NAVY MIL-A-21016 F-1990 ADHESIVE RESILIENT DECK COVERING《甲板弹力覆盖物粘合剂》.pdf

《NAVY MIL-A-21016 F-1990 ADHESIVE RESILIENT DECK COVERING《甲板弹力覆盖物粘合剂》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-A-21016 F-1990 ADHESIVE RESILIENT DECK COVERING《甲板弹力覆盖物粘合剂》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-A-2LOLbF 80 W 7777706 0435Lb b (INCH-POUND MIL-A-21016F 21 Mav 1990 SUPERSEDING 26 January 1967 (See 6.6) MIL-A-21016E MILITARY SPECIFICATION ADHESIVE, RESILIENT DECK COVERING This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 SCOIE.

2、 This specification establishes the requirements for the adhesive for securing resilient coverings to decks. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 SDecifications. stan-ards. ant andbooks. The following spec .ca- tions, standards, and handbooks form a part of this document to the ex

3、tent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL PPP-C-96 - Cans, Metal, 28 Ga

4、ge and Lighter. PPP-F-320 - Fiberboard: Corrugated and Solid, Sheet Stock PPP-P-704 - Pails, Metal: (Shipping, Steel, 1 Through 12 Gallons), (Container Grade), and Cut Shapes. I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this d

5、ocument should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposa1 (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8040 DISTRIBUTIO

6、N STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-A-2101bF 0 777770b 0435387 W MIL-A-21016F MILITARY MIL-T-I8830 - Tile, Plastic, Fire-Retardant. MIL-L-19140 - Lumber and Plywo

7、od, Fire-Retardant Treated. MIL-A-21366 - Adhesive, for Bonding Plastic Table Top Material to Aluminum. STANDARDS FEDERAL * FED-STD-313 - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities. MI LI TARY MIL-STD-105 - Sampling Procedur

8、es and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-147 - Palletized Unit Loads. Attributes. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building

9、4D; 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents. drawings. and Publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited

10、 in the solicitation. DEPARTMENT OF LABOR Occupational Safety and Health Administration (OSHA) Code of Federal Regulations (CFR) Title 29, Part 1910 Section 1200 (Application for copies should be addressed to: Occupational Safety and Health Administration, Office of Publications, 200 Constitution Av

11、enue N.W., Room N3101, Washington, DC 20210.) 2.2 Non-Government Publications. The following document forms a part of Unless otherwise specified, the this document to the extent specified herein. issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the s

12、olicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 1849 - Standard Test Method for Packaging Stability of Paint. D 3951 - Standard Practice

13、for Commercial Packaging. (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-2LOLbF 0 9777706 OLI35LB T W D

14、rying time (hours) 1 . . 96 MIL-A-21016F Load at separation Type of tile (pounds) Plastic 1.5 Plas tic 7.5 (Non-Government standards and other publications are normally available from the organizations which prepare or which distribute the documents. documents also may be available in or through lib

15、raries or other informational services, ) These 2.3 Order of Drecedence. In the event-of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a sp

16、ecific exemption has been obtained. 3. REQUIREMENTS 3.1 Material. The adhesive shall be a waterbase latex free of all ingredi- ents which may affect the serviceability or have a deleterious effect on metal, resilient deck covering and deck underlayment. 3.1.1 General reauirement. The adhesive shall

17、be free from grits, lumps, and skins, and shall be suitable for application with a trowel (see 4.4.1). It - addition of other ingredients. 3.1.2 Stability. The adhes.ive shall not deteriorate (see 4.4.2). 3.1.3 Prohibited fibers. Neither asbest shall be suitable and effective for the-purpose intende

18、d without heating or liver, settle, or otherwise s nor ceramic (refractor) fiber nor materials containing any of these fibers shall be use.d in the adhesive formulation (see 6.3). 3.2 Edge-adhesive strength. The adhesive shall have edge adhesive strengths not less than those specified in table I (se

