NEMA C29 8-1985 Wet Process Porcelain Insulators Apparatus Cap and Pin Type《湿法工艺制瓷绝缘子(帽式和针式装置型)[代替 ANSI C29 8 ANSI C29 8 ANSI C29 8]》.pdf

《NEMA C29 8-1985 Wet Process Porcelain Insulators Apparatus Cap and Pin Type《湿法工艺制瓷绝缘子(帽式和针式装置型)[代替 ANSI C29 8 ANSI C29 8 ANSI C29 8]》.pdf》由会员分享，可在线阅读，更多相关《NEMA C29 8-1985 Wet Process Porcelain Insulators Apparatus Cap and Pin Type《湿法工艺制瓷绝缘子(帽式和针式装置型)[代替 ANSI C29 8 ANSI C29 8 ANSI C29 8]》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI/NEMA C29.8-1985 (R2002, R2012) American National Standard Wet Process Porcelain Insulators Apparatus, Cap and Pin Type ANSI/NEMA C29.8-1985 (R2002, R2012) American National Standard Wet Process Porcelain Insulators Apparatus, Cap and Pin Type Secretariat: National Electrical Manufacturers Asso

2、ciation Approved: August 2012 Published: May 20, 2013 American National Standards Institute, Inc. C29.8-1985 (R2002, R2012) Page ii Copyright 2013 by National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consen

3、sus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. American National Standards Institute (ANSI) standards and

4、guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA ad

5、ministers the process and establishes rules to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and gui

6、deline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA discla

7、ims and makes no guaranty or warranty, express or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the

8、 performance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to per

9、form any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other s

10、tandards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document.

11、NEMA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health or safetyrelated information in this document shall not be attributable to NEMA and is solely the responsibility of the certif

12、ier or maker of the statement.C29.8-1985 (R2002, R2012)Page iii Copyright 2013 by National Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by ANSI that the requirements for due process, consensus, and other criteria for

13、approval have been met by the standards developer. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much more than a simple majority, but not necessa

14、rily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The use of American National Standards is completely voluntary; their existence does not in any respect preclude anyone, whether he has approved the standards

15、or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no per

16、son shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard. Caution No

17、tice: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current informati

18、on on all standards by calling or writing the American National Standards Institute. Published by National Electrical Manufacturers Association 1300 North 17th Street, Rosslyn, VA 22209 g164 Copyright 2013 by National Electrical Manufacturers Association All rights reserved including translation int

19、o other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American Copyright Conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or

20、otherwise, without the prior written permission of the publisher. Printed in the United States of America. C29.8-1985 (R2002, R2012) Page iv Copyright 2013 by National Electrical Manufacturers Association FOREWORD (This foreword is not part of American National Standard C29.8-1985 (R2002, R2012) The

21、 first edition of this standard was essentially based on the EEI-NEMA Standard Wet-Process Porcelain Insulators (Apparatus, Cap and Pin Type), EEI TDJ-58, NEMA 146-1956. (EEI is the Edison Electric Institute; NEMA is the National Electrical Manufacturers Association). Subsequent revisions were devel

22、oped by the American National Standards Committee on Insulators for Electric Power Lines, C29. This standard has been revised four times by the C29 Committee. The principal differences between this revision and the 1980 edition include: 1) moving packing recommendations to the Appendix 2) changing t

23、he description of the test for ferrous metal parts galvanizing 3) replacing the figures with a table of dimensions and characteristics 4) requiring electrical tests to be made on completely assembled insulators This standard was processed and approved for submittal to ANSI by Accredited Standards Co

24、mmittee on Insulators for Electric Power Lines, C29. Committee approval of the standard does not necessarily imply that all committee members voted for approval. At the time it approved this standard, the ASC C-29 Committee had the following members: Rob Christman, Chairman Steve Griffith, Secretary

25、 Organization Represented: Name of Representative: Edison Electric Institute B. Freimark R. ChristmanE. Cleckley M.GarlsW. Avey J. Varner (alt) R. Kluge (alt) G. Obenchain (alt) Institute of Electrical and Electronic Engineers T. Grisham J. Hildreth A. Jagtiani J. KuffelA. Phillips E. Gnandt (alt) N

