SAE AS 39029 72A-2010 CONTACTS ELECTRICAL CONNECTOR SOCKET REMOVABLE SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I II III AND IV MIL-DTL-24308 AND MIL-DTL-55302 68 7.pdf

《SAE AS 39029 72A-2010 CONTACTS ELECTRICAL CONNECTOR SOCKET REMOVABLE SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I II III AND IV MIL-DTL-24308 AND MIL-DTL-55302 68 7.pdf》由会员分享，可在线阅读，更多相关《SAE AS 39029 72A-2010 CONTACTS ELECTRICAL CONNECTOR SOCKET REMOVABLE SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I II III AND IV MIL-DTL-24308 AND MIL-DTL-55302 68 7.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CONTACTS, ELECTRICAL CONNECTOR, SOCKET, REMOVABLE, SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I, II, III, AND IV,MIL-DTL-24308, AND MIL-DTL-55302/68, /71, AND /75 CONNECTORS) AS39029/72Copyright 2016 SAE International All rights reserved. No part of this publicatio

2、n may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outsid

3、e USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2000-07 REVISED 2010-11 REAFFIRMED2016-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS39029/72 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: AS39029 SAE Technical Stand

4、ardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SA

5、E reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled. SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS39029/72A RATIONALE

6、AS39029/72A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS39029. FIGURE 1 - CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS39029/72 SHEE

7、T 2 OF 4 REV. A CONTACTS, ELECTRICAL CONNECTOR, SOCKET, REMOVABLE, SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I, II, III, AND IV,MIL-DTL-24308, AND MIL-DTL-55302/68, /71, AND /75 CONNECTORS) BIN CODE A B C D E MIN 393 .205 (5.21) .200 (5.08) .344 (8.74) .338 (8.59) .538 (13.67) REF .2

8、89 (7.34) .279 (7.09) .248 (6.30) 394 .306 (7.77) .302 (7.67) .237 (6.02) .231 (5.87) .538 (13.67) REF 395 .355 (9.02) .340 (8.64) .340 (8.64) REF .685 (17.40) .675 (17.15) 524 .264 (6.71) .249 (6.32) .278 (7.06) REF .532 (13.51) .522 (13.26) .626 (15.90) .616 (15.65) .585 (14.86) 525 .247 (6.27) .2

9、32 (5.89) .494 (12.55) REF .731 (18.57) .721 (18.31) 526 .355 (9.02) .340 (8.64) .340 (8.64) REF .685 (17.40) .675 (17.15) FIGURE 1 - CONFIGURATION AND DIMENSIONS - CONTINUED TABLE I - DESIGN CHARACTERISTICS BIN CODE COLOR BANDS MATING END SIZETYPE CLASS 1ST2ND3RD393 ORANGE WHITE ORANGE 22 A A 394 O

10、RANGE WHITE YELLOW 22 395 ORANGE WHITE GREEN 22 524 GREEN RED YELLOW 22 525 GREEN RED GREEN 22 526 GREEN RED BLUE 22 AEROSPACE STANDARD AS39029/72 SHEET 3 OF 4 REV. A CONTACTS, ELECTRICAL CONNECTOR, SOCKET, REMOVABLE, SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I, II, III, AND IV,MIL-D

11、TL-24308, AND MIL-DTL-55302/68, /71, AND /75 CONNECTORS) TABLE 2 - TOOLS BIN CODE INSTALLING TOOL REMOVAL TOOL 393, 394, 395, 524, 525, 526 M81969/1-04 (GREEN) M81969/8-01 M81969/1-04 (WHITE) M81969/8-02 TABLE 3. PART NUMBERS BIN CODE PART NUMBER SUPERSEDED PART NUMBER 393 M39029/72-393 M39029/72-1

12、394 M39029/72-394 M39029/72-2395 M39029/72-395 M39029/72-3 524 M39029/72-524 -525 M39029/72-525 - 526 M39029/72-526 -REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS39029. 1. DESIGN: CONTACTS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIME

13、NSIONS ARE IN INCHES. DIMENSIONS SHOWN APPLY AFTER PLATING. THE RIGHT SIDE OF THE “E” DIMENSION IS THE POINT AT WHICH A SQUARE ENDED PIN OF THE SAME BASIC DIAMETER AS THE MATING CONTACT FIRST ENGAGES THE SOCKET CONTACT SPRING. 2. TOOLS: TOOLS REQUIRED FOR THE INSTALLING/REMOVAL FROM THE CONNECTOR SH

