GMKOREA EDS-T-5246-2008 SALT SPRAY TEST FOR ELECTRIC AND ELECTRONIC COMPONENTS IN VEHICLE.pdf

《GMKOREA EDS-T-5246-2008 SALT SPRAY TEST FOR ELECTRIC AND ELECTRONIC COMPONENTS IN VEHICLE.pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-T-5246-2008 SALT SPRAY TEST FOR ELECTRIC AND ELECTRONIC COMPONENTS IN VEHICLE.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards SALTSPRAYTESTFORELECTRICANDELECTRONICCOMPONENTSINVEHICLE Do Not Use on New Programs. Being Replaced by GMW3172&14872 EDS-T-5246 ISSUED DATE : 1997. 05. 07 REVISED DATE : 2008. 10. 21 VERSION: 3 (Superceded) EDS-T-5246

2、SALTSPRAYTESTFORELECTRICANDELECTRONICCOMPONENTSINVEHICLE PAGE: 1/2 ISSUED DATE: 1997. 05. 07 REVISED DATE: 2008. 10. 21 VERSION: 3 GM DAEWOO Auto & Technology Note: This standard may be applied only for current project (incl. T255 Program). It is Superceded for all future projects and replaced by GM

3、W3172&14872. 1. PURPOSE AND APPLICATION This test method describes the test cycle for performance of a salt spray test for electric/electronic components in vehicle which are not mounted in vehicle internal space. Furthermore, details over requirements to these components are also included. 2. TEST

4、SAMPLE AND TEST AMOUNT 2.1. Unless otherwise specified, tests are to be performed at finish parts or complete assembly. 2.2. Unless otherwise specified, minimum 3 piece of concerned components are to be delivered for first sampling and release test to this specification. 3. TEST EQUIPMENT 3.1. Test

5、equipment to EDS-T-7143 3.2. Thermal cabinet with natural ventilation, controllable, which is able to hold constantly required temperatures within 2.5K. 3.3. Controllable voltage source 0 to 24V, minimum loadability 25A, for voltage supply of specimen. 4. PERFORMANCE 4.1. The test is to be performed

6、 at components with all connections, cables and plugs with electric supply and mounted in mounting position. 4.2. Temporal process 4.2.1. Thermal pretreatment Temperature storage of component for 1h at +802.5K(without electric function). 4.2.2. Cycle(1 week) 24 h storage in salt spray fog to EDS-T-7

7、143 6 h drying time in thermal cabinet at +402.5K 18 h storage in salt spray fog to EDS-T-7143 6 h drying time in thermal cabinet at +402.5K 18 h storage in salt spray fog to EDS-T-7143 6 h drying time in thermal cabinet at +402.5K 24 h storage in salt spray fog to EDS-T-7143 EDS-T-5246SALTSPRAYTEST

8、FORELECTRICANDELECTRONICCOMPONENTSINVEHICLE PAGE: 2/2 ISSUED DATE: 1997. 05. 07 REVISED DATE: 2008. 10. 21 VERSION: 3 GM DAEWOO Auto & Technology 65 h drying time in thermal cabinet at +402.5K 4.2.3. Repeat of week cycle corresponding to clause 4.2.2 4.3. Electric stress of components during test pr

9、ocess 4.3.1. During storage in salt spray fog, the board mains voltage is applied at component as in vehicle in state: “ignition on“. 4.3.2. The component is switched on during this time every 20 minutes for 10 minutes according to function. This can be either a permanent switching-on or a switching

10、-on with equal rhythm, as it is required at fatigue test of component specified in the respectively concerning technical delivery conditions. 4.3.3. With beginning of drying times specified under clause 4.2.2, the voltage supply of component is disconnected(as in vehicle in state: “ignition off“). 4

11、.3.4. 10 minutes before passing of respective drying time, the component is tested switched-on as under clause 4.3.1 and according to function. 4.3.5. Deviations from here defined electric stress are determined in technical delivery conditions accurate for the test part. 5. REQUIREMENTS During and a

12、fter this test process the function of component must be guaranteed, the functional values must be within tolerance ranges prescribed in valid technical delivery conditions or on drawing. 6. DETAILS IN DRAWINGS, TEST SPECIFICATIONS AND SUCH THINGS This test method is specified in drawings, test spec

13、ifications and such things as follows: Salt spray test to EDS-T-5246 test method marking 7. DEVIATIONS Deviations from conditions of this test method must be agreed. These conditions are prescribed in component drawings, material specifications and such things or must be specified in test certificates, reports and such things.