FORD WSS-M7H58-A-2010 WEBBING HIGH STRENGTH LOW ELONGATION 18 FINE PANEL HERRINGBONE WEAVE TO BE USED WITH FORD WSS-M99P1111-A 《高强度低伸长率的18优良面板交叉编织的织带 与福特WSS-M99P1111-A 一起使用》.pdf

《FORD WSS-M7H58-A-2010 WEBBING HIGH STRENGTH LOW ELONGATION 18 FINE PANEL HERRINGBONE WEAVE TO BE USED WITH FORD WSS-M99P1111-A 《高强度低伸长率的18优良面板交叉编织的织带 与福特WSS-M99P1111-A 一起使用》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M7H58-A-2010 WEBBING HIGH STRENGTH LOW ELONGATION 18 FINE PANEL HERRINGBONE WEAVE TO BE USED WITH FORD WSS-M99P1111-A 《高强度低伸长率的18优良面板交叉编织的织带 与福特WSS-M99P1111-A 一起使用》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2010 03 04 N-STATUS No replacement named L. Sinclair, NA 2001 08 30 Revised Added WSS-M7H59-A, updated WSS-M7H58-A title J. Faunt 2001 07 19 Activated J. Faunt Printed copies are uncontrolled Page 1 of 4 Cop

2、yright 2010, Ford Global Technologies, Inc. WEBBING, HIGH STRENGTH, LOW ELONGATION, 18 FINE WSS-M7H58-A PANEL HERRINGBONE WEAVE WEBBING, MEDIUM STRENGTH, LOW ELONGATION, 9 PANEL WSS-M7H59-A WIDE BORDER WEAVE NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by these specifications are sea

3、t belt webbings woven with either twisted or untwisted continuous filament yarns and finished selvages and may have a monofilament reinforcement. WSS-M7H58-A is an 18 fine panel herringbone weave and WSS-M7H59-A is a 9 panel wide border weave. Proper dyes and dyeing procedures shall be employed, the

4、 yarns may be spun dyed or the webbing may be piece dyed to provide acceptable color, appearance, and physical properties. A surface finish may be applied to enhance abrasion resistance and/or surface friction. Color stripping for redyeing of webbing rejected for color is not allowed. The webbing sh

5、all be of good quality and uniform construction. 2. APPLICATION These specifications were originally released for materials used in the manufacture of seat belts. 3. REQUIREMENTS In addition to the requirements listed herein, materials approved to these specifications must also meet all applicable r

6、equirements of marketplace National Standards such as C/FMVSS 209, ECE 16, ADR 4, JIS D4604, etc. Material specification requirements are to be used for initial qualification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to the Companys Quality Syst

7、em Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra and thermograms that corre

8、spond to the reference standard when tested under the same conditions. ENGINEERING MATERIAL SPECIFICATION WSS-M7H58-A/59-A Page 2 of 4 Copyright 2010, Ford Global Technologies, Inc. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlle

9、d atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. 3.4 APPEARANCE The color, pattern and finish shall match the initial construction approved by Design Center. WSS-M7H58-A is to be manuf

10、actured in an 18 fine panel herringbone weave construction (not including the edges as panels). WSS-M7H59-A is to be manufactured in a 9 panel wide border weave construction (not including the edges as panels). WSS-M7H58-A WSS-M7H59-A 3.5 BREAKING STRENGTH, kN, min 27.0 24.75 (SAE J140, using 100 mm

11、 diameter jaws) 3.6 ELONGATION, %, range 6-10 6 10 (FMVSS 209, S5.1(c) 3.7 RESISTANCE TO FADE, min (SAE J1885, ISO 105 A-02/AATCC Evaluation Procedure 1) 3.7.1 225.6 kJ/m2, all colors Webbing using spun dyed yarns Rating 4 Piece-dyed webbing Rating 3 3.7.2 488.6 kJ/m2, black only, all types Rating 3

12、 No individual yarn or combination of yarns shall fade, stain or exhibit any color tone change, nor shall the yarns change in hue or brightness in excess of the above ratings. 3.8 COLORFASTNESS TO CROCKING, WET AND DRY, min Rating 4 (FLTM BN 107-01, AATCC Evaluation Procedure 2) 3.9 COLORFASTNESS TO

13、 STAINING-BLEEDING, min Rating 4 (FLTM AN 101-01, AATCC Evaluation Procedure 2) 3.10 PERSPIRATION STAINING, min Rating 4 (FLTM AN 101-01, AATCC Evaluation Procedure 2) ENGINEERING MATERIAL SPECIFICATION WSS-M7H58-A/59-A Page 3 of 4 Copyright 2010, Ford Global Technologies, Inc. 3.11 SOILING AND CLEA

14、NABILITY (FLTM BN 112-08) The performance of production material shall be equal to or better than that exhibited by the sample originally approved for production by the Materials Engineering Activity. 3.12 PLIABILITY (FLTM BN 102-05, ASTM D 747 (direct reading at 60 degrees, 12.7 mm span length) Pli

15、ability requirements will vary depending on individual vehicle system needs and marketplace. Therefore, pliability test method and requirements are to be agreed upon by the seatbelt system and webbing suppliers. The method and agreed upon requirements will be submitted with the initial source approv

16、al and made a part of the record. Any requirement changes in excess of +/- 15 % for a currently approved construction will require a new approval submission. 3.13 FOGGING (SAE J1756, 3 h at 100 C heating, 21 C cooling plate, post test conditioning 1 h and 16 h) Fog Number, min 70 Formation of clear

17、film, droplets or crystals is cause for rejection. 3.14 ODOR, Rating, max 2 (FLTM BO 131-01) 3.15 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute 3.16 ADDITIONAL REQUIREMENTS Additional requirements for material and/or manufactured parts may be specified on the Engineering drawing, Eng

18、ineering parts specification, performance specification, System Design Specification (SDS) and/or Component Design Specification (CDS). 3.16.1 Crease Recovery The seat belt system manufacturer and/or the vehicle assembly plant may require specific crease recovery requirements, where induced creasing

19、 of the webbing may be caused by specific folding requirements and/or storage. The induced creasing on the webbing may, under certain circumstances, prevent the webbing from retracting fully. The test method and specific measured values, should be added to the Engineering Drawing and agreed upon bet

20、ween the supplier and the affected Materials Engineering and Restraints Engineering Activities. ENGINEERING MATERIAL SPECIFICATION WSS-M7H58-A/59-A Page 4 of 4 Copyright 2010, Ford Global Technologies, Inc. 3.17 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent

21、 in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the

22、 affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notification of the Company, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested

23、. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in Restricted Substance Management Standard WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to

24、 the Company must have prior approval. Certain materials subcontracted by part suppliers may also require prior approval. These include materials critical to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desiring approv

25、al of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstra

26、ting full compliance with all the requirements of this specification. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 Purchase departments will ensure that materials defined in the specification and shipped to any one vehicle in an assembly plant will be produced by one supplier only.