14、ALL BE IN ACCORDANCE WITH TABLE 2. 3. PART NUMBERS: CONTACT PART NUMBERS SHALL BE IN ACCORDANCE WITH TABLE 3. SUPERSEDED PART NUMBERS ARE AS SPECIFIED. 4. MATERIALS: MATERIALS SHALL BE IN ACCORDANCE WITH AS39029. 5. MECHANICAL: WIRE WRAPPING: WIRE WRAPPING SHALL BE CLASS A AND WRAPPED IN ACCORDANCE

15、WITH MIL-STD-1130. CAUTION: MAINTAIN LIGHT TENSION ON THE WIRE AT THE START OF THE WRAP UNTIL ONE COMPLETE TURN HAS BEEN MADE. EDGE BURRS: WRAPPOST EDGE BURRS SHALL BE .0015 INCH (0.14 MM), MAXIMUM. 6. ELECTRICAL: ELECTRICAL REQUIREMENTS SHALL BE IN ACCORDANCE WITH AS39029. 7. ENVIRONMENTAL: ENVIRON

16、MENTAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. AEROSPACE STANDARD AS39029/72 SHEET 4 OF 4 REV. A CONTACTS, ELECTRICAL CONNECTOR, SOCKET, REMOVABLE, SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I, II, III, AND IV,MIL-DTL-24308, AND MIL-DTL-55302/68, /71, AND /75 CONNECTORS) 8. QU

17、ALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS39029 AND MIL-STD-1130 FOR CLASS A WRAP. SUPPLIERS QUALIFIED TO AS39029/58 (M39029/58-362) NEED ONLY TEST IN ACCORDANCE WITH MIL-STD-1130 TO QUALIFY THIS CONTACT. THE MANUFACTURERS RELIABILITY ASSURANCE PROGRAM SHALL COMPLY WITH THE AS9100 AER

18、OSPACE STANDARD FOR QUALITY MANAGEMENT SYSTEM REQUIREMENTS. OTHER ESTABLISHED AND INDUSTRY RECOGNIZED QUALITY ASSURANCE STANDARDS THAT ASSURE ALL PRODUCTS PRODUCED CONFORM TO THE CONTRACT REQUIREMENTS ARE ACCEPTABLE. HOWEVER, IF USED, IT IS THE RESPONSIBILITY OF THE MANUFACTURER TO PROVIDE EVIDENCE

19、OF COMPLIANCE TO AS9100. THE QUALIFYING ACTIVITY (QA) AUTHORITY RESERVES THE RIGHT TO MONITOR, MEASURE, AND VALIDATE COMPLIANCE AT THEIR DISCRETION. APPLICATION NOTES: 1. CONTACT MATES DIRECTLY WITH AN AS39029/58 PIN CONTACT AS SHOWN IN TABLE 4. TABLE 4. CONTACT MATING PART NUMBERS AS39029/72 BIN CO

20、DE MATING AS39029 SLASH SHEET/BIN CODE -393, -394, -395, -524, -525, -526 M39029/58-360, -361 1/, -362 1/ 1/ INACTIVE FOR NEW DESIGN 2. USAGE DATA (SEE TABLE 5): THESE CONTACTS ARE FOR USE ONLY ON INTERNAL WIRING OF EQUIPMENT AND EQUIPMENT PANELS. FOR MIL-DTL-38999, USE IS RESTRICTED TO RECEPTACLES.

21、 WHEN USED IN RECOMMENDED CONNECTORS, THESE CONTACTS ASSURE THE USER OF AN ADEQUATE LENGTH FOR PROPER WRAPPING. TABLE 5. USAGE DATA CONNECTOR TYPE M39029/72 CONTACT USED MIL-DTL-38999 SERIES II MS27499E MS27508E MS27513 -393, -394, -395 MIL-DTL-38999 SERIES I AND III MS27495 MS27505 -524, -525, -526

22、 M38999/42 SERIES IV -524, -525, -526 MIL-DTL-24308/2 MIL-DTL-24308/6 MIL-DTL-55302/68 MIL-DTL-55302/71 MIL-DTL-55302/75 -393, -394, -395 3. THIS CONTACT IS NOT FOR USE IN AS50881 APPLICATIONS. SPECIFICATION NOTES: A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOC

23、ATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.