SAE AS 39029 71A-2010 Contacts electrical connector pin removable solderless wrappost termination (for MIL-DTL-38999 series I II III and IV MIL-DTL-24308 MIL-DTL-83733 and MIL-DTL-.pdf

《SAE AS 39029 71A-2010 Contacts electrical connector pin removable solderless wrappost termination (for MIL-DTL-38999 series I II III and IV MIL-DTL-24308 MIL-DTL-83733 and MIL-DTL-.pdf》由会员分享，可在线阅读，更多相关《SAE AS 39029 71A-2010 Contacts electrical connector pin removable solderless wrappost termination (for MIL-DTL-38999 series I II III and IV MIL-DTL-24308 MIL-DTL-83733 and MIL-DTL-.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) CONTACTS, ELECTRICAL CONNECTOR, PIN, REMOVABLE, SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I, II, III AND IV,MIL-DTL-24308, MIL-DTL-83733, AND MIL-DTL-55302/69 CONNECTORS) AS39029/71Copyright 2010 SAE International All rights reserved. No part of this publicatio

2、n may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outsid

3、e USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-07REVISED 2010-11THIRD ANGLE PROJECTION CUSTODIAN: AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS39029/71SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: AS39029SAE Technical Standards Board Rules provide tha

4、t: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachte

5、chnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS39029/71ARATIONALE REVISED TO INCLU

6、DE COMMENTS RECEIVED BY THE GOVERNMENT AND INDUSTRY, REMOVE GOVERNMENT JARGON AND MIL-STD-790 REQUIREMENTS, UPDATE REFERENCES, ALIGN SPECIFICATION WITH SAE GUIDELINES, AND REVIEW SPECIFICATION FOR KNOWN TECHNICAL PROBLEMS. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONS

7、IST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS39029. BIN CODE A B C 390.205 (5.21) .200 (5.08) .344 (8.74) .338 (8.59) .538 (13.67) REF 391.306 (7.77) .302 (7.67) .237 (6.02) .231 (5.87) .538 (13.67) REF 392.355 (9.02) .340 (8.64) .340 (8.64) REF .685 (17.40) .675 (17.15) FIGURE 1 -

8、CONFIGURATION AND DIMENSIONS Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/71SHEET 2 OF 3REV. A(R) CONTACTS, ELECTRICAL CONNECTOR, PIN, REMOVABLE, SOLDERLESS WRAPPOST TER

9、MINATION (FOR MIL-DTL-38999 SERIES I, II, III AND IV, MIL-DTL-24308, MIL-DTL-83733, AND MIL-DTL-55302/69 CONNECTORS) TABLE 1 - DESIGN CHARACTERISTICS BINCODE COLOR BANDS MATINGEND SIZETYPE CLASS 1ST2ND3RD390 ORANGE WHITE BLACK 22AB391 ORANGE WHITE BROWN 22392 ORANGE WHITE RED 22TABLE 2 - TOOLS BINCO

10、DE INSTALLINGTOOL REMOVAL TOOL 390, 391, 392M81969/1-04 (GREEN) M81969/8-01 M81969/1-04 (WHITE) M81969/8-02 TABLE 3 - PART NUMBERS BIN CODE PART NUMBER SUPERSEDED PART NUMBER 390 M39029/71-390 M39029/71-1 391 M39029/71-391 M39029/71-2392 M39029/71-392 M39029/71-3 REQUIREMENTS: ALL REQUIREMENTS SHALL

11、 CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS39029. 1. DESIGN: CONTACTS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES. DIMENSIONS SHOWN APPLY AFTER PLATING. 2. TOOLS: TOOLS REQUIRED FOR THE INSTALLING/REMOVAL FROM THE CONNECTOR SHALL BE IN ACCORDANCE

