NAVY MIL-P-23810 A-1967 PANEL COMPONENT RECORDING (FOR TORPEDO EXERCISE SECTION MARK 64 MOD 2)《MARK 64 MOD 2鱼雷实验部分仪表面板和组元逐帧录像法》.pdf
《NAVY MIL-P-23810 A-1967 PANEL COMPONENT RECORDING (FOR TORPEDO EXERCISE SECTION MARK 64 MOD 2)《MARK 64 MOD 2鱼雷实验部分仪表面板和组元逐帧录像法》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-P-23810 A-1967 PANEL COMPONENT RECORDING (FOR TORPEDO EXERCISE SECTION MARK 64 MOD 2)《MARK 64 MOD 2鱼雷实验部分仪表面板和组元逐帧录像法》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、RIL-P-2383OA L3 Ob 0303836 O _ MIL-P-23810A( OS) i November 1967 Superseding MIL-P- 23810( wep ) PAXEL, COMPoNErlT, mcoRDrNG (For Torpedo Ekercise Section Mark 64 Wd 2) This specification has been approved by the Naval. Ordnance Systems Cornand, Department of the Navy 1. SCOPE 1.1 Scope. This specif
2、ication describes the requirements for the procv- ment, inspection, and test of a recording panel, ED 613310. 2. ApPLICAJ3rn DOoMENTS 2.1 The following documents of the issue in effect on the date of invita- tion for bids or request for proposal form a park of this specification to the extent specif
3、led herein. SPECIFIC ATIONS MXLITrnY 1-0-23560/4 Oscillograph STANDARDS MILTJX?lY m-m-10s Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage MI3-STD-129 DRAWINGS NAVAL ORDNANCE SYSCEMS CONMAFD rn 162756 Shipping (packing) Condition rn 613310 Record5ng Compon
4、ent Panel Assembled Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-2381OA 13 7777706 0303838 4 % MIL-P- 238ioA(0S) . . . 1-0-23560/4, which recor
5、ds the information for later study of the tor- pedos behavior during a run. power supply which furnishes power to all the signal source points that are dc energized. The recording panel also contains a dc 3.2 General requirements 3.2.1 Contractor-furnished data. Data required by this specification o
6、r by applicable documents referenced in Section 2 need not be furnished unless specified in the contract or order (see 6.2). 3.2.2 Preproduction samples. Unless otherwise specified in the con- . tract or order, preproduction samples of the recording panel shall be manufactured using the methods and
7、procedures proposed for the produc- tion lot. and are for the purpose of determining that the production item meets the requirements of this specification and the design. Provisions of samples shall be in accordance with 4.2.1. These samples will be tested as specified in Section 4 herein, 3.2.3 Mat
8、erials. Unless otherwise specified in the contract, requi- sition, or order, all materials and purchased parts entering into the final assembly of the recording panel shall conforpi strictly to the de- tailed requirements indicated on the drawings and specifications listed in LD 613310. . . . 3.2.4
9、Finishes, coatings, construction, and dimensions . Finishes, :.Y: coatings, construction, and dimensions for the recording panel shail be strictly in accordance with the appl5cable draxiilgs, specifications, and publications listed in T;D 613310, 3.2.5 Moisture, fungus, and corrosion. The recording
10、panel shall be rendered moisture, fungus, and corrosion resistant as required by os 6341. 3.2.6 Marking. Marking of assemblies, subassemblies, and parts shall be in accordance with the applicable drawings listed in LD 613310. 3.2.7 Interchangeability. Component parts of the assembled units (unless o
11、therwise specified on the applicable drawings ) fabricated in strict accordance with their applicable drswings shall be interchange- able and shall assemble with mating components of the unit without selection or fitting. a Wt, selection or fitting is required, then changes in dimensions me necessar
12、y and revision and correction of the applicable drawings is required. See 3.2.10. If, during assembly of the fabricated parts of 3.2.8 Gages. The contractor shall provide himself with whatever -=l-q 3 . -. t.I:. I . - “ A I I . , . i. . i- i -.-. - - L -. e d . i . -.- -. - -. _- . _ . . . -. -I ; .
