SAE AS 10051-1998 Hubs Conduit Connection Standard Dimensions《标准尺寸FSC 5975导管连接集线器》.pdf

《SAE AS 10051-1998 Hubs Conduit Connection Standard Dimensions《标准尺寸FSC 5975导管连接集线器》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 10051-1998 Hubs Conduit Connection Standard Dimensions《标准尺寸FSC 5975导管连接集线器》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、SAE-AS10051ADOPTION NOTICESAE-AS10051, “HUBS, CONDUIT CONNECTION, STANDARD DIMENSIONS“, wasadopted on 30-MAY-98 for use by the Department of Defense(DoD). Proposed changes by DoD activities must be submitted tothe DoD Adopting Activity: Commander, Naval Air Warfare Center,Aircraft Division, Code 414

2、100B120-3, Highway 547, Lakehurst, NJ08733-5100. Copies of this document may be purchased from theSociety of Automotive Engineers 400 Commonwealth DriveWarrendale, Pennsylvania, United States, 15096-0001. http:/www.sae.org/_Custodians: Adopting Activity:Navy - ASArmy - AVNavy - ASAir Force - 11FSC 5

3、975DISTRIBUTION STATEMENT A: Approved for public release; distributionis unlimited.Copyright 1998 Society of Automotive Engineers, Inc. Printed in the U.S.A.All rights reserved. .QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8510 FAX: (724) 776-0243 SAE WEB ADDRESS: http:/www.sae.org400 Commonwealth

4、Drive, Warrendale, PA 15096-0001SAE Technical StandardsBoard Rulesprovidethat:“Thisreport is published by SAEtoadvance thestateoftechnical and engineeringsciences. The useofthis reportisentirelyvoluntary, and its applicabilityand suitability for any particularuse, includingany patent infringement ar

5、ising therefrom, isthe soleresponsibility of the user.”SAE reviews each technical report at least every five years at whichtime it maybereaffirmed, revised, or cancelled. SAE invites your writtencomments and suggestions.SHEET 1 OF 3AS10051AEROSPACE STANDARDSubmitted for recognition as an American Na

6、tional StandardAS10051ISSUED1998-03HUBS, CONDUIT CONNECTION, STANDARD DIMENSIONSPREPARED BY SAE SUBCOMMITTEE AE-8A, SYSTEM INSTALLATIONFEDERAL SUPPLY CLASS 5975NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION AND10051 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES R

7、EQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE AND10051. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SA

8、E STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT

9、 CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.ANY MATERIAL RELATING TO QUALIFIED PRODUCT LISTS HAS NOT BEEN ADOPTED BY SAE. THIS MATERIAL WAS PART OF THE ORIGINAL MILITARY SPECIFICATION AND IS REPRINTED HERE FOR HISTORIC REF

10、ERENCE ONLY.400 Commonwealth Drive, Warrendale, PA 15096-0001AEROSPACE STANDARD AS10051SHEET 2 OF 3AS10051HUBS, CONDUIT CONNECTION, STANDARD DIMENSIONS400 Commonwealth Drive, Warrendale, PA 15096-0001AEROSPACE STANDARD AS10051SHEET 3 OF 3AS10051HUBS, CONDUIT CONNECTION, STANDARD DIMENSIONSREQUIREMEN

11、TS:1. THREADS TO BE IN ACCORDANCE WITH SPECIFICATION MIL-S-7742.2. CONDUIT HUBS MAY BE MADE AS SEPARATE THREADED INSERTS, SCREWED INTO OR OTHERWISE SECURED IN AN APPROVED MANNER TO THE EQUIPMENT. IN THE CASE OF THIN, SHEET, METAL TERMINAL BOXES, THE HUB SHOWN MAY BE WELDED ON INSTEAD OF BEING CAST I

12、NTEGRAL.3. THE INSIDE MACHINE SURFACE SHALL BE SMOOTH TO 125 MICROINCHES Ra PER ANSI B.46.1.NOTES:1. BREAK ALL SHARP EDGES AND REMOVE ALL HANGING BURRS AND SLIVERS WHICH MIGHT BECOME DISLODGED UNDER USAGE.2. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .005, ANGLES 1/2.

13、3. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE.4. REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS

14、 (DoDISS) SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN.5. THIS IS A DESIGN STANDARD, NOT TO BE USED AS A PART NUMBER.6. CHANGED FSC CLASS FROM “4730” TO “5975”.DASHNO.CONDUITSIZE (REF)TMIL-S-7742EMIN K RZMAX3 .1875 .5000-28UNEF-2A.3750.332 .167 .3534 .250

15、0 .6250-24UNEF-2A .394 .229 .4786 .3750 .7500-20UNEF-2A .519 .354 .5918 .5000 .8750-20UNEF-2A .669 .479 .63410 .6250 1.0000-20UNEF-2A .794 .604 .75912 .7500 1.1875-18UNEF-2A .929 .729 .95016 1.0000 1.4375-18UNEF-2A 1.214 .979 1.23520 1.2500 1.7500-18UNEF-2A .4370 1.469 1.229 1.49024 1.5000 2.0000-18UNEF-2A .5000 1.724 1.479 1.74528 1.7500 2.2500-16UN-2A 1.976 1.729 1.99732 2.0000 2.5000-16UN-2A .5620 2.229 1.979 2.25040 2.5000 3.0000-16UN-2A .6250 2.744 2.479 2.765