HOLDEN HN 2090-2005 Adhesive - Structural - Two Component - Part B《粘接剂 结构类 双组分 组分B》.pdf

《HOLDEN HN 2090-2005 Adhesive - Structural - Two Component - Part B《粘接剂 结构类 双组分 组分B》.pdf》由会员分享，可在线阅读，更多相关《HOLDEN HN 2090-2005 Adhesive - Structural - Two Component - Part B《粘接剂 结构类 双组分 组分B》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2090 1 of 3 February, 1993 March, 2005 NAME: ADHESIVE - STRUCTURAL - TWO COMPONENT - PART B THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPI

2、ENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 1. SCOPE The material described in this specification is the Part B (or catalyst) component of a two-part pumpable structural adhesive system. The adhesive s

3、ystem is used for bonding oily and unclean metal substrates, such as galvanized steel, zinc coated steel and CRLC as used for inner and outer panels (hems) of engine hoods, deck lids and doors. 2. PROPERTIES 2.1 Viscosity Test Method HN 0060 Meter 1 Procedure A 550 kPa air pressure 2.1.1 As Received

4、 30 - 50 seconds 2.1.2 Aged Viscosity 7 seconds maximum increase 7 days 40 2 C over initial Viscosity. 2.1.3 After Storage 12 seconds maximum 3 months 27 2 C increase over initial Viscosity. 2.2 Solids (ASTM D2834) 100% Sample dried at 102 3 C for 3 hours. 2.3 Colour Black (Versilok 270), Grey (Vers

5、ilok 254) 2.4 Storage The material should be stored away from heat sources at a temperature no higher than 27 C. When the storage temperatures have been below 20 C it will be necessary to store the container for 24 hours at 20 - 27 C prior to pumping. This conditioning is necessary to allow optimum

6、application properties. 2.5 Shelf Life When stored under the conditions of Clause 2.4 the shelf life shall be 3 months minimum. A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2090 2 of 3 February, 1993 March, 2005 NAME: ADHESIVE - S

7、TRUCTURAL - TWO COMPONENT - PART B THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 3. APPROVAL, INSPECTION AND R

8、EJECTION Refer HN 1000, Clauses A, C and G(Line Trial). 4. HAZARDOUS MATERIALS Refer HN 1000, Clause H. 5. RESTRICTED AND REPORTABLE SUBSTANCES Refer HN 1000, Clause J. 6. APPROVED SUPPLIERS AND MATERIALS Material known to meet the full requirements of this specification: SUPPLIER MATERIAL LORD CHEM

9、ICAL PRODUCTS AUSTRALIA PTY LTD LORD CORPORATION, USA Versilok 270 (Black bulk material) LORD CHEMICAL PRODUCTS AUSTRALIA PTY LTD LORD CORPORATION, USA Versilok 254 (Grey for cartridge only) 7. REFERENCES ASTM D2834 HN 1000 A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICAT

10、ION NUMBER SHEET RELEASE REVISION : HN 2090 3 of 3 February, 1993 March, 2005 NAME: ADHESIVE - STRUCTURAL - TWO COMPONENT - PART B THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM :

11、 I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 8. REVISIONS March 2005 - Revised section 2.3 Colour (of section2.PROPERTIES). Colour reference is made to Versilok 270 and Versilok 254. - Removal of reference to HN 1000 Clause B in section 3.APPROVAL, INSPECTION AND REJECTION. - T

12、ransfer of the information on HN 2090 APPROVED SOURCES SHEET into section 6.APPROVED SUPPLIERS AND MATERIALS - Revised section 6.APPROVED SUPPLIERS AND MATERIALS. - Added the material and supplier - Versilok 254 - Revised supplier of Versilok 270 - Added sections 4.HAZARDOUS MATERIALS, 5.RESTRICTED AND REPORTABLE SUBSTANCES AND 7.REFERENCES. Prepared By: Y. Zia