NAVY MIL-C-29512-1988 CHARGER BATTERY PP-7806 BRT-6《PP-7806 BRT-6电池充电器》.pdf

《NAVY MIL-C-29512-1988 CHARGER BATTERY PP-7806 BRT-6《PP-7806 BRT-6电池充电器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-29512-1988 CHARGER BATTERY PP-7806 BRT-6《PP-7806 BRT-6电池充电器》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-27512 54 W 7797706 0157063 2 W $7 ./5 .al MIL-C-29512( EC) 26 January 1988 MIL I TARY SPEC IF I CAT ION CHARGER, BATTERY, PP-7806/BRT-6 This specification is approved for use by the Space and Naval Warfare Systems Command, Department of the Navy, and is available for use by all Departments and

2、 Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the performance, manufacture, and The BC and the Cable Kit are part I test requirements for the Charger, Battery, PP-7806/BRT-6, hereinafter referred to as the BC, and the Interconnecting Cable Assembly, CX-13318/B

3、RT-6, hereinafter referred to as the Cable Kit. of the Buoy Transmitting Set, AN/BRT-6. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following 0 specifications, standards, and handbook form a part of this specification to the extent specified

4、herein. Unless otherwise specified, the issues of these documents shall be those listed in the.issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. comments (recommendations, additions, deletions) and any pertinent data

5、which mw be of use in improving this document should be addressed to: Commander, Space and Naval Warfare Systems Command (SPAWAR 003-1211, Washington, DC 20363-5100, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document, or by

6、letter. AMSC N/A FSC 5820 DISTRIBUTION STATEMENT A. Approved for public release; distribution is un1 imi ted. T 7 THIS DOCUMENT CONTAINS 6d.J PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPEC IF ICATIONS MILITARY MIL -S -90 1 MIL-P-13949 MI

7、L-E-16400G MIL-E-17555 MIL-F-18264 MIL -S-19500 MIL-C-21097 MI L-C- 24643/45 MIL-C-28840 MIL-B-29513 MIL-M-38510 MIL-P-55110 STANDARDS MIL ITARY MIL-STD-105 MIL-STD- 108 MIL-STO-109 MIL-STO-167-1 MIL-C-29512( EC) Shock Tests, H.I. (High-Impact); Shipboard Machinery, Equipment And Systems, Requiremen

8、ts For Plastic Sheet, Laminated, Metal Clad (For Pri nted Wi ring Boards), General Specification For Electronic, Interior Communication And Navigation Equipment, Naval Ship And Shore: General Specification For Electronic And El ectrical Equipment, Accessories, And Provisioned Items ( Repai r Parts)

9、: Packaging Of Finishes: Organic, Weapons System, Application And Control Of Semiconductor Devices, General Specification For Connectors, Electrical , Printed Wiring Board, General Purpose, General Specification For Cable, Electrical, 300 Volts, Type LS2U (Including Variation LS2UA) Connectors, Elec

10、trical , Ci rcul ar Threaded, High Shock, High Density, Shipboard, CI ass O, General Specification For Buoy, Radio Transmitter, T-1455/BRT-6 Microcircuits, General Specification For Printed Wiring Boards, General Specification For Sampling Procedures And Tables For Inspection By Attributes Definitio

11、ns Of And Basic Requirements For Enclosures For Electric And Electronic Equipment Quality Assurance Terms And Definitions Mechanical Vibrations Of Shipboard Equipment (Type I - Environmental And Type II - Internally Excited) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted with

12、out license from IHS-,-,-e HANDBOOK MIL-STD-275 MIL-STO-454 MIL-STD-461 MIL-STD-462 MIL-STD-471 MIL-STD-781 MIL-STD-810 MIL-STD-965 DoD-STD-1399, Section 300 MIL-STD-1472 MIL-STD-1683 DoD-STO-1686 MIL-STD-2164 MS 27505 Printed Wiring For Electronic Equipment Standard General Requirements For El ec t

13、ron i c E qu i pmen t Electromagnetic Emission And Susceptibility Requirements For The Control Of Electromagnetic Interference Electromagnetic Interference Characteristics, Measurement Of Maintainability Verification/ Demonstration/Eval uati on Re1 iabil ity Testing For Engineering Development, Qual

14、ification, And Production Environmental Test Methods And Engi neeri ng Gui del i nes Parts Control Program Interface Standard For Shipboard Systems, Electric Power, Alternating Current (Metric) Human Engineering Design Criteria For Military Systems, Equipment And Facil i ties Connectors And Jacketed

15、 Cab1 e, Electric, Selection Stqdard For - Shipboard Use Electrostatic Discharge Control PFohm, For Protection Of Electrical And Electronic Parts, Assemblies And Equipment (Excluding Electrically Initiated Explosive Devices) (Metric) Environmental Stress Screening Process For Electronic Equipment Co

16、nnector, Receptacle, Electrical Back Panel, Box Mounting Flange, Crimp Type, Bayonet Coupling, Series 1 - MILITARY DoD-HDBK-263 Electrostatic Discharge Control Handbook For Protection Of Electrical And Electronic Parts, Assemblies And Equipment (Excluding Electrically Initiated Explosive Devices) (M

