NAVY MIL-I-85671-1987 INDICATOR FREQUENCY CHANNEL ID-2121A ARC ID-2229A ARC AND ID-2303 ARC《ID-2121A ARC ID-2229A ARC 及 ID-2303 ARC型频道指示器》.pdf

《NAVY MIL-I-85671-1987 INDICATOR FREQUENCY CHANNEL ID-2121A ARC ID-2229A ARC AND ID-2303 ARC《ID-2121A ARC ID-2229A ARC 及 ID-2303 ARC型频道指示器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-I-85671-1987 INDICATOR FREQUENCY CHANNEL ID-2121A ARC ID-2229A ARC AND ID-2303 ARC《ID-2121A ARC ID-2229A ARC 及 ID-2303 ARC型频道指示器》.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-1-85671 5B = 7779906 0376402 5 MIL-I-85671( AS 1 7 JULY 1987 MIL I TARY SPECIFICATION INDICATOR, FREQUENCY CHANNEL ID-2121A/ARCI ID-2229A/ARCI and ID-Z303/ARC This specification is approved for use within the Naval Air Systems Command, Department of the Navy and is available for use by all Depar

2、tments and Agencies of the Department of Defense. 1. SCOPE 1.1 ScopeL This specification ectabl i shes the performance, design, and test requi rements for the ID-ZlZlA/ARC, ID-2229A/ARC and ID-2303/ARC Indicators, Frequency Channel hereinafter referred to as the indicator. The indicators covered in

3、this specification are used with the receiver- transmitters of the ARC-182 family. Three types of indicators are covered by this 1.2 Classification, specification. colors of the panel lighting. fol lows: The principle difference between the three indicators is the The indicators and respective light

4、ing are as a. ID-ZlZlA/ARC Red b. ID-Z229A/ARC White C. ID-Z303/ARC B1 ue-White Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commanding Officer, Naval Ai r Engineering Center, Systems Enginee

5、ring and Standardiza- tion Department (SESD) Code 53, Lakehurst, NJ 08733-5100 by using the sel f-addressed Standardization Docunent Improvement or by letter. DISTRIBUTION STATEMENT A: Approved for public release; distribution is un1 imited. AMSC N/A , h THIS DOCUMENT CONTAINS d-0 PAGES. FSC 5821 Pr

6、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-85b71 58 W 7777906 0176403 7 2. APPLICABLE DOCUMENTS 2.1 Government documents, The following specifications and 2.1.1 Spec1 flsation and standards standards form a part of this specification to the

7、extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the sol icitation. SPEC1 FI CAT IONS F_ederal QQ-P-4 16 M11Starv MIL-B-50

8、87 MIL-W-5088 MIL-E-5400 M IL -T-5 4 2 2 MIL-C-678 1 MIL -P-7 78 8 MI L-E-1755 5 MIL-T-18303 MIL-N-183 07 M I L-C-25 05 O MIL-M-385 10 Plating, Cadmium (Electrodeposited) Bonding, Electrical, and Lightning Protection, f o r Ae ros pa ce Systems Wiring; Aircraft, Selection and Installation of Electro

9、nic Equipment, Ai rcraft, General Specification for Testing, Envi ronmental 8 Aircraft Electronic Equipment Control Panel ; Ai rcraft Equipment, Rack or Consol e Mounted Panel Information, Integrally 11 iuminated Electronic and Electrical Equipment, Accessories, and Repair Parts, Packaging and Packi

10、ng of Test Procedures; Preproduction, Acceptance and Life for Aircraft Electronic Equipment, Format for Nomencl ature and Identi f ication for 1 ectronic, Aeronautical, and Aeronautical Support Equipment Incl uding Ground Support Equipment Colors, Aeronautic Lights and Lighting Equi pment, General R

11、equi rements for Microci rcuits, General Specification for 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-85b71 58 7777906 017b40Y 7 m M IL -C-3 8 99 9 MIL-H-46855 MIL-P-55 110 MIL-C-85666 STANDARDS Federal FED-STD-5 95 t!KuhJx MIL-STD-129 M

12、IL-STD-275 MIL-STD-415 M IL-STD-454 MIL-STD-461 MIL-STD-462 with Notice 2 MIL-STD-47 1 MIL-STD-704 MIL -STD-781 MIL-STD-785 Connectors, Electrical , Circular, Miniature, High Density, Quick Disconnect, Envi ronmental Resistant, Removable Crimp Contacts; General Speci f icati on for Human Engineering

13、 Requirements for Mil itary Systems Equipment and Facilities Printed Wiring Boards Control , Radio Set C-10319A/ARCI C-l0776A/ARC, and C-1113 1/ARC Federal Standard Col ors Marking for Shipment and Storage Printed Wiring for Electronic Equipment Test Provisions for Electronic Systems and Associated

