NAVY MIL-T-82535-1968 TIMER INTERVAL MARK 11 MOD 2 (ASSEMBLY)《集合11号2模时间间隔定时器》.pdf

《NAVY MIL-T-82535-1968 TIMER INTERVAL MARK 11 MOD 2 (ASSEMBLY)《集合11号2模时间间隔定时器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-T-82535-1968 TIMER INTERVAL MARK 11 MOD 2 (ASSEMBLY)《集合11号2模时间间隔定时器》.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-T-82535 13 m 7777706 03bL2b 7 m Superseding NOTS Xs 546 Rev. C 29 September 1967 MILITARY SPECIFICATION FOR TIMER, INTERVAL MARK 11 MOD 2 (ASSEMBLY) This gpecification has been approved by the Naval. Ordnance Sysfems Command, Department of the Navy 1, SCOPE 1.1 This specification establishes t

2、he requirements of one type of Interval Timer Mark 11 Mod 2 Assembly, (See 6.1 for intended use and description. ) 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on the date of invitation for bids, fofm a part of this specification to the extent specified herein, except

3、as noted, SPECIFICATIONS FEDERAL PPP-B-62 1 MILITARY MIL-P-116 MIL-L-10547 Boxes, Wood, Nailed and Lock-Corner Preservation, Methods of Liners, Case, and Sheet, verwrap; Water-Vaporproof or Waterproof, Flexible s _L / THTS DOCUMENT CONTAINS 23 PAGES. 74-O Provided by IHSNot for ResaleNo reproduction

4、 or networking permitted without license from IHS-,-,-MIL-T-$2535 (OS) STANDARDS FEDERAL FED -STD-102 Preservation, Packaging, and Packing Levels MILITARY MIL-STD-105 D Sampling Procedures and Tables for inspection by Attributes MIL-STD-129 Marking for Shipment and Storage MIL -STD - 167 Mechanical

5、Vibrations of Shipboard Equipment DRAWINGS BUREAU OF NAVAL WEAPONS LD 540655 Tester, Timer, T-3077 (Assembly) LD 541525 Timer, Interval, Mk 11 Mod 2, Assembly and all documents listed thereon PUBLICATIONS BUREAU OF NAVAL WEAPONS OD 12996 Operation and Maintenance of the Inter- val Timer Test Set T-3

6、077 (Copies of specifications, standards, drawings, and publications requested by contractors in connection with specific procurement functions should be ob- tained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1 General requirements. Unless otherwise spec

7、ified in the contract or order, all materials and treatments of materials and parts used in the manu- facture of the timer shall be in accordance with the requirements specified here- in and with the applicable documents listed in BuWeps LD 541525. in the manufacture of the timer shall comply with t

8、he requirements of their respective drawings and shall be tested as specified in Section 4 (see 4.2). 3.1.1 Electrical component requirements. Electrical components used Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-2535 13 777770b 0361828 O

9、m MIL-T-82535 (OS) 3.2 Preproduction samples. Unless otherwise specified in the contrabt or order, preproduction samples of the timer shall be manufactured using the methods and procedures proposed for production, The sample shall be tested as specified in Section 4 herein, and is for the purpose of

10、 determining that, prior to starting production, the contractor s production methods are capable of yielding items that comply with the technical requirements of the contract. 3.3 Performance and product characteristics, The timer shall meet the following performance and product characteristics. 3.3

11、.1 Time intervals. With 24 to 32 volts DC applied, the timer shall produce electrical output pulses at two separate, predetermined time intervals (measured from the instant of voltage application) while stabilized at the follow- ing temperatures: a. Plus 35 plus 5 minus O degrees F, for not less tha

12、n 4 hours b. Plus 80 plus or minus 15 degrees F, for not less than 4 hours c. Plus 120 plus O minus 5 degrees F, for not less than 4 hours 3.3.1.1 Timer interval, 12.5 seconds. Before experiencing any test of 4.5, the timer shall produce an electrical output pulse at 12.5 plus or minus O. 60 seconds

13、, After experiencing any test of 4.5, the timer shall produce an electrical output pulse at 12.5 plus or minus 1.0 seconds. The 12.5-second time interval shall remain within the specified limits when random noise as indicated in Figure 1 appears on the DC input. The noise voltage spikes shall have a

14、 duration of 15 plus or minus 5 microseconds# a frequency of 1000 plus or minus 100 cycles per second (cps), and an amplitude of 17 volts above or below the input DC level. Duration of the noise voltage spikes shall be measured at O. 10 Vs above or below the input DC level, specified in 4.5, the tim

15、er shall produce an electrical output pulse at 18.5 plus or minus 0.90 seconds. After experiencing any test of 4.5, the timer shall pro- duce an electrical output pulse at 18.5 plus or minus l. 5 seconds * 3.3.1.2 Timer interval, 18.5 second. Before experiencing any test 3.3.2 Energy output. The ene