17、etric) 2.1.2 Government drawings and publications. The following Government drawing and publication form a part of this specification to the extent specified herein. effect on the date of the solicitation. Unless otherwise specified, the issues shall be those in 3 Provided by IHSNot for ResaleNo rep

18、roduction or networking permitted without license from IHS-,-,-MIL-C-27522 58 W 7779706 OL570bb 8 W MIL-C=29512( EC) DRAWING NAVAL SEA SYSTEMS COMMAND (NAVSEA) F53711-409-6379608 Remote Indicator And Interconnecting Cab1 es PUBLICATION NAVAL AIR SYSTEMS COMMAND (NAVAIR) AS-4613 Appl ication And Dera

19、ting Requirements For Electronic Components, General Specification For (Copies of specifications, standards, handbooks, drawings, and publications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contract

20、ing officer. 1 this specification and the references cited herein (except for associated detail specifications, specification sheets, or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations, unles

21、s a specific exemption has been obtained, 2.2 Order of precedence. In the event of a conflict between the text of 3. REQUIREMENTS 3.1 General. The BC and Cable Kit shall be in accordance with MIL-E-16400Ga to the extent specified herein. 3.1.1 First article. When specified in the contract or purchas

22、e order, a sample shall be subjected to first article inspection (see 4.3 and 6.3). 3.1.2 BC description. The BC is part of the Buoy Transmitting Set, AN/BRT-6 (see FIGURE 1). The BC provides a charging station for up to six Radio Transmitter Buoys, T-1455/BRT-6 (buoys) specified in MIL-B-29513. The

23、 BC provides a high and low charging voltage to the buoys, -displays the accummulated power-on elapsed time and monitors the buoy charge current and vol tage. 3.1.3 Cable Kit description. The Cable Kit consists of one cable assembly which provides the electrical interconnection between the BC and si

24、x buoys. 3.2 Performance. BC performance shall be as specified in 3.2.1 through 3.2.5. 4 o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-29512 58 9999906 0257067 T - BUOY INTERFACE I. RADIO TRANSMITTER BUOY T-1455/BRT-6 f I , fl RADIO TRANSMI

25、TTER BUOY T-14 5 S/B RT-6 I II I I I I RADIO TRANSMITTER BUOY BAUERY T-14551BRT-6 CHARGER (BC) n RADIO TRANSMITTER BUOY T-l455/BRT-6 PP-7806/B RT-6 RADIO TRANSMITTER BUOY T-1455/BRT-6 INTERCONNECTING CABLE ASS EM B LY, CX- 1 3 3 1 8/BRT-6 I 1 4 I RADIO TRANSMITTER BUOY T-l455/BRT-6 I UNIT (BIU) I ),

26、 RADIO TRANSMITTER BUOY J-3958/B RT-6 w T- 1 455/B RT-6 1 REMOTE INDICATOR CABLE ASSEMBLY CHANNEL. ONE, CX-13319/BRT-6 REMOTE INDICATOR CABLE ASSEMBLY CHANNEL TWO, CX-13321/BRT-6 FIGURE 1. Buoy Transmitting Set, AN/BRT-6 block diagram. 5 Provided by IHSNot for ResaleNo reproduction or networking per

27、mitted without license from IHS-,-,-MIL-C-29512( EC) 3.2.1 Prime power. Prime power shall be 115 volts alternating current (VAC), 60 hertz (Hz), single-phase, Type I, in accordance with DoD-STD-1399, Section 300. The power is connected via J1 as shown in FIGURE 2. Total current draw shall not exceed

28、 2 amperes (amp). The alternating current (AC) power switch shall be a two-position switch located on the front panel and shall be labeled with ON and OFF designations. A power indicator shall be located on the front panel and shall be labeled POWER ON. The power indicator shall be connected across

29、the input power conductors on the load side of the switch. The AC input fuses, F1 and F2, shall be located on the front panel and labeled with their corresponding values, AC input lines shall be fused at the load side of the power switch as shown in FIGURE 2 and shall have blown fuse indicators. Spa

30、re fuses shall be located within the BC. 3.2.2 Elapsed time meter. An elapsed time meter, M2, shall be located on the front panel and labeled OPERATING. M2 shall display accumulative on-time of prime power. The M2 fuse, F3 (see FIGURE 21, shall be located on the front panel, labeled with its value a

31、nd have a blown fuse indicator. 3.2.3. Charger outputs. The BC shall provide 12 charging outputs consisting of one high (HI) and one low (LO) voltage output for each of the six buoys in accordance with FIGURE 2. The HI voltage charging output shall be 65 volts direct current (VDC) I10 volts (VI open

32、-circuit voltage and shall be a constant current source of 50 milliamperes (mA) *5 mA. The LO voltage charging output shall be 30 VDC *7 V open-circuit voltage and shall be a constant current source of 150 mA *15 mA. 3.2.4 Charging meter. Meter M1 shall be located on the front panel and shall be use

33、d to measure voltage and current of each of the 12 charger outputs (see 3.2.3). -The meter scale shall have linear black divisions with full scale values of 35 V, 75 V, 75 mA, and 225 mA. The scale background coloring shall be red from O percent to 50 percent of full scale, green from 50 percent to