14、Equipment, Design Criteria for Electronic Equipments, General Requi rements for Electromagnetic Interference Characteristics Requi rements for Equipment El ectromagnetic Interference characteristics, Measurement of Maintainability Demonstration Electric Power, Aircraft, Characteristics and Utilizati

15、on of Re1 iabil ity Tests; Exponential Distribution Re1 i abi 1 i ty Program for Systems and Equipment Development and Production 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-8Cb72 58 W 4794706 OL7hY05 O W MIL- 1-8567 1 ( AS 1 MIL-STD-8 10

16、 Envi ronmental Test Methods MIL-STD-883 Test Methods and Procedures for Microelectronics MIL-STD-965 Parts Control Program M IL-STD-1472 Human Engineering Design Criteria for Military System Equipment and Facilities MIL-STD-1562 Lists of Standard Microci rcuits MIL-STD-2074 Failure Classification f

17、or Reliability Testing M IL -S TD-2 07 6 Unit Under Test Compatibility with Automatic Test Equipment, General Requi rementc for MIL-STD-2084 Maintainability of Avionics and Electronic Systems and Equipment, General Requi rments for 2,l.Z Other Goverwt doca . The following other Government documents

18、form a part of this specification to the extent specified herein. Unless otherwise specified? the issues shall be those in effect on the date of the sol icitation. DOCUMENTS 4 WS-65 3 6 Process Sped f icati on Procedures and Requirements for Preparations and Sol dering of Electrical Connections NAVM

19、AT P-4855 1 Navy Power Supply Re1 i abi 1 i ty NAVMAT P-9492 Navy Manufacturing Screening Program (Copies of specifications, standards and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as direc

20、ted by the contracting activity. 1 2.2 Order of precedence, In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards)? the text of this specification shall take precedence, Not

21、hing in this specification, however, shall supercede applicable laws and regulations unless a specific exemption has been obtained. W O 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-I-8567L 58 W 7779706 OL761tO6 2 3. REQUIREMENTS a The ID-21

22、21A/ARCI ID-2229A/ARC and ID-2303/ARC 3.1 Item description. Frequency Channel Indicators shall be self-contained units for cockpit mounting. host receiver-transmitter and radio set control. The indicators shall contain circuits necessary to operate with a 3.2 Fi rst article, When specified in the co

23、ntract or purchase order (see 6.2.11, a sample shall be subjected to first article inspection (see 4.4 and 6.3). * 3.3 Parts. In the selection of parts, the prime Considerations are fulfil lment of performance requirements, logistics supportability and reliability assurance in a cost effective desig

24、n. The following shall govern in parts selection. a. Subassemblies shall be designed and fabricated to be repairable. Maximum econanic standardization of parts and materials chal 1 be exercised. Parts selection shall be made in the following order of precedence: (1) Mil itary Standard parts shall be

25、 selected in accordance with MIL-STD-454, Requi rement 22. (2) Nonstandard parts previously qual if ied for other programs. (3 1 Nonstandard parts. b. Nonstandard parts and nonestablished re1 iabi ity military standard parts shall be screened to the requirements of the most similiar military standar

26、d or standard nonestabl ished re1 iabil ity pa t. Integrated circuits and hybrids shall use MIL-STD-883, Method 5004, Class B, as a basis for tailored screens. 3.3.1 Cbmponent rescr eeni ng. The contractor shall conduct 100 percent incoming inspection of all active components used in production equi

27、pment and spares. Functional and parametric checks of active components shall be performed at the components rated temperature extremes and at ambient. Components which are not compliant with their specification shall not be used in the ARC. 3.3.2 Parts deratina and application, All parts used shall

28、 be applied well within their ratings. The derating shall encompass the appropriate and meaningful appl ication conditions such as voltage, current, power, temperature, mechanical, and duty cycle. Electronic and electromechanical parts shall conform to Table I electronic parts derating for worst cas

29、e electrical and environmental stress unless formal written approval is received from the procuring activity prior to incorporation into the design. Part level stress analysis shall be used to verify that all parameter stresses are within the derated values at worst case circuit and environmental co

30、nditions. The following limitations on parts usage shall apply: a 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Part Type P arameter Cap aci tor Appl ied Vol tage for Tantal um) (Ripple Vol tage Res i stors Power Vol tage Current Vol tage Diodes

31、Power junction Temperature Trans i stors Power Vol tage Junction Temperature Integrated Ci rcuits Digital Fan-Out, fan-In L i near Power Junction Temperature junction Temperature Tran sformers, Parts shall be used at a 1 Maximum Al lowable Appl ication Stress 50% of rating 1/ 50% of rating 70% of ra

32、ting 50% of rating 75% of rating 60% of rating 2/ 55% of rating 6% of rating 2/ 805% of rating 2/ 75% of rating 2/ winding temperature of 1/ For coid tantalum and all electrolytic capacitors, the maximum applied voltage shall be not greater than 70 percent of the vendor rated value. Wpplied voltage“