26、ational Electrical Manufacturers Association P. Maloney A. BakerR. A. Bernstorf G. Powell G. A. Stewart E. Kress (alt)Z. Lodi (alt) E. Niedospial (alt) A. Schwalm (alt) Tennessee Valley Authority J. Nelson Western Area Power Administration R. Clark C29.8-1985 (R2002, R2012) Page v Copyright 2013 by

27、National Electrical Manufacturers Association TABLE OF CONTENTS Page FOREWORD .iv 1 SCOPE . 1 2 REFERENCED STANDARDS 1 2.1 American National Standards 1 2.2 Other Standard 1 3 DEFINITIONS 1 4 GENERAL 1 5 MATERIAL . 1 6 DIMENSIONS AND CHARACTERISTICS . 2 7 MARKING 4 8 SAMPLING, INSPECTION, AND TESTS

28、4 8.1 General4 8.2 Design Tests . 4 8.2.1 Low-Frequency Wet Withstand 4 8.2.2 Critical-Impulse Flashover, Positive. 4 8.2.3 Impulse Withstand. 4 8.2.4 Radio-Influence Voltage . 4 8.2.5 Compression Strength . 4 8.2.6 Thermal Shock . 4 8.3 Quality Conformance Tests . 4 8.3.1 Visual and Dimensional Tes

29、ts 4 8.3.2 Porosity Test . 5 8.3.3 Galvanizing Test . 5 8.3.4 Cantilever-Strength 5 8.3.5 Torsional Strength . 5 8.3.6 Tensile Strength . 5 8.3.7 Puncture5 8.4 Routine Tests . 5 8.4.1 Tension Proof . 5 8.4.2 Flashover5 TABLES 1 Dimensions and Characteristics of Cap-and-Pin Type Apparatus Insulators

30、. 3 APPENDIX. 6 C29.8-1985 (R2002, R2012) Page vi Copyright 2013 by National Electrical Manufacturers Association C29.8-1985 (R2002, R2012) Page 1 Copyright 2013 by National Electrical Manufacturers Association Wet Process Porcelain InsulatorsApparatus, Cap and Pin Type 1 SCOPE This standard covers

31、outdoor high-voltage cap-and-pin type apparatus insulators made of wet-process porcelain and used in the transmission and distribution of electrical energy. 2 REFERENCED STANDARDS 2.1 American National Standards. This standard is intended for use in conjunction with the following American National S

32、tandards. When these standards are superseded by a revision approved by the American National Standards Institute, Inc. the revision shall apply. ANSI C29.1-1988 (R2012) Test Methods for Electrical Power Insulators ANSI Z55.1-1967 (R1973) American National Standard Gray Finishes for Industrial Appar

33、atus and Equipment 2.2 Other Standard. This standard is intended for use in conjunction, ASTM A153-82 with Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware. 3 DEFINITIONS 3.1 See section 2 of ANSI C29.1-1988 (R2012) for definitions of terms. 3.2 In this standard, the word insulato

34、r shall refer to a unit or to a stack of two or more units. 3.3 The technical reference numbers appearing in Table 1 are a widely used and recognized identification series for apparatus insulator units or stacks. 4 GENERAL 4.1 Insulators shall conform in all respects to the requirements of this stan

35、dard. The text and figures supplement each other and shall be considered part of this standard. 4.2 Manufacturers drawings, if furnished, shall show the outline of the insulators, together with all pertinent dimensions. Any variations in these dimensions due to manufacturing tolerances shall be indi

36、cated. 5 MATERIAL 5.1 The insulators shall be made of good commercial-grade wet-process porcelain. AM ERICAN NAT IO NAL ST ANDARD ANSI/NEMA C29.8-1985 (R2002, R2012) C29.8-1985 (R2002, R2012) Page 2 Copyright 2013 by National Electrical Manufacturers Association 5.2 The entire surface of the insulat

37、or, with the exception of a firing surface, shall be glazed. The entire surface shall be relatively free from imperfections. Color is not a part of this standard. If gray is required, it shall be in accordance with ANSI Z55.1-1967 (R1967) and conform to Munsell notation 5BG 7.0/0.4 with the followin