34、75 percent of full scale, and white from 75 percent to 100 percent of full scale. The remainder of the meter scale face shall be white. The overall accuracy of the meter shall be 5 percent, 3.2.4.1 Buoy select switch. A 12-position switch shall be located on the front panel and labeled BUOY SELECT w

35、ith a position designation for each charger output. The BUOY SELECT switch shall be used to select which one of the 12 charging outputs will be measured by meter M1. 3.2.4.2 Meter select switch. A two-position switch shall be located on the front panel and labeledR SELECT with two positions labeled

36、CURRENT and VOLTAGE. The METER SELECT switch shall be used to select whether voltage or current is measured by meter M1. . 3.2.5 Leakage current. The leakage current shall not exceed 5 mA, 6 1 I I L a e I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

37、-,-c PRIME POWER 115 VAC L MIL-C-27512 58 W 7777706 O1570b9 3 M MIL-C-29512( EC) -ELAPSED I AC POWER II SWITCH 1 - - SELECT SWITCH CHARGING METER METER SELECT SWITCH POWER SUPPLY J2 1 Lo V BUOY #1 Gnd E Hi 1 2 13 19 3 4 Gnd 14 20 15 21 E Gnd Hi “I 5 6 LoV BUOY #3 7 8 Lo V BUOY #4 Gnd , 16 22 Buoy#6

38、25 26 FIGURE 2. BC. - 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-235L2 58 9799906 OL57070-T-E- MIL-C-29512( EC) 3.3 Physical characteristics. The physical characteristics shall be as specified in 3.3.1 through 3.3.7. 3.3.1 Dimensions and

39、 weight. enclosure cabinet, and mounting plate. The BC shall conform to the dimensions shown in FIGURE 3. (lbs). Total weight of the Cable Kit shall not exceed 30 lbs and the length shall not exceed 30 feet. The BC shall consist of a front panel, The total weight of the BC shall not exceed 15 pounds

40、 3,3.2 Front panel. The BC front panel shall be hinged to the enclosure and, in the closed position, shall become the front surface of the enclosure. The front panel shall attach to the enclosure by captive screws. Front panel controls, indicators, and labels shall be in accordance with FIGURE 4. 3.

41、3.3 Mounting plate heat sink. The mounting plate shall be the rear surface of the enclosure and shall be used as a heat sink so that forced air cooling is not necessary. 3.3.4 Human engineering. The BC shall conform to the human engineering operational and maintenance design cri teria of MIL-STD-147

42、2. The design of the operator and maintainer panel layouts and controls shall conform to 3.3.2 and MIL-STD-1472. 3.3.5 Accessibility. Accessibility shall be in accordance with MIL-STO-454, Requirement 36. An automatically operated lock shall be provided to lock the access door in the servicing posit

43、ion. 3.3.6 Cables and connectors. Cables and connectors shall be as specified in 3.3.6.1 through 3.3.6.4. 3.3.6.1 Cable Kit. The Cable Kit shall be in accordance with NAVSEA Drawing F53711-409-6379608 and MIL-C-24643/45. 3.3.6.2 BC internal cabling. Sufficient cable shall be provided internal to the

44、 enclosure to accommodate front panel opening. The cables shall be arranged and guided to prevent snagging or interference during front panel extension. 3.3.6.3 Connectors. All external electrical connectors shall be located on the right side of the enclosure and shall be in accordance with MS 27505

45、, the types specified in TABLE I, MIL-STD-1683, and MIL-C-28840. TABLE I. External connectors. Connector TY Pe J1 MS 27505E-17B-6P 52 MS 27505E- 15B-35SA L 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-27512 58 W 7777706 015707L L M MIL-C-2

46、9512( EC) r 5r PIVOT POINT TOP 1-5.64 -4 RIGHT SIDE FRONT Note: 1. Unless otherwise specified, all tolerances are k0.05. 2. All dimensions are in inches. FIGURE 3. BC dimensions. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-C-27512 58 W 77

47、77706 0157072 3 W MIL-C-29512( EC) OPERATING 6 POWER ON O HIGH CHARGE O LOW CHARGE CURRENT I VOTAGE METER SELECT I I I I l I 9 8 7 6 54 1. VOLT/AMP METER (Ml) 2. BUOY SELECT SWITCH 3. OPERATING METER (M2) 4. POWEROWOFF 5. AC POWER ON INDICATOR 6. 114 AMP FUSE (F3) 7. 2 AMP FUSE (F2) 8. 2 AMP FUSE (F

48、l) 9. METER SELECT SWITCH . FIGURE 4. BC controls and indicators (front view). 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-275L2 5 W 7777906 0357073 5 W 3.3.6.4 Power connections. 115 VAC power. cable connections within the BC shall have

49、 the color and conductor assignments specified in TABLE TI. designations shall be as specified in TABLE II. shall be maintained from the BC input connections to all components with the same voltage and frequency as the input power. Pin Conductor insulation color TABLE II. Pin designation - 115 VAC equipment power connections. Conductor assignment I Insu1 ation color 415 V