19、e 4.4.3). TABLE I. Edge adhesive strength. . 3.3 Edge adhesive strength after water immersion. The adhesive shall have edge adhesive strengths not less than 6 pounds (see 4.4.4). 3.4 Corrosion of metal. The adhesive shall not corrode metal (see 4.4.5). 3.5 Viscositv. centipoises (see 4.4.6). The vis

20、cosity of the adhesive shall be not less than 20,000 -3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-2LO3bF 80 m 777770b 0435387 I m MIL-A-21016F 3.6 Marking. Each container of material shall be provided with a label giving adequate instruct

21、ions for its use and application. 3.7 Material safetv data sheets. The manufacturer shall provide the contracting activity with a Material Safety Data Sheet (MSDS) at the time of contract award. The MSDS is Form OSHA-20, found in and part of FED-STD-313 (see 6.4) and 29 CFR 1910.1200, Hazard Communi

22、cation. When FED-STD-313 is at variance with the CFR, 29 CFR 1910.1200 shall take precedence, modify and supplement FED-STD-313. The MSDS shall be included with each shipment of the material covered by this specification (see 6.4). 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inmection. Un

23、less otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other faci

24、lities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform ny of the inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and services con

25、form to prescribed requirements, 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requireme

26、nts in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies sub- mitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of the manufacturing operations, is an acceptable practice

27、 to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.2 Sampling for inspection. Sampling for inspection shall be as specified in 4.2.1 through

28、4.2.3. 4.2.1 m. For purposes of inspection, a lot shall consist of all adhesive from one production batch offered for delivery at one time. , 4.2.2 Sampling for examination of filled-containers. A random sample of filled containers shall be selected from each lot in accordance with MIL-STD-105 at in

29、spection level I (see 4.3.1). 4.2.3 SamDline: for tests. From each lot, two containers shall be selected. From each of the containers, 2-quart samples shall be taken for the tests specified in 4.3.2. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

30、MIL-A-21016F 4.3 Oualitv conformance inspection. Quality conformance inspection shall be Quality conformance inspection shall be the provided in accordance with table II. contractors responsibility with verification by the Defense Contract Admini- stration Services Management Area (DCASMA) (see 6.3)

31、, TABLE II. Ouality conformance inspection. Inspection Material S tab il i ty Edge adhesive strength before water immersion after water immersion Corrosion Markings Viscosity Requirement 3.1 hall be backed with 1/32-inch aluminum using a contact adhesive conforming to MIL-A-21366. aluminum and the w

32、earing surface of the tiles has been ensured, the pieces of tile shall be secured to the steel plates in accordance with 4.4.1 in such a manner that a 1- by 3-inch portion of the tile extends beyond the edge of the plate. Support the extended portion of the tile with a 1/8-inch thick steel plate. en

33、tire tile shall then be rolled to insure that the tile at the edge of the steel plate is securely bonded. machine direction of the tile. The wearing surfaces of 3-inch by 4-1/2 After a proper bond between the The The longer dimension of the specimen shall be in the 4.4.3.2 SDecimen ErouDs. - The spe

34、cimens shall be divided into two groups. One group shall be allowed to set for 1 hour prior to test, the second group for 96 hours. 4.4.3.3 Procedure. The steel plate shall be securely fixed to a suitable testing machine (such as an Instron Tester). placed under the extended portion of the specimen

35、and shall be raised (relative to the steel plate) in a direction perpendicular to the plane of the tile at a rate of 1 inch per minute in order to lift the tile away from the steel plate. load at 1/8 inch separation of the tile from the plate shall be determined to the nearest 0.1 pound and shall be

36、 taken as the edge adhesive strength. A 1/4 inch diameter rod shall be The 4.4.4 Edge adhesive strength after water immersion. Specimens shall be prepared as specified in 4.4.3.1 and shall be allowed to set for 96 hours prior to test. tap water at 70 When specified (see 6.2), pails shall be palletiz

37、ed in accordance with MIL-STD-147. 5.3.2 Level B. 5.3.2.1 Cans. Cans shall be packed in accordance with the level A require- ments of the appendix to PPP-C-96 except that wood, plywood and wirebound boxes shall be of the domestic type or class. fiberboard top and pads. method V and reinforced with t

38、ape or non-metallic banding. Fiberboard boxes shall be provided with Fiberboard box closure shall be in accordance with 5.3.2.2 Pails. Pails are not required to be overpacked. When specified -a- (seeSa2), pails shall be palletized in accordance with MIL-STD-147. 5.3.3 Level C. -5.3.3.1 Cans. Cans sh

39、all be packed in accordance with the level B require- ments of the appendix to PPP-C-96. 5.1.1.2 and 6.2), fiberboard boxes shall be of the Class-Domestic/Fire-Retardant including the interior packing forms (top and bottom pads) which are required. Box closure shall be in accordance with method usin

40、g pressure sensitive adhesive tape. For Navy, unless otherwise specified (see 5.3.3.2 Pails. Pails are not required to be overpacked. When specified (see 6.2), pails shall be palletized in accordance with MIL-STD-147. 5.3.4 Commercial. Commercial packing requirements for cans and pails shall be in a

41、ccordance with ASTM D 3951. 5.4 Markinq. 5.4.1 Levels A. B. C. and commercial. In addition to any special marking required (see 6.2 and 3.6), unit containers (cans and pails), shipping containers and palletized unit loads shall be marked in accordance with MIL-STD-129. information shall include the

42、date of manufacture, batch or lot number, bar coding, and storage limitations (temperature, relative humidity). Commercial marking shall be in accordance with ASTM D 3951 including the label specified in 3.6, date of manufacture, batch or lot number, bar coding, and storage limitations (temperature,

43、 relative humidity). In addition, containers shall be marked “Adhesive free of asbestos and ceramic (refractory) fibers“, (see 3.1.3). Marking 5.5 Material safetv data sheet. A copy of the material safety data sheet shall be attached to the shipping document for each destination (see 3.7). 8 Provide

44、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-ZLOL6F 0 7999906 0435194 5 m MIL-A-21016F 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. This material is int

45、ended to secure resilient coverings to steel decks and to the underlayment of steel decks. 6.2 Acauisition reauirements. Acquisition documents should specify the following: (a) Title, number, and date of this specification. (b) Issue of DoDISS to be cited in the solicitation, and if required, (c) (d

46、) When fire-retardant treated material is required (see 5.1.1.1). (e) (f) (g) When palletization of pails is required (see 5.3.1.2, 5.3.2.2, and the specific issue of individual documents referenced (see 2.1.1) Inspection conditions other than specified herein (see 4.4.1). Unit pack quantity require

47、d (see 5.1.2) Level of preservation and level of packing required (see 5.2 and 5.3). 5.3.3.2). _- (h) Special marking required (see 5.4.1). _1 6.3 consideration of data requirements. The following data requirements should be considered when this specification is applied on a contract. The applicable

48、 Data Item Descriptions (DIDs) should be reviewed in conjunction with the specific acquisition.to ensure that only essential data are requested/provided and that the DIDs are tailored to reflect the requirements of the specific acquisition. a.Contract Data Requirements List (DD Form 1423) must be pr

49、epared to obtain the data, except where DoD FAR Supplement 27.475-1 exempts the requirement for a DD Form 1423. To ensure correct contractual application of the data requirements, Reference Paragraph DID Number DID Title Supvested Tailorin5 3.1.3 and 4.3.2 DI-E-2121 Certificate of compliance - 4.3 DI-T-2072 Test reports - The above DIDs were those cleared as of the date of this specification. current issue of DoD 5010.12-L, Acquisition Management Systems and D