38、g tolerances: 1) Hue: 12 (3G to 7B) 2) Value: 0.5 3) Chroma: -0.2 to +0.6 5.3 Metal parts shall be made of a good commercial grade of malleable iron, ductile iron, steel, or aluminum. Ferrous parts other than stainless steel shall be galvanized in accordance with ASTM A153-82. 6 DIMENSIONS AND CHARA

39、CTERISTICS 6.1 Dimensions and characteristics shall be in accordance with table 1. 6.2 Shell diameters given for insulators listed in table 1 shall not be exceeded by more than 3 percent to ensure physical clearances in assembled apparatus . 6.3 Minimum dimensions are limited by other specified char

40、acteristics . 6.4 The length tolerance for any individual unit shall be 1/32 inch. C29.8-1985 (R2002,R2012) Page 3 Copyright2013 byNational Electrical ManufacturersAssociation Table1Dimensionsand CharacteristicsofCap-And-Pin TypeApparatusInsulatorsRadio-Influence-VoltageDataNum-Maxi-CantileverTechni

41、calReferenceNumberberofHeightmum CapBoltCircleStrength(lb)Com-Low-FrequencyMaximum RIVLow-LeakageLow-FrequencyCriticalImpulseTechnicalReferenceUnits.perDiam-Diam-Diam-TensileTorsionalpressionTensionTest(VatFrequencyDis-WetImpulseFlashover. perStackStack (in)eter(in)eter(in)eter1(in)UprightUnderhungS

42、trength (lb)Strength (in-lb)Strength (lb)Proof(lb)Voltage (kV)1000 kHz)Puncture(kV)tance2(in)Withstand3(kV)Withstand3(kV)Positive(kV)NumberStackUnitStackUnit117-1/27532000100050006000100001250550807-1/23095105141108532000100050007000100001250105011512451101254711210-1/2632000100050008000100001250151

43、001452060150170710115136320001000700010000150001750221001952880200225_1013118147-5/832000100080001200015000200030200225361002502801316147229148315001000120001500025000442005214535039016147411896-1/2540003000100001200020000200055090830951054144110106-3/454000300010000140002000020001050115144511012544

44、461121285400030001000016000200002000I510014518601501704649115148-1/454000300014000200003000020002210019528802002254956140229179-3/453000235020000400006000044200661603504105614019140343-1/2179-3/451700147020000400006000073200992305506101914025140458179-3/45120010702000040O0060000103500132315750810251

45、401231414581810-7/8520001750250009000075000103500132315750810123141126140572-1/2179-3/45910840200004000060000125500165385900101012614027141572-1/21810-7/8514501350250009000075000125500165385900101027141128140687179-3/4575070020000400006000014650019845510501210128140281416871810-7/8511701100250009000

46、07500014650019845510501210281411291426871810-7/8711701100250009000075000146500198455105012101291421331427101-1/21810-7/87100095025000900007500018010002315251300141013314213514281161810-7/87900860250009000075000210100026459014701610135142147114-1/214833000200012000150002500020002210019526701902101471

47、40114-1/2179-3/45700040002000040000600002000221002153375210235140141114-1/21810-7/851000060002500090000750002000221002153375210235141142114-1/21810-7/871000060002500090000750002000221002153375210235142191114-1/21810-7/8720000120004000012000010000020002210021533752102351911961916871810-7/872300230040

48、000120000100000146500198455105012101961911971917101-1/21810-7/87200020004000012000010000018010002315251300141019719119819181161810-7/871750175040000120000100000 210100026459014701610198191139114-1/2179-3/451000060002500090000750002000221002153375210235139174139458179-3/452000175025000900007500010350

49、0132315750810174139175139572-1/2179-3/45145013502500090000750001255001653859001010175139176139687179-3/451170110025000900007500014650019845510501210176139164114-1/2147-5/83400035001200030000600002000221002253375210235164166164229147-5/83200020001200030000600004420066160350410166164167164343-1/2147-5/83100010001200030000600007320099230550610167164168164458147-5/83100010001200030000600001035001323157S0810168164165118147