16、rgy output of the electrica1 pulses of 3.3.1 shall be not less than 10,500 ergs through a resistance of 5 ohms during the first millisecond, with a peak amplitude of 5 volts DC minimum. 3.3.3 Premature output pulse. Interruption of input voltages shall not cause the 18.5-second interval section of t

17、he timer to moduce the oubut Dulse I specified in 3.3.1.2 before the predetermined time interval has elapsed. 3.3.4 Leakage current. The leakage current between the output leads and the ground leads of the 12.5-second and the 18.5-second time interval sections of the timer, measured through a resist

18、ance of 5 ohms, shall be not more than 5 milliamperes prior to the electrical output pulse. _c_L_ 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-82535 (OS) t (3 vs SPIKE- DURATIO 1 o .iovs 7- - SPIKE FREQUENCY Provided by IHSNot for ResaleNo

19、 reproduction or networking permitted without license from IHS-,-,- MIL-T-82535 (OS) 3.4 Environmental requirements. Unless otherwise specified, the timer shall be capable of conforming to the performance and product characteristics of this specification after being exposed to the environments and a

20、ll conditions specified herein. 3.4.1 Temperature. 3.4.1.1 Operating condition. The timer shall meet the performance and product characteristics while at temperatures from 35 to 120 degrees F. 3.4.1.2 Storage condition. The timer shall withstand temperatures from minus 65 to plus 160 degrees F. 3.4.

21、2 Vibration. 3.4.2.1 Standby condition. The timer shall withstand vibration as speci- fied for Type I equipment in MIL-STD-167 up to 25 cps. 3.4.2.2 Operating condition. The timer shall withstand vibration through a frequency range of 20 to 2000 cps at O. IO-inch double amplitude or log (g = unit of

22、 gravitational acceleration) whichever is less. The timer shall meet the requirement of 3.3.1.1 and 3.3.1.2 while being subjected to this environment and thereafter shall meet the performance andproduct characteristics of this specification. 3.4.3 Shock. 3.4.3.1 Standby condition. The timer shall wi

23、thstand shocks of 40g peak magnitude. The shock shall have a pulse shape approximating a one-half sine wave having a duration of 5 milliseconds. 3.4.3.2 Operating condition. 3.4.3.2.1 Major. The timer shall withstand a shock of 2400g peak mag- nitude. The shock shall have a pulse shape approximating

24、 a one-half sine wave having a duration of 1.00 plus or minus O. 25 millisecond. The shock shall be applied in the direction shown in Figure 2 when the 18.5-second timer section has operated 9 plus or minus 3 seconds, The 18.5-second timer section shall meet the requirement of 3.3.1.2 while being su

25、bjected to this shock, and the 12.5-second timer section shall meet the requirements of 3.3.1.1 immediately after the shock. The timer shall thereafter meet the performance and product characteristics of this specification. 3.4.3.2.2 Minor. The timer shall withstand two shocks of 1200g peak magnitud

26、e each. The shocks shall have a pulse shape approximating a one-half sine wave having a duration of 1. O plus or minus O. 25 millisecond. The shocks shall be applied once in each direction, as shown in Figure 2, when the 18.5- second timer section has operated 9 plus or minus 3 seconds, The 18.5-sec

27、ond Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-T-82535 13 m 777770b 036118311 O m MIL-T-82535 (OS) Figure 2. Environmental Testing Axes Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

28、T-82535 13 M 7777706 0361832 2 M MIL-T-82535(0C) timer section shall meet the requirements of 3.3,l. 2 while being subjected to these shocks, and the 12.5-second timet section shall meet the requirements of 3.3.1.1 immediately after these shocks. The timer shalf thereafter meet the performance and p

29、roduct characteristics of this specification. 3.4.4 Acceleration. The timer shall withstand an acceleration of 25g for 4 seconds minimum,* applied in the direction shown in Figure 2. 3.5 Workmanship. The workmanship and finish shall he of sufficiently high grade to assure satisfactory operation cons

30、istent with the requirements of this specification. All parts used in the assembly shall be thoroughly clean and free of excess materials, chips, and loose or splattered foreign materiais. The standards of workwanship exhibited in any approved preproduction sample, sub- ject to-any . qualification s

31、tated in the Government s notice of approval, shall be determinative of the requirements of the contract relative to workmanship insofar as not specifically covered by applicable specifications. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con-

32、 tract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory acceptable to the Government. The Government reserves the right to per

33、form any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 fied as follows: Classification of inspecliion. riispection of the timer shall be classi- a. Preproduction and periodic produ

34、ction inspection (See 4.5.) b. Quality conformance inspecion* (See 4.6.) c. Electrical component inspection (See 4.7 and 6.3.2.) 4.3 Sampling. (See 6.2.1.) 4.3.1 Lot size. The term ?lott1 shall mean “inspection lot1?, that is, a collection of product submitted by a supplier for inspection. Unless ot

35、herwise specified in the contract or order, the number of product in each lot shall be three hundred (300). 4.3.2 Preproduction sample. A preproduction sample of fifteen (15) timers, manufactured in accordance with 3.2, shall be subjected to the preproduction tests detailed in 4.5. Acceptance of the

36、 preproduction sample shall be based on no defects in the sample. Further production of the timer by the supplier, prior to approval of the preproduction sample, shal be at the supplier s risk. e- / Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-825

37、35 13 W 9999906 361833 4 W MIL-T-82535 (OS) 4.3.3 Periodic production sample. From each succeeding lot of three hundred (300) or less timers, a random sample of ten (10) timers shall be se- lected. These sample units shall be subjected to the tests of 4.5. The timers shall be considered satisfactory

38、 if they meet all specification and pertinent drawing requirements and withstand the tests specified in 4.5. (See Table I.) When a defective unit is found in any lot, acceptance of all units in the lot shall be wichheld and the contractor shall: a. Determine the cause of the defect. b. Take the nece

39、ssary action, with the concurrence of the procur- ing activity5 to correct or eliminate the defect from all units in the lot and, if so directed by the procuring activity, from those units previously shipped, c. Submit to the procuring activity for approval, the proposed cor- rective action to preve

40、nt recurrence of the defect, 4.3.4 Quality conformance inspection sampling. Samples shall be selected as specified in 4.6 and shall be used to determine the acceptability of the timer inspected as specified in 4.6. Table I. Preproduction and Periodic Production Test Sequence Paragraph Test Quantitie

41、s Test Number: Preproduction Periodic Quality Conformance Inspection 4.6 15 10 Temperature, Storage Condition 4.5.1.1 15 10 Quality Conformance Inspection 4.6* 15 10 Vibration, Standby Condition 4.5.1.2 15 10 Quality Conform ance Inspec tion 4.6* 15 10 Shock, Standby Condition 4.5.1.3 15 10 *Time in

42、terval tests of 4.6.1.1 shall be conducted only at plus 80 plus or minus 15 degrees F. P Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- MIL-T-2535 (OS) Table I. Preproduction and Periodic Production Test Sequence (Continued) Paragraph Test Quanti

43、ties Test Number Preproduction Periodic Quality Conformance Inspection 4.6* 15 10 Acceleration 4.5.1.4 15 10 Vibration, Operating Condition 4.5.1.5* 15 10 Quality Conformance Inspection 4.6* 15 10 Shock, Operating Condition 4.5.1.6* 15 10 Quality Conform ance Inspection 4.6* 15 10 Temperature, Opera

44、ting Condition 4.5.1.7 15 10 Low Extreme 4.5.1.7.1 15 10 Quality Conformance Inspection 4.6* 15 10 High Extreme 4.5,1.7.2 15 10 Quality Conformance Inspection 4.6* 15 IO _. - *Time interval test of 4.6.1.1 shall be conducted only at plus 80 plus or minus 15 degrees F. *Time interval tests 4.6.1.1.1

45、and 4.6.1.1.2 shall be performed during en- vironmental tests; thereafter, the remaining quality conformance inspection test shall be performed. *Time interval test 4.6.1.1.2 shall be performed during the environmental test; thereafterr the remaining quality conformance inspection tests shall be per

46、formed. (See 4.5.1.6.1 and4.5.1.6.2,) *Perform quality conformance inspection 4.6 only at plus 35 plus 5 minus O degrees F. *Perform quality conformance inspection 4.6 only at plus 120 plus O minus 5 degrees F. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

47、om IHS-,-,-7 MIL-T-82535 13 W 7777706 O361835 8 MIL-T-82535 (OS) 4.4 Test equipment and test conditions. 4,4.1 Qualitv conformance inspection test equipment. The following items of test equipment are required to perform the quality conformance inspection: Equipment Capability a. Tester, Timer T-3077

48、 Conform to ID 540655 (Assembly) Operate in accordance with OD 12996 b. Temperature chamber Maintain temperature .at :.: Plus 35 plus 5 minus O degrees F Plus 80 plus or minus 15 degrees F Plus 120 plus O minus 5 degrees F 4.4.2 Preproduction and periodic production test equipment. The following ite

49、ms of test equipment, in addition to selected items of quality conformance inspection equipment and pieces of equipment recommended by applicable speci- fications or standards referenced within test procedure paragraphs$ are required to perform the preproduction and periodic production tests: Equipment Capability a. Temperature chamber Maintain empe