12、 WITH TABLE 2. 3. PART NUMBERS: CONTACT PART NUMBERS SHALL BE IN ACCORDANCE WITH TABLE 3. SUPERSEDED PART NUMBERS ARE AS SPECIFIED. 4. MATERIALS: MATERIALS SHALL BE IN ACCORDANCE WITH AS39029. 5. MECHANICAL: WIRE WRAPPING: WIRE WRAPPING SHALL BE CLASS A AND WRAPPED IN ACCORDANCE WITH MIL-STD-1130. C

13、AUTION: MAINTAIN LIGHT TENSION ON THE WIRE AT THE START OF THE WRAP UNTIL ONE COMPLETE TURN HAS BEEN MADE. EDGE BURRS: WRAPPOST EDGE BURRS SHALL BE .0015 INCH (0.14 MM), MAXIMUM. 6. ELECTRICAL: ELECTRICAL REQUIREMENTS SHALL BE IN ACCORDANCE WITH AS39029. Copyright SAE International Provided by IHS u

14、nder license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/71SHEET 3 OF 3REV. A(R) CONTACTS, ELECTRICAL CONNECTOR, PIN, REMOVABLE, SOLDERLESS WRAPPOST TERMINATION (FOR MIL-DTL-38999 SERIES I, II, III AND IV, MIL-DTL-24308, MIL-D

15、TL-83733, AND MIL-DTL-55302/69 CONNECTORS) 7. ENVIRONMENTAL: ENVIRONMENTAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. 8. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS39029 AND MIL-STD-1130 FOR CLASS A WRAP. SUPPLIERS QUALIFIED TO AS39029/58 (M39029/58-362) NEED ONLY TEST IN ACCORD

16、ANCE WITH MIL-STD-1130 TO QUALIFY THIS CONTACT. THE MANUFACTURERS RELIABILITY ASSURANCE PROGRAM SHALL COMPLY WITH THE AS9100 AEROSPACE STANDARD FOR QUALITY MANAGEMENT SYSTEM REQUIREMENTS. OTHER ESTABLISHED AND INDUSTRY RECOGNIZED QUALITY ASSURANCE STANDARDS THAT ASSURE ALL PRODUCTS PRODUCED CONFORM

17、TO THE CONTRACT REQUIREMENTS ARE ACCEPTABLE. HOWEVER, IF USED, IT IS THE RESPONSIBILITY OF THE MANUFACTURER TO PROVIDE EVIDENCE OF COMPLIANCE TO AS9100. THE QUALIFYING ACTIVITY (QA) AUTHORITY RESERVES THE RIGHT TO MONITOR, MEASURE, AND VALIDATE COMPLIANCE AT THEIR DISCRETION. APPLICATION NOTES: 1. C

18、ONTACT MATES DIRECTLY WITH AN AS39029/57 SOCKET CONTACT AS SHOWN IN TABLE 4. TABLE 4 - CONTACT MATING PART NUMBERS AS39029/71 BIN CODE MATING AS39029 SLASH SHEET/BIN CODE -390, -391, -392 M39029/57-354, -355 1/, -356 1/1/ INACTIVE FOR NEW DESIGN 2. USAGE DATA (SEE TABLE 5): THESE CONTACTS ARE FOR US

19、E ONLY ON INTERNAL WIRING OF EQUIPMENT AND EQUIPMENT PANELS. FOR MIL-DTL-38999, USE IS RESTRICTED TO RECEPTACLES. WHEN USED IN RECOMMENDED CONNECTORS, THESE CONTACTS ASSURE THE USER OF AN ADEQUATE LENGTH FOR PROPER WRAPPING. 3. THIS CONTACT IS NOT FOR USE IN AS50881 APPLICATIONS. TABLE 5 - USAGE DAT

20、A CONNECTOR TYPE M39029/71 CONTACT USED MIL-DTL-38999 MS27499E MS27508E MS27513 SERIES II -390, -391, -392 MS27496 SERIES I MS27505 SERIES I -390, -391, -392 M38999/42 SERIES IV -390, -391, -392 MIL-DTL-24308/4 MIL-DTL-24308/8 MIL-DTL-55302/69 -390, -391, -392 MIL-DTL-83733/1 -392SPECIFICATION NOTES

21、: A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-