33、 is the sum of the applied peak ripple voltage and the appl ied DC voltage. Table Induct ive Devices . I. Electronic parts dera-. at least 30 degrees below rated temperature. addition, the maximum voltage between windings or between a winding and a shield shall be not greater than 60% of rated volta

34、ge for the steady state conditions and 90% of rated voltage with transients. General purpose inductors, audio and power transformers shall be appl led at no more than 70% of rated current. In 2/ Semiconductor devices shall be mounted and operated in such manner to insure worst-case junction temperat

35、ure is not greater than 110 degrees C at 4-71 degrees C ambient temperature. activity approval. Power semiconductor devices, on a very selective basis, may be mounted and operated with worst case junction temperatures not greater than 150 degrees C att71 degrees C ambient temperatures. Any deviation

36、 requires procuring 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-85bl1 58 777790b OL7b408 b a. Prohibited application (1) Non-hermetical ly sealed semiconductors except paver transistors (2) Photo coup1 ers (photo transistors) (3) Hot carr

37、ier (Schottky) rectifiers (4) Microcircuit sockets (5 1 Non-hermetical ly sealed wet tanta1 um capacitors 3.3.3 Parts control proaram. The contractor shall establ ish and maintain a parts control and standardization program in accordance with the requirements of MIL-STD-965, Procedure I and as speci

38、fied herein. The program shall control part standardization and the criteria for the selectionr application, and testing of parts to achieve the reliability required. program equivalent to that specified herein chal 1 be required of subcontractors and suppl iers. As a minimumr a parts 3.3.4 Non - st

39、andard parts approval. The contractor shall obtain procuring activity approval of all non-standard parts used in the equipment. Standard parts are defined in MIL-E-5400. In addition to the MIL-E-5400 requirements for standard partsr microelectronic parts are standard only if: a. The device is listed

40、 in MIL-STD-1562, and b. Sources (at least two) are listed on the Qualified Parts List (Wi-18 and c. d. Quality level llBtl (or better) of MIL-M-38510 is required. The part is procured from one of the qualified sourcesF and O The approval procedure chal 1 be in accordance with MIL-E-5400 and MIL-STD

41、-965, Procedure I. In addition to the requirements of MIL-E-5400, approval of non- standard parts will be based on: a. Suitability for the application b. Conformanee to this specification and to MIL-E-5400 c. Interchangeabil ity d. Screening (burn-in) method 3.3.5 SxnpTes of non - standard parts . S

42、amples o not required unless specified in the contract, Where samples are specified in the contract, the sample sha MIL-E-5400 (see 6.2.1). non-standard parts are non-standard parts 1 be in accordance with Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

43、,-,-MIL-I-5b71 58 99999Ob 017b1107 3 Col or (Short Name) P-l I L -I -85 67 1 (AS 1 Col or per M IL-P-7788 MIL-C-25050 C1 ass 3.3.6 Cabling and connections, BLUE FILTERED WHITE 3,3,6.1 Cables and connecto rs. The indicator shall provide for the use of cables and connectors in accordance with MIL-E-54

44、00. The design of the connectors shall be such that improper assembly, mating or installation is impossi S7a. Non-RF connectors shall meet the requi rements of MIL-C-38999. Al 1 sxtgrnal Connectors chai 1 be scoop-proof , have cadmiuni pl ati ng fi ni sh i n accordance with QQ-P-416 (over a suitable

45、 underplating) to withstand a 500 hour salt test, and provide 360 degrees circumferential grounding techniques for grounding prior to contact engagement. Type 1 (h) 1 -BW 3.3.6.2 Interconnection cab1 ina. The indicator shall be capable of required operation using external wiring in accordance with t

46、he applicable requirements of MIL-W-5088, The external wiring chal 1 be unshielded, except that a miniinu,n numbor of the individual wires may be shielded when demonstratsd as necessary to meet interference control requirements and provide the assembly of the cable to its plugs nay be easily accompl

47、ished, External cables and that portion of the connectors attached to the cables shall not be supplied as part of the indicator. 3.37 Control pan el sL The control panels shall conform to the applicable requi rments of MIL-C-6781. 3,3.7,1 Liahted panels - console mounted eau ipment, The plastic pane

48、ls for all console mounted control panels, indicators, and radio sets shall conform to MIL-P-7788, Class 1-R, 1-W, or 1-BW Type V, with both 5 and 28 volt (ac and dc) lamp systems installed. Separate input power pins shall be provided for the two lighting systems. Color of panel lighting shall be in

49、 accordance with VIL-C-25050, as selected from the options listed in Table II by nomenclature assignment, or by description on purchase orders. Nomenclature ( Rev 1 s ab 1 e 1 IO-Z121A/ARC ID -2229A/A!?C ID -2303 /ARC Table II. Panel lightina opt i ou I 1 IPL RED IPL WHITE P 1 -R 1-w 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-I-8567L 58 9999906 OL764LO