1、RIL-P-2383OA L3 Ob 0303836 O _ MIL-P-23810A( OS) i November 1967 Superseding MIL-P- 23810( wep ) PAXEL, COMPoNErlT, mcoRDrNG (For Torpedo Ekercise Section Mark 64 Wd 2) This specification has been approved by the Naval. Ordnance Systems Cornand, Department of the Navy 1. SCOPE 1.1 Scope. This specif
2、ication describes the requirements for the procv- ment, inspection, and test of a recording panel, ED 613310. 2. ApPLICAJ3rn DOoMENTS 2.1 The following documents of the issue in effect on the date of invita- tion for bids or request for proposal form a park of this specification to the extent specif
3、led herein. SPECIFIC ATIONS MXLITrnY 1-0-23560/4 Oscillograph STANDARDS MILTJX?lY m-m-10s Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage MI3-STD-129 DRAWINGS NAVAL ORDNANCE SYSCEMS CONMAFD rn 162756 Shipping (packing) Condition rn 613310 Record5ng Compon
4、ent Panel Assembled Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-2381OA 13 7777706 0303838 4 % MIL-P- 238ioA(0S) . . . 1-0-23560/4, which recor
5、ds the information for later study of the tor- pedos behavior during a run. power supply which furnishes power to all the signal source points that are dc energized. The recording panel also contains a dc 3.2 General requirements 3.2.1 Contractor-furnished data. Data required by this specification o
6、r by applicable documents referenced in Section 2 need not be furnished unless specified in the contract or order (see 6.2). 3.2.2 Preproduction samples. Unless otherwise specified in the con- . tract or order, preproduction samples of the recording panel shall be manufactured using the methods and
7、procedures proposed for the produc- tion lot. and are for the purpose of determining that the production item meets the requirements of this specification and the design. Provisions of samples shall be in accordance with 4.2.1. These samples will be tested as specified in Section 4 herein, 3.2.3 Mat
8、erials. Unless otherwise specified in the contract, requi- sition, or order, all materials and purchased parts entering into the final assembly of the recording panel shall conforpi strictly to the de- tailed requirements indicated on the drawings and specifications listed in LD 613310. . . . 3.2.4
9、Finishes, coatings, construction, and dimensions . Finishes, :.Y: coatings, construction, and dimensions for the recording panel shail be strictly in accordance with the appl5cable draxiilgs, specifications, and publications listed in T;D 613310, 3.2.5 Moisture, fungus, and corrosion. The recording
10、panel shall be rendered moisture, fungus, and corrosion resistant as required by os 6341. 3.2.6 Marking. Marking of assemblies, subassemblies, and parts shall be in accordance with the applicable drawings listed in LD 613310. 3.2.7 Interchangeability. Component parts of the assembled units (unless o
11、therwise specified on the applicable drawings ) fabricated in strict accordance with their applicable drswings shall be interchange- able and shall assemble with mating components of the unit without selection or fitting. a Wt, selection or fitting is required, then changes in dimensions me necessar
12、y and revision and correction of the applicable drawings is required. See 3.2.10. If, during assembly of the fabricated parts of 3.2.8 Gages. The contractor shall provide himself with whatever -=l-q 3 . -. t.I:. I . - “ A I I . , . i. . i- i -.-. - - L -. e d . i . -.- -. - -. _- . _ . . . -. -I ; .
13、 C. L . .:.:.-:. . 1 . - . ,.-_-I . - ., .- * ,. .- .-. L . i , . . l. Y_. - ,._-.- - re.- -. I -.-* . -. . _ .- -.-L . I.- . -.* . -_ -. . . w - .-._.- *“ . !, 1 . .- . -._. .- . ,-_ -.-.-.-. . . - . _-.- -.-._ . “ I .-. . . -,. . . . - . . . . . . . . , . Provided by IHSNot for ResaleNo reproducti
14、on or networking permitted without license from IHS-,-,- flIL-P-23810A 33 m 77777Ob 0303837 b pertinent Navy Final Inspection Gages for guidance in the design of the contractors inspection gages. However, such procedure shall not serve to relieve the contractor of is responsibility in the design and
15、 man- ufacture of such gages as may be reqdred in the satisfactory fulfill- ment of the contract requirements, but is intended-to facilitate ac- ceptance of all components and assemblies by Navy Final Inspection Gages. 3.2.9 Threads. Unless otherwise specified, all threads shall be in accordance wit
16、h National Bureau of Standards Handbook 28. fit for threads shall be as specified on the applicable drawings. The class or 3.2.10 Conflicting requirements . Conflicting requirements arising between this specification or any specifications, publications, or draw- ings Usted herein shall be referred i
17、n wxtting to the procuring agency or appointed agent for interpretation, clarification, and resolution (or correction). 3.3 Performance requirements and product characteristics. The record- ing panel shall meet the following performance requirements and product characteristics : 3.3.1 The recording
18、panel shall operate with an input power supply of li5 volts ac plus or minus 3 percent, 400 cps single phase. 3.3.2 All pin, plug, and component numbers given in Drawing 2436236. ified in Table I, given in 4.4.4.2. 3.3.3 InterconnectSons between pins of P7O 3.3.4 With a load of 15 ohms plus or minus
19、 plus or-minus 2 pernt, referred to herein are and SP shall be as spec- 5 percenti connected across pins 5 and 6 of SP and a 400 cpS, ac input of-i volts applied across terminals C and D of P70, the output signal developed across pins 5 and 6 of Sn shall be O.O . . -.- . . 1 . . I .- . . . . I. . 1
20、the same 3.3.7 to 3.3.9 but with of phase MIL-P-238LOA 13 9 9779706 0303820 2 W I- l p0larity as terminal J of P70) shall reduce the output given in zero plus or minus 0.008 volt, peak-to-peak. With il5 volts 400 cps, single phase ac connected as in 3.3.8j the ac input signal to terminals IC and J o
21、f P7O i80 degrees out with that in 3.3.7, the output shall be B.O35 volt plus or minus SO percent, peak-to-peak. . 3.3.10 With a resistive load of 15 ohms plus or minus 5 percent con- nected across pins i5 and 16 of S71, and a 400 cps, ac input of ii5 volts applied across terminals M and N of PTO, a
22、 voltage shall be developed across pins i5 and 16 of S71 which may be adjusted over the range of 0.05 volt to 0.100 voit, peak-to-peak, by potentiometer R. 3.3.U With a resistive load of i5 ohms plus or minus 5 percent con- nected across pins 23 and 24 of Sn and a 400 cps, ac input of 3 volts applie
23、d across terminals U and V of PTO, the output developed across pins 23 and 24 of Sp shall be 0.02 volt plus or minus 20 percent, peak-to-peak. 3.3.2 With the connections as specified in 3.3.11, application of 115 volts, 400 cps, ac across terminals CC and DD of P7O (with terminal CC of P7O having th
24、e same polarity as terminal V of PTO), the output given in 3.3.11 shall be reduced to zero plus or minus 0.008 volt, peak- t o- peak. 3.3.13 With li5 volts, 400 cps, single phase ac connected as in 3.3.l2, but with the ac input signal to terminals U and V of P7O i80 degrees out of phase with that in
25、 3.3.11, the output shdlbe 0.035 volt plus or minus 20 percent, peak-twpeak. 3.3.14 With a resistive load of 150 ohms plus or minus 5 percent con- nected across terminals E33 and FF of 70 and a il5 volt, 400 cps, ac input applied across terminals CC and DD of P7O, the output developed across termina
26、ls EF, and FF of P7O shall be 4.7 plus or minus 0.5 volts dc, terminal EX being negative. 3.3.15 The peak-to-peak ac ripple component of the dc output voltage specified 5.n 3.3.14 shall not exceed 2 percent of the measured dc voltage. 3.3.16 With the 150 ohm load of 3.3.14 connected across terminals
27、 EE and FF of P70, the dc voltage across terminals EF, and BB of P70 and across terminals FF and BB of P7O shall be half of that voltage measured in 3.3.14, plus or minus 1.0 volt. 3.3.17 With an open circuited phone plug inserted in phone jack J1, there shall be an open circuit between terminal BB
28、of P7O and pin 32 of Sn. The closed circdts from terminal BB of P70 to pins 1, 8, E, 14, 20, and 22 of S7l (as given in Table I) shall not be affected. 50 hours when tested as specified in 4.5.3. 3.3.18 The recording component panel shall have an operating life of . -e-= -. 5 “ . - . _ - . . . .- .
29、. - . . - . i . . . . . . . . . . . . . . . . ? 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 MIL-P-23B1OA 13 9999906 O303821 Y = MIL-P-2381OA( OS) % 3.3.19 With connections as in 3.3.14, a voltmeter connected between pin FF of P70 and pin 3 of
30、 S71, shall indicahe a voltage which may be varied, by adjustment of R75, from O to 4.7 plus or minus 0.5 volts, less the voltage drop through 51,000 ohms due to meter current. 3.4 Environmental requirements 3.4.1 Vibration. The recording ed as specified in 4.5.1, shall be tions for a period of 3 ho
31、urs at a double anplitude (peak-to-peak) of panel, less pack and packaging and mount- capable of withstending vertical vibra- frequency of 60 cycles per second and a 0.016 plus or minus 0.002 inch. There- after the panel shall show no damage and shall meet the performance re- quirements and product
32、chasacteristics of this specification. 3.4.2 Temperature and humidity. The recording panel, less pack and packaging, shali be capable of withstanding a temperature of plus i60 degrees F, plus or minus 5 degrees F, 90 t 95 percent re1ati;e humidity, for a period of 72 hours, in accordance with test p
33、rocedures specified in 4.5.2. Thereafter the panel shall show no corrosion or darnage and shdl meet the performance requirements and product characteristics of this spec- if ication. 3.4.3 Storage life. When Level A preservation, packaging, and packing, as defined in 6.2, is specified, the recording
34、 panel shdl show no damage and shailmeet all the performance requirements and product chasacteris- +ics of this specification after being stored for a period of five years, in the packaging and packing specified, under tenperature and humidity conditions 3.4.3.1 53 degrees 3.4.3.2 as. follows: Tempe
35、rature: c to pius 71 degrees c). Minus 65 degrees F to plus 160 degrees F (minus Humidity: Up to 90 to 95 percent relative. 3.5 Cleanup. Prior to and after final assembly, all pats, components, and the assembly shall be thoroughly cleaned of loose, spattered, or ex- cess solder, metal chips, and oth
36、er foreign matter. and rosin flash shall be removed. AU. burrs, sharp edges, 3.6 Workmanship. The recording panel, including al1 parts and access- ories, shall be constructed and finished in a manner to ensure compliance with all the requirements of this specification. shall be paid to neatness and
37、thoroughness of soldering, wiring, marking of parts and assemblies, paLnting, machine screw assembhge, welding, braz- ing, and freedom of parts from burrs and sharp edges. workmanship exhibited in any approved preproduction sample, subject to any qualification stated in the Governments notice of app
38、roval, shall be de- terminative of the requirements of the contract relative to workmanship insof a as not specif iclly covered by agplicable specifications . Particular attention The standards of -. _ , - - ? i; -. . - . . . .-. - .- . -1 . . . . 1 . . . - . _.- -. I_- - -.* . _.-_- - . -_. - . -4
39、. .- . _.-_ . . . . . . . “ . . . . -7 . L . . . . t:.: t :=.: c . . i . . L._ . _-_ . - . I - . .- -. . -.-.- -_.-I e- . .- . -. I_. -.- . . . - . . . I .-. *- .- . 1 .,.I . .- -.- . -.-. . ._ . -. . - . . -_ . . p: : : :;:xz:; Provided by IHSNot for ResaleNo reproduction or networking permitted wi
40、thout license from IHS-,-,-1-23810A( OS) 4. QUALtITY ASSUFP;NCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the perform- ance of dl inspection requirements as specified herein. Except as otherwise specifi
41、ed, the supplier may utilize his m facilities or any comercial laboratory acceptable to the Government. The Government re- serves the right to perform any of the inspections set forth in the specification where such inspections are deemed necesszuy to ensure that supplies and services conform to pre
42、scribed requirements. 4.1.1 Classification of characteristics . The characteristics verified by the tests and examinations herein are classified as Critical, Major, or Mnor, in accordance trith WR-43. Tests and examinations that verify critical characteristics are identified by the symbol (C) and th
43、ose that verify major characteristics are identified by the symbol (M). number following the classification symbol indicates the serial number of the test or examination. with a classification code are classified minor. The Tests and examinations that are not annotated 4.2 Sampling 4 -2.1 Preproduct
44、ion sample. Unless otherwise specified for each con- tract or order, a representative sample of five recording panels shall be submitted to the Government inspector, preserved, packaged, and packed as specified in the contract or order, for production tests at an activity designated in the contract
45、or by the Naval Ordnance Systems Comand. Further production of the recording panels by the contractor prior to approval of the contracting activity of preprodvction samples shall be at the contractors risk. Preproduction samples accepted will be applied as part of the quantity specified in the contr
46、act or order. 4.2.2 Lot size. As applied to Government inspection of units of pro- duction, the term lot“ shall mean “inspection lot,“ that is, a collec- tion of units of product submitted by a supplier for Government inspec- tion. inspection lots will be determined by the Government inspector and m
47、ay differ from the quantity designated in the contract or order in a lot for production, shipment, or other purpose. Unless otherwise specified, the number of units of product in 4.2.3 Periodic production samples Step 1. Upon initiation of production the Government inspector shall randomly select on
48、e unit from each group of five units for submission to a Naval Ordnance Systems Comand activity. Step 2. Upon satisfactory compliance of each unit from three consec- utively produced groups, select a sample in accordance with MIL-STD-105, Inspection %vel L-4 (acceptance number zero), based on the remainder of the contract. i 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-P-2381OA 13 m 9999906 0303823 MIL-P- 238ioA( OS) Step 3. When a def
