SAE AMS 4601A-2017 Aluminum Alloy Sheet and Plate 6 3Cu - 0 30Mn - 0 06Ti - 0 10V - 0 18Zr Solution Heat Treated Cold Worked and Naturally Aged (2219 -T31 -T351) (UNS A92219).pdf

《SAE AMS 4601A-2017 Aluminum Alloy Sheet and Plate 6 3Cu - 0 30Mn - 0 06Ti - 0 10V - 0 18Zr Solution Heat Treated Cold Worked and Naturally Aged (2219 -T31 -T351) (UNS A92219).pdf》由会员分享，可在线阅读，更多相关《SAE AMS 4601A-2017 Aluminum Alloy Sheet and Plate 6 3Cu - 0 30Mn - 0 06Ti - 0 10V - 0 18Zr Solution Heat Treated Cold Worked and Naturally Aged (2219 -T31 -T351) (UNS A92219).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther

2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this

3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49

4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS4601A AEROSPACE MATERIAL SPECIFICATION AMS4601 REV. A Issued 2011-07 Revised 2017-12 Supers

5、eding AMS4601 Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr Solution Heat Treated, Cold Worked and Naturally Aged (2219 -T31/-T351) (Composition similar to UNS A92219) RATIONALE AMS4601A revises Condition (3.2), Properties (3.3), Reports (4.4.1), Identification (5.1.1) and

6、 Packaging (5.2), and results from a Five-Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers an aluminum alloy in the form of sheet and plate 0.020 to 6.000 inches (0.551 to 152.4 mm), inclusive, in thickness (see 8.5). 1.2 Application This product form has bee

7、n used typically for structural parts requiring high strength up to 500 F (260 C) after proper precipitation heat treatment and which may require forming or welding during fabrication, but usage is not limited to such applications. 1.2.1 Certain design and processing procedures may cause these produ

8、cts to become susceptible to stress-corrosion cracking; ARP823 recommends practices to minimize such conditions. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier ma

9、y work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 4

10、00 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2355 Quality Assurance, Sampling and Testing Aluminum Alloys and Magnesium Alloy Wrought Products (Except Forging Stock), and Rolled, Forged, or Flash Welded

11、Rings SAE INTERNATIONAL AMS4601A Page 2 of 6 AMS2770 Heat Treatment of Wrought Aluminum Alloy Parts AMS2772 Heat Treatment of Aluminum Alloy Raw Materials ARP823 Minimizing Stress-Corrosion Cracking in Wrought Heat-Treatable Aluminum Alloy Products ARP1917 Clarification of Terms Used in Aerospace Me

12、tals Specifications 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM B594 Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace Applications ASTM B660 Packaging/Pack

13、ing of Aluminum and Magnesium Products ASTM B666/B666M Identification Marking of Aluminum Products 2.3 ANSI Accredited Publications Copies of these documents are available online at http:/webstore.ansi.org/. ANSI H35.1/H35.1M Alloy and Temper Designation Systems for Aluminum ANSI H35.2 Dimensional T

14、olerances for Aluminum Mill Products ANSI H35.2M Dimensional Tolerances for Aluminum Mill Products (Metric) 2.4 U.S. Government Publications Copies of these documents are available online at http:/quicksearch.dla.mil. QQ-A-250/30 Aluminum Alloy, 2219, Plate and Sheet 3. TECHNICAL REQUIREMENTS 3.1 Co

15、mposition Shall conform to the percentages by weight shown in Table 1, determined in accordance with AMS2355. Table 1 - Composition Element Min Max Silicon - 0.20 Iron - 0.30 Copper 5.8 6.8 Manganese 0.20 0.40 Magnesium - 0.02 Zinc - 0.10 Titanium 0.02 0.10 Vanadium 0.05 0.15 Zirconium 0.10 0.25 Oth

16、er Elements, each - 0.05 Other Elements, total - 0.15 Aluminum remainder SAE INTERNATIONAL AMS4601A Page 3 of 6 3.2 Condition Product shall be supplied in one of the following conditions as specified by purchaser. 3.2.1 Sheet Solution heat treated in accordance with AMS2772, cold worked and naturall

17、y aged to the T31 temper (see ANSI H35.1/H35/1M). 3.2.2 Plate Solution heat treated in accordance with AMS2772, stretched to produce a nominal permanent set of 2%, but not less than 1-1/2% nor more than 3%, and naturally aged to temper T351 (see ANSI H35.1/H35.1M). 3.2.2.1 Plate shall receive no fur

18、ther straightening operations after stretching. 3.3 Properties Product shall conform to the following requirements, determined on the mill produced size in accordance with AMS2355. In addition, test specimens in the T31 and T351 condition shall not be required to be tested within 4 days after comple

19、tion of the heat treatment. If the manufacturer so elects, samples may be tested after less than 4 days aging, but if they fail to show the specified properties, the test samples may be discarded, and additional specimens may be tested after 4 days aging. These specimens shall be taken from the same

20、 locations in the production lot or sample from which the prior specimens were taken. 3.3.1 As Received 3.3.1.1 Tensile Properties Shall be as shown in Table 2 (see 8.2). Table 2 Table 2A - Minimum tensile properties, inch/pound units Temper Nominal Thickness Inches Tensile Strength ksi Yield Streng

21、th at 0.2% Offset ksi Elongation in 2 inches or 4D % T31 0.020 to 0.039, incl Over 0.039 to 0.249, incl 46.0 46.0 29.0 28.0 8 10 T351 0.250 to 2.000, incl Over 2.000 to 3.000, incl Over 3.000 to 4.000, incl Over 4.000 to 5.000, incl Over 5.000 to 6.000, incl 46.0 44.0 42.0 40.0 39.0 28.0 28.0 27.0 2

22、6.0 25.0 10 10 9 9 8 Table 2B - Minimum tensile properties, SI units Temper Nominal Thickness Millimeters Tensile Strength MPa Yield Strength at 0.2% Offset MPa Elongation in 50.8 mm or 4D % T31 0.51 to 0.99, incl Over 0.99 to 6.32, incl 317 317 200 193 8 10 T351 6.35 to 50.80, incl Over 50.80 to 76

23、.20, incl Over 76.20 to 101.60, incl Over 101.60 to 127.00, incl Over 127.00 to 152.40, incl 317 303 290 276 269 193 193 186 179 172 10 10 9 9 8 SAE INTERNATIONAL AMS4601A Page 4 of 6 3.3.2 Response to Temper Conversion 3.3.2.1 Tensile Properties When specified, product in the T31 or T351 temper, af

24、ter precipitation heat treatment to the T81 or T851 temper respectively (see ANSI H35.1/H35.1M), shall have the properties shown in Table 3. The precipitation heat treatment shall be in accordance with AMS2772, but the actual aging treatment is considered proprietary. Table 3 Table 3A - Minimum tens

25、ile properties, inch/pound units Temper Nominal Thickness Inches Tensile Strength ksi Yield Strength at 0.2% Offset ksi Elongation in 2 inches or 4D % T81 0.020 to 0.039, incl Over 0.039 to 0.249, incl 62.0 62.0 46.0 46.0 6 7 T851 0.250 to 1.000, incl Over 1.000 to 2.000, incl Over 2.000 to 3.000, i

26、ncl Over 3.000 to 4.000, incl Over 4.000 to 5.000, incl Over 5.000 to 6.000, incl 62.0 62.0 62.0 60.0 59.0 57.0 46.0 46.0 45.0 44.0 43.0 42.0 8 7 6 5 5 4 Table 3B - Minimum tensile properties, SI units Temper Nominal Thickness Millimeters Tensile Strength MPa Yield Strength at 0.2% Offset MPa Elonga

27、tion in 50.8 mm or 4D % T81 0.51 to 0.99, incl Over 0.99 to 6.32, incl 427 427 317 317 6 7 T851 6.35 to 25.40, incl Over 25.40 to 50.80, incl Over 50.80 to 76.20, incl Over 76.20 to 101.60, incl Over 101.60 to 127.00, incl Over 127.00 to 152.40, incl 427 427 427 414 407 393 317 317 310 303 296 290 8

28、 7 6 5 5 4 3.3.3 Mechanical property requirements for product outside of the range covered by Tables 2 and 3 shall be agreed upon between purchaser and producer. 3.4 Quality Product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from

29、imperfections detrimental to usage of the product. 3.4.1 When specified, plate shall be subjected to ultrasonic inspection in accordance with ASTM B594, and shall meet the requirements shown in Table 4. Ultrasonic requirements for plate exceeding 4.500 inches thick shall be agreed upon by purchaser

30、and supplier. Table 4 - Ultrasonic class Nominal Thickness Inches Nominal Thickness Millimeters Class 0.500 to 1.499, incl 12.70 to 38.07, incl B Over 1.499 to 3.000, incl Over 38.07 to 76.20, incl A Over 3.000 to 4.500, incl Over 76.20 to 114.30, incl B SAE INTERNATIONAL AMS4601A Page 5 of 6 3.5 To

31、lerances Shall conform to all applicable requirements of ANSI H35.2 or ANSI H35.2M. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of the product shall supply all samples for producers tests and shall be responsible for the performance of all required tests. Purchaser

32、 reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests Composition (3.1), as-received tensile properties (3.3.1.1), precipitation heat treated tensile pro

33、perties (3.3.2.1), when specified, ultrasonic inspection (3.4.1) and tolerances (3.5) are acceptance tests and except for composition, shall be performed on each inspection lot. 4.3 Sampling and Testing Shall be in accordance with AMS2355. 4.4 Reports The producer of the product shall furnish with e

34、ach shipment a report stating that the product conforms to the composition, tolerances, and ultrasonic testing when specified, and showing the numerical results of tests on each inspection lot to determine conformance to the other acceptance test requirements. This report shall include the purchase

35、order number, inspection lot numbers, condition, AMS4601A, size, and quantity. The report shall also identify the producer, the product form, and the size of the mill product. 4.4.1 When material produced to this specification, is beyond the sizes allowed in the scope or tables or other exceptions a

36、re taken to the technical requirements listed in Section 3 (see 5.1.1), the report shall contain a statement “This material is certified as AMS4601A(EXC) because of the following exceptions.” and the specific exceptions shall be listed. 4.5 Resampling and Retesting Shall be in accordance with AMS235

37、5. 5. PREPARATION FOR DELIVERY 5.1 Identification Shall be in accordance with ASTM B666/B666M. SAE INTERNATIONAL AMS4601A Page 6 of 6 5.1.1 When technical exceptions are taken (see 4.4.1), the material shall be marked with AMS4601(EXC). 5.2 Packaging 5.2.1 Product shall be protected from damage duri

38、ng storage and shipment by a method determined by producer unless specified by purchaser. Examples of typical protective methods include, but are not limited to interleaving with paper or oiling of the surface. 5.2.2 Product shall be prepared for shipment in accordance with ASTM B660 and in complian

39、ce with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A producer shall mention this specification number and its revision letter in all quotations and when acknowledging purc

40、hase orders. 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 Revision Indicator A change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revisio

41、ns, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain edi

42、torial changes only. 8.2 Properties in Tables 2 and 4 were not substantiated according to AMS statistical analysis procedures, but were taken from U.S. Federal Specification QQ-A-250/30. 8.3 Terms used in AMS are clarified in ARP1917. 8.4 Dimensions and properties in inch/pound units and the Fahrenh

43、eit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not less than the following: AMS4601A Condition of product desired Product form and size of product desired Property and acceptance requirements from the cognizant engineering organization applicable to sizes outside the range listed in 1.1. Quantity of product desired PREPARED BY AMS COMMITTEE “D”