13、 C. L . .:.:.-:. . 1 . - . ,.-_-I . - ., .- * ,. .- .-. L . i , . . l. Y_. - ,._-.- - re.- -. I -.-* . -. . _ .- -.-L . I.- . -.* . -_ -. . . w - .-._.- *“ . !, 1 . .- . -._. .- . ,-_ -.-.-.-. . . - . _-.- -.-._ . “ I .-. . . -,. . . . - . . . . . . . . , . Provided by IHSNot for ResaleNo reproducti
14、on or networking permitted without license from IHS-,-,- flIL-P-23810A 33 m 77777Ob 0303837 b pertinent Navy Final Inspection Gages for guidance in the design of the contractors inspection gages. However, such procedure shall not serve to relieve the contractor of is responsibility in the design and
15、 man- ufacture of such gages as may be reqdred in the satisfactory fulfill- ment of the contract requirements, but is intended-to facilitate ac- ceptance of all components and assemblies by Navy Final Inspection Gages. 3.2.9 Threads. Unless otherwise specified, all threads shall be in accordance wit
16、h National Bureau of Standards Handbook 28. fit for threads shall be as specified on the applicable drawings. The class or 3.2.10 Conflicting requirements . Conflicting requirements arising between this specification or any specifications, publications, or draw- ings Usted herein shall be referred i
17、n wxtting to the procuring agency or appointed agent for interpretation, clarification, and resolution (or correction). 3.3 Performance requirements and product characteristics. The record- ing panel shall meet the following performance requirements and product characteristics : 3.3.1 The recording
18、panel shall operate with an input power supply of li5 volts ac plus or minus 3 percent, 400 cps single phase. 3.3.2 All pin, plug, and component numbers given in Drawing 2436236. ified in Table I, given in 4.4.4.2. 3.3.3 InterconnectSons between pins of P7O 3.3.4 With a load of 15 ohms plus or minus
19、 plus or-minus 2 pernt, referred to herein are and SP shall be as spec- 5 percenti connected across pins 5 and 6 of SP and a 400 cpS, ac input of-i volts applied across terminals C and D of P70, the output signal developed across pins 5 and 6 of Sn shall be O.O . . -.- . . 1 . . I .- . . . . I. . 1
20、the same 3.3.7 to 3.3.9 but with of phase MIL-P-238LOA 13 9 9779706 0303820 2 W I- l p0larity as terminal J of P70) shall reduce the output given in zero plus or minus 0.008 volt, peak-to-peak. With il5 volts 400 cps, single phase ac connected as in 3.3.8j the ac input signal to terminals IC and J o
21、f P7O i80 degrees out with that in 3.3.7, the output shall be B.O35 volt plus or minus SO percent, peak-to-peak. . 3.3.10 With a resistive load of 15 ohms plus or minus 5 percent con- nected across pins i5 and 16 of S71, and a 400 cps, ac input of ii5 volts applied across terminals M and N of PTO, a
22、 voltage shall be developed across pins i5 and 16 of S71 which may be adjusted over the range of 0.05 volt to 0.100 voit, peak-to-peak, by potentiometer R. 3.3.U With a resistive load of i5 ohms plus or minus 5 percent con- nected across pins 23 and 24 of Sn and a 400 cps, ac input of 3 volts applie
23、d across terminals U and V of PTO, the output developed across pins 23 and 24 of Sp shall be 0.02 volt plus or minus 20 percent, peak-to-peak. 3.3.2 With the connections as specified in 3.3.11, application of 115 volts, 400 cps, ac across terminals CC and DD of P7O (with terminal CC of P7O having th
24、e same polarity as terminal V of PTO), the output given in 3.3.11 shall be reduced to zero plus or minus 0.008 volt, peak- t o- peak. 3.3.13 With li5 volts, 400 cps, single phase ac connected as in 3.3.l2, but with the ac input signal to terminals U and V of P7O i80 degrees out of phase with that in
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILP23810A1967PANELCOMPONENTRECORDINGFORTORPEDOEXERCISESECTIONMARK64MOD2MARK64MOD2 鱼雷 实验 部分 仪表 面板

链接地址:http://www.mydoc123.com/p-980678.html