.042-2.072 .366 1.05 .580 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ M

10、ATERIAL: a. CODE LETTER F - TYPE 4130 ALLOY STEEL FORGING OR BAR PER AMS-S-6758 OR AMS6370; OR TYPE 4140 PER AMS6382. /2/ b. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5639. c. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5648. d. C

11、ODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5645. e. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928. f. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY PER AMS4141; OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9; OR TYPE 7075-T7351 ALUMINUM ALLOY BAR

12、 PER AMS4124. /2/ /2/ HEAT TREATMENT: a. MATERIAL CODE LETTER F - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTER W SEE ELECTRICAL CONDUCTIVITY AND HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. c. OTHER MATERIAL CODE LETTERS - NONE. AEROSPACE STANDARD AS6095SHEE

13、T 3 OF 3FITTING, 37 SPHERICAL FLARED, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, TEE 3. FINISH: a. MATERIAL CODE LETTER F - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTERS J, K, AND R - PASSIVATE PER

14、AMS2700, TYPE 6 OR 7. c. MATERIAL CODE LETTER T - ANODIZE PER AMS2488 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 WITH COLOR PER PROCUREMENT SPECIFICATION. d. MATERIAL CODE LETTER W: 1. ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2

15、. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTERTHE SIZE CODE IN THE PART NUMBER. HIGH PURITY ALUMINUM COAT PER PROCUREMENT SPECIFICATION. /4/ PROCUREMENT SPECIFICATION: AS6076 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFI

16、CATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURER LIST (QML) FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT ./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR M

17、ETHOD 7A3, 15A3, OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” AND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN

18、SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. SIZES 04 THROUGH 12 IN ALUMINUM ALLOY AND SIZES 04 THROUGH 16 IN STEEL AND TITANIUM ALLOY AT 3000 psi. b. SIZE16 IN ALUMINUM ALLOY AT 1500 psi. 7. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TA

19、BLE 8. 8. INTERPRETATION OF DRAWING PER ARP4296. 9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra. 10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 11. DIMENSIONING

20、 AND TOLERANCING: ASME Y14.5M-1994. 12. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 DEGREES 30. /13/ EXAMPLE OF PART NUMBER: AS6095 W 08 VBASIC PART NUMBER SIZE CODE, TUBE SIZE IN .062 INCREMENTSMATERIAL CODE LETTER /1/ THE FINISH CODE LETTER “V” WILL BE PLACED HERE ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUM