NAVY MIL-L-82531-1968 LEAD EXPLOSIVE MK 5 MOD 0《MK 5 MOD 0铅爆炸物》.pdf

《NAVY MIL-L-82531-1968 LEAD EXPLOSIVE MK 5 MOD 0《MK 5 MOD 0铅爆炸物》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-L-82531-1968 LEAD EXPLOSIVE MK 5 MOD 0《MK 5 MOD 0铅爆炸物》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-L-BZ53L 13 777770b 03bL7b b s- 37/19 NTS XS 457 Rev. A 31 January I96G MILITARY SPECIFICATION FOR LEAD, EXPLOSIVE, MK 5 MOD O This specification has been approved by the Naval Ordnance Systems Command, Department of the Navy 1, SCOPE 1 1 This specification establishes the requirements of one fyp

2、e of Explo- 2, APPLICABLE DOCUMENTS sive Lead Mk 5 Mod O. (See 6.1 for intended use and description.) 2.1 The following documents, of the issue in effect on the date of invitation for bids, form a part of this specification ta the extent specified herein, except as noted. SPECIFICATION FEDERAL QQ-A-

3、225 15 Aluminum and Aluminum Alloy Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished; General Specification ?or STANDARDS MILITARY MILSTD-105D Sampling Procedures and Tables for Inspectionby Attributes Marking for Shipment and Storage MIL-STD-129 Provided by IHSNot for ResaleNo repr

4、oduction or networking permitted without license from IHS-,-,-MIL-L-82531 13 = 7779906 03b1768 . _- MIL-L-82531 (OS) DRAWINGS BUREAU OF NAVAL WEAPONS LD 251339 Lead, Explosive, Mk 5 Mod O, and all drawings listed thereon LD 268000 LD 275959 Primer, Electric, Mk 137 Mod O, and all drawings listed the

5、reon Detonator Container Mk 6 Mod O (Inner), and all drawings listed thereon LD 275960 Det-onator Container Mk 8 Mod O (uter), and all drawings listed thereon (Copies of specifi.cations, standards, drawings, and publications requested by contractors in comaction with specific procurement functions s

6、hould be ob- tained from the procoiring activity or as directed by the contracting officer .) 2.2 Other publications interstate Commerce Commission 49 CFR Part 71 to 78 Interstate Commerce Commission Rules and Regulations for the Transportation of Explosives and other Dangerous Articles (The Lnterst

7、at,e Com ce Commission regulations are now a part of the Code of Federal Regulatio Documents, Government .Printing Office, Washington D. C. 20402. Orders for the above publication should cite “the latest issue and supplements thereto“. ) d are available from the Superintendent of 3. REQUIREMENTS 3.1

8、 General requirements. Unless otherwise specified in the contract or order, all materials and treatments of materials and parts used in the manufac- ture of the lead shall be in accordance with the requirements specified herein and with the applicable docments listed in BuWeps LD 251339. 3.2 Preprod

9、uction samples. Unless otherwise specified in the contract or order, preproduction samples of the lead shall be manufactured-using the methods and procedures proposed for production. The samples shall be tested as specified in Section 4 herein, and are for the purpose of determining that, prior to s

10、tarting production, the contractors production methods ar *capable of yielding items that comply with the technical requirements of the contract. 3.3 Performance and product characteristics. The lead shall meet the following performance and product characteristics. Provided by IHSNot for ResaleNo re

11、production or networking permitted without license from IHS-,-,-MIL-L-82531: (OS) 3.3.1 Lead output and func,ming. The lead shall function and produce an indentation more than O. 010 inch deep in a steel test block when subjected to the output of Detonator Mk 59 Mod O. 3.4 Workmanship. The workmansh

12、ip and finish shall be of sufficiently high grade to assure satisfactory operation consistent with the requirements of this specification. All parts used in the assembly shall be thoroughly clean and free of exoess materials, chips, and loose or splattered foreign materials. The standards of workman

13、ship exhibited in any approved preproduction sample, sub- ject to any qualification stated in the Governments notice of approval, shall be determinative of the requirements of the contract relative to workmanship inso- far as not specifically covered by applicable specifications. 4. QUALITY ASSURANC

14、E PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con- tract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commer

15、cial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed nec- essary to assure that supplies and services conform to prescribed requirements. as follows: 4.2 Classification of in

16、spection. Inspection of the lead shall be classified a. Preproduction inspection (See 4.5.) b, Quality conformance inspection (See 4.6. ) 4.3 Sampling. (See 6.2.1. ) 4.3.1 Lot size. The term “lotff shall mean “inspection lot“, that is a collection of product submitted by a supplier for inspection. U

17、nless otherwise specified in the contract or order, the number of product in each lot shall be ten thousand (10,000). 4.3.2 Premoduction samole, A preproduction sample of fifty (50) leads, manufactured in accordance with 3.2, shall be subjected to the quality confor- mance inspections detailed in 4.

18、6. Acceptance of the preproduction sample shall be judged in accordance with MIL-STD-l05D, inspection Level II, with an AQL of 1. O. A dud (see 6.3.1) shall be cause for rejection of the preproduction sample. Further production of the primers by the supplier, prior to approval of the preproduction s

19、ample, shall be at the suppliers risk. /- 3- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking

20、permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-Z533 33 m 7779706 0363773 3 _ Table I, Quaiity Conformance Tests and Examinations and AQL Sampling Test Plan AQL Test Paragraph Lead Output and Functioning *

21、 1.0 4,6.1,1 Visual Examination * * 4.6.1.2 Packaging, Packing, and Marking * * 4.7 *MIL-STD-l05D Inspection Level II. The AQL of 1, O applies to the indentation of the test block. In addition, a dud lead (see 6.3.1) shall be cause for rejec- tion of the lot. *One-hundred percent inspection; defect

22、is cause for rejection of individual unit, test equipment and arrangement specified in 4.4. la and shown in Figure 1 and 2. The lead shall be detonated by Detonator Mk 59 Mod O, which in turn shall be initiated by either Electric Primer Mk 137 or other suitable initiator with equal output. The desig

23、n of the test holder shown in Figure 1 may be modified to ac- commodate a suitable primer used for reliable initiation of the detonator. 4.6.1.1 Lead output and functioning. This test shall be conducted using the 4.6.1.1.1 Measurement procedure. The maximum depth of indentation produced in each test

24、 block shall be measured and recorded to the nearest O. O01 inch, using the dial indicator specified in 4.4. lb. The dial indicator shall be mounted over a horizontal surface plate so that the indicator stem is perpendicular to the surface plate, as shown in Figure 2. The test block shall be placed,

25、 in- dented side up, in a holder so that the bottom face of the test block is approxi- mately parallel to the surface plate. The indicator tip shall be lowered to the bottom of the indentation, and the indicator dial set to zero, The test block holder shall then be moved so that the indicator tip co

26、ntacts the surface of the testblock approximately 1/8 inch from the periphery of the test block. The indicator reading shall be recorded to the nearest O. O01 inch, Four readings shall be taken at approximately equidistant points near the periphery of the in- dentation. The arithmetic average of the

27、 four readings shall be taken as the average depth of indentation for each test block. The average depth of indenta- tion shall be not less than O. O10 inch. 4.6.1.2 Visual examination, Visual examination shall be made on each Nonconfor- lead submitted for delivery to the procuring agency. The lead

28、shall be examined for conformance to the requirements of good workmanship in 3.4 mance is cause for rejection of individual unit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-2531 13 7777906 0361774 3 U _. - MIL-L-82531 (OS) 4.7 Packaging, p

29、acking, and marking. The lead shall be examined for conformance to the prescribed packaging, packing, and marking requirements of Section 5. 5. PREPARATION FOR DELIVERY 5.1 Packaging. One thousand (1000) leads shall be packaged in accordance with instructions contained in the applicable documents li

30、sted in LD 275959. 5.2 Packing, Four thousand (4000) leads, packaged as specified in 5.1, shall be packed in accordance with instructions contained in the applicable docu- ments listed in LD 275960. 5.3 Marking. In addition to any special marking required by the contract or order, unit packages, int

31、ermediate packages, and shipping containers shall be marked in accordance with the requirements of MIL-STD-129, 49 CFR Part 71 to 78, and LD 275960. 5.4 Lead data cards. Five (5) cards, 3 inches by 5 inches, made from commercial white cardboard, printed as shown in Figure 3, shall be filled out for

32、eachlot of leads, and shall be distributed as follows: a. Two cards shall accompany the shipping ticket. b. Two cards shall be forwarded to the procuring activity. c. One card shall be placed in each packing container. 6. NOTES 6.1 Intended use and description. -6.1.1 Intended use. The lead is inten

33、ded for use in the motor separation and airframe separation explosive blocks of a rocket-propelled missile. 6.1.2 Description, The lead is designed to be reliably initiated by Deton- ator Mk 59 Mod O and to yield a highly brisant output. The lead is approximately O. 161 inch in diameter by O. 380 in

34、ch long, and contains approximately 120 milli- grams of RDX primary explosive. 6.2 Ordering data. Procurement documents should specify the following: a. Title, number, and date of this specification b. Required level of packaging c. Required level of packing d. Provision for supplying data cards as

35、specified in 5.3.2 e. Any exceptions to this specification Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-82531 13 m 7779706 0361775 5 m MIL-L-82531, (OS) 1 LEAD, EXPLOSIVE, MK 5 MOD O DATA CARD Spec Loaded by Date: Mo. Yr. Contract No. No. in

36、 Box Prod. Lot SiZ Lot Type: ( ) Regular ( ) Mixed ( ) Special - LOTOR DATE MATERIAL MANUFACTURER BATCH NO. MO. YR i Lead Cup es RDX Charge Remarks Figure 3. Lead Data Card Format Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-82531 13 7777706

37、 03b177b 7 MiL-L42531 (OS) 6.2.1 Additional samples, Additional samples required because of failure of any sample(s) to pass the prescribed inspections shall be provided and inspec- ted at the expense of the supplier. 6.3 Definitions. For the purpose of this specification the following defini- tion

38、has been established. 6.3.1 Dud. Any lead that fails to explode when subjected to the output of an adjacent Detonator Mk 59 Mod O, shall be termed a dud. Failure of any lead to explode due to faulty detonator functioning or test equipment shall not be con- strued as a dud. 6.4 Preparation for delive

39、ry criteria, Criteria for use of the proper level of packaging, packing, and marking shall be as specified in Section 5. 6.5 Safety precautions. 6.5.1 Special handling instructions. 6.5.1.1 Extreme care and precautions shall be exercised at all times in the handling and loading of the RDX material.

40、6.5.1.2 No more than 2 grams of RDX shall be present at each loading station and only when an operator is present. 6.5.2 General safety precautions. The loading assembly, and handling of explosivs, ammunition, ammunition components, fuzes, detonators, primers, tracers, boosters, pyrotechnics, etc.,

41、and subassemblies thereof , involve hazar- dous operations, and therefore require suitable explosives safety precautions Use of this specification shall not be construed as to relieve the contractor or manufacturer of responsibility for the safety of his operations. The following paragraphs list the

42、 minimum provisions that a contractor or manufacturer (loader) of these items should observe in order to fulfill his responsibility for safety. At Naval Ordnance Systems Command and other 3overnment plants, these provisions are mandatory. Such other warnings and precautions pertinent to the operatio

43、nal effectiveness or safety during use or loading of the specified item, are included in the detail provisions of the specification. 6.5.2.1 All loading operations should be conducted in a neat and orderly manner. 6.5.2.2 Safe equipment and methods should be utilized for transporting and handling ex

44、plosives and loaded parts. Where required, remote control barricaded handling equipment shall be used for explosive operations, such as mixing, pouring,. weighing, charging, sifting, drying, pressing, casting, and crimping. Provided by IHSNot for ResaleNo reproduction or networking permitted without

45、 license from IHS-,-,-MIL-L-82531 (OS) 6.5.2.3 Personnel handling detonators, primers, delay elements, leadins, boosters, and related parta that affect functioning, should, insofar as practicable, avoid using bare fingers or improper equipment to prevent damage, corrosion, or deterioration from pers

46、piration or other contaminating deposits. 6.5.2.4 The exposure of explosive materials and related parts should be so controlled as to minimize the absorption of moisture from the atmosphere or other sources during loading and handling operations. 6.5.2.5 All explosives and completely or partially lo

47、aded items should be stored in suitable storage magazines located in accordance with the American Table of Distances (ATD) or other applicable safety standards; and, while in process, kept in safety lockers and chests if in loading rooms, or in adequate ready or service magazines located in accordan

48、ce with intra-plant distances when outside of loading rooms. For Navy explosive loading plants,. the pro- visions of the Armed Services Explosives Safety Board covering quantity-distance relations for explosives, shall apply. 6.5.2.6 Proper care should be exercised at all times to protect personnel

49、from accidents, fires, or explosions, and to limit damage to equipment and loading areas. in this connection, the following precautionary measures should be observed. 6.5.2.6. I Employ properly proportioned and properly located protective barricades, screens, or shields at all required points, 6.5.2.6.2 Keep only minimum limited quantities of explosiv