ASTM C1173-2010(2014) Standard Specification for Flexible Transition Couplings for Underground Piping Systems《地下管道系统用柔性过渡管联接器的标准规格》.pdf

《ASTM C1173-2010(2014) Standard Specification for Flexible Transition Couplings for Underground Piping Systems《地下管道系统用柔性过渡管联接器的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1173-2010(2014) Standard Specification for Flexible Transition Couplings for Underground Piping Systems《地下管道系统用柔性过渡管联接器的标准规格》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1173 10 (Reapproved 2014)Standard Specification forFlexible Transition Couplings for Underground PipingSystems1This standard is issued under the fixed designation C1173; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,

2、 the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification describes the properties of devices orassemblies suitable for use as flexible transiti

3、on couplings,hereinafter referred to as couplings, for underground drainageand sewer piping systems.1.2 Couplings that may include bushings, inserts, or shearrings and conform to the requirements of this standard aresuitable for joining plain end pipe or fittings. The pipe to bejoined shall be of si

4、milar or dissimilar materials, size, or both.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 The ASTM standards referenced herein

5、 shall be consid-ered mandatory.1.5 The committee with jurisdiction over this standard is notaware of another comparable standard for materials covered inthis standard.2. Referenced Documents2.1 ASTM Standards:2A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, a

6、nd Strip for PressureVessels and for General ApplicationsA493 Specification for Stainless Steel Wire and Wire Rodsfor Cold Heading and Cold ForgingA644 Terminology Relating to Iron CastingsD395 Test Methods for Rubber PropertyCompression SetD412 Test Methods for Vulcanized Rubber and Thermoplas-tic

7、ElastomersTensionD471 Test Method for Rubber PropertyEffect of LiquidsD543 Practices for Evaluating the Resistance of Plastics toChemical ReagentsD573 Test Method for RubberDeterioration in an AirOvenD624 Test Method for Tear Strength of Conventional Vul-canized Rubber and Thermoplastic ElastomersD6

8、38 Test Method for Tensile Properties of PlasticsD1149 Test Methods for Rubber DeteriorationCracking inan Ozone Controlled EnvironmentD2240 Test Method for Rubber PropertyDurometer Hard-nessD3045 Practice for Heat Aging of Plastics Without LoadD6147 Test Method for Vulcanized Rubber and Thermoplas-t

9、ic ElastomerDetermination of Force Decay (StressRelaxation) in Compression3. Terminology3.1 DefinitionsFor definitions of terms used in thisstandard, see Terminology A644.3.2 Definitions of Terms Specific to This Standard:3.2.1 center stop, nan integral part of the gasket centeredon its axial length

10、 intended to limit the insertion depth of thepipe to be coupled.3.2.2 clamp assembly, nthat portion of the coupling ex-cluding the gasket.3.2.3 coupling, nthe complete assembly.3.2.4 fitting, nparts of a pipeline other than straight pipecouplings, or valves.3.2.5 flexible transition couplings, ndevi

11、ces used to forma leakproof joint between sections of plain end pipe or fittingsof the same or different materials, of the same or different size,or any combination of materials or pipe sizes.3.2.6 free torque, nthe torque value expressed inlbfin./Nm when the clamp is tightened four revolutions of t

12、hescrew nut; while in the free state, this value does not includeany breakaway effects due to staking or passage of the bandends beyond the screw heads.3.2.7 inserts, na bushing or ring placed into the couplingsocket to accommodate pipe materials of differing outsidediameters.1This specification is

13、under the jurisdiction of ASTM Committee A04 on IronCastings and is the direct responsibility of Subcommittee A04.75 on Gaskets andCoupling for Plumbing and Sewer Piping.Current edition approved Oct. 1, 2014. Published October 2014. Originallyapproved in 1991. Last previous edition approved in 2010

14、as C1173 10. DOI:10.1520/C1173-10R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM Internati

15、onal, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.2.8 joint, nthe completed assembly of parts consistingof the flexible transition coupling and the joined pipes, orfittings, or both.3.2.9 lot, na specific quantity of similar material orcollection of similar

16、units from a common source; the quantityoffered for inspection and acceptance at any one time. A lotmight comprise a shipment, batch, or similar quantity.3.2.10 manufacturer, nthe entity that produces the cou-pling.3.2.11 plain end pipe, nany pipe that does not include anybell, hub, threaded area, o

17、r other means of joining.3.2.12 shear ring, nan interior or exterior element whichis used to span the distance between the pipe ends within acoupling so as to provide increased resistance to axial displace-ment.4. Classification4.1 The couplings shall be permitted to have a center stop.The component

18、s shall be designed so that the elastomericmaterial is compressed to form a hydrostatic seal when thejoint is assembled. The couplings shall be of the typesdescribed in 4.1.1 4.1.3.4.1.1 Type AA coupling consisting of an elastomericgasket incorporating corrosion resistant tension bands andtightening

19、 mechanism. Couplings shall be fabricated withoutshear rings, with or without inserts and with or without a centerstop.4.1.2 Type BA coupling consisting of an elastomericgasket incorporating a corrosion resistant shear ring, tensionbands and tightening mechanism. Couplings shall be fabricatedwith sh

20、ear rings, with or without inserts and with or without acenter stop (Note 1).4.1.3 Type CA coupling fabricated with elastomeric com-pression seals.NOTE 1The provisions of this standard are not intended to prevent theuse of any alternate material or method of construction, provided any suchalternate

21、meets the requirements of this standard.5. Materials and Manufacture5.1 Elastomeric materials used in the manufacturing ofcouplings and inserts shall comply with the requirements ofsection 10.1 and Table 1 of this standard.5.2 All metallic components shall be manufactured of 300series stainless stee

22、l.6. Elastomeric Gasket Requirements6.1 The elastomeric gasket shall conform to the physicalproperties as specified in section 5.1 of this standard.6.2 Elastomeric gaskets and inserts of single, multi-piece, orspliced construction shall show no signs of separation, peeling,or other defects when test

23、ed in accordance with Section 9.6.3 Elastomeric gaskets and inserts of single, multi-piece, orspliced construction shall be free from porosity and air pockets.Its surface shall be smooth and free from pitting, cracks,blisters, air marks, or any other imperfections that affect itsperformance in servi

24、ce. The flash extension shall not exceed 1mm at any point where the presence of flash affects perfor-mance.6.4 Elastomeric gaskets and inserts shall be compatible withthe dimensions and tolerances of the specific material to whichit is designed to join.7. Clamp Assembly Requirements7.1 All metallic

25、components shall be of 300 series stainlesssteel conforming to the requirements of Specification A240/A240M. All metallic components made from round stock shallbe of 300 series stainless steel conforming to the requirementsof Specification A493 (excluding copper bearing alloys).7.2 Clamp assemblies,

26、 tension bands, tightening mecha-nisms shall conform to the performance requirements as setforth in section 10.2 of this standard.8. Dimensions8.1 Couplings and bushing dimensions shall be compatiblