SAE AIR 1082C-2013 Fluid-System-Component Specification Preparation Criteria《流体系统组件规格制备标准》.pdf
《SAE AIR 1082C-2013 Fluid-System-Component Specification Preparation Criteria《流体系统组件规格制备标准》.pdf》由会员分享,可在线阅读,更多相关《SAE AIR 1082C-2013 Fluid-System-Component Specification Preparation Criteria《流体系统组件规格制备标准》.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2013 SAE International All rights reserved. No part of this pub
3、lication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970
4、(outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AIR1082CAEROSPACEINFORMATION REPORT AIR1082 REV. CIssued 1970-05 Revised 1992-02 Rea
5、ffirmed 2007-12 Stabilized 2013-10 Superseding AIR1082B Fluid-System-Component Specification Preparation Criteria RATIONALEThe document as written does not represent a safety or health issue which per document rules disallow cancellation. The value of an updated AIR1082B would be limited because ARP
6、4754 was recently updated and offers guidance on specifying fuel system and equipment and MIL-STD-461e already offers guidance on specification format and production. This document will, therefore, be stabilized. STABILIZED NOTICE This document has been declared “Stabilized“ by the SAE AE-5A Aerospa
7、ce Fuel, Inerting and Lubrication System Committee and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability of technical requirements. Newer technology may exist. Copyright SAE International Provided by IHS under licen
8、se with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE INTERNATIONAL AIR1082C Page 1 of 17 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE INTERNATIONAL
9、 AIR1082C Page 2 of 17 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE INTERNATIONAL AIR1082C Page 3 of 17 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo repro
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAIR1082C2013FLUIDSYSTEMCOMPONENTSPECIFICATIONPREPARATIONCRITERIA 流体 系统 组件 规格 制备 标准 PDF

链接地址:http://www.mydoc123.com/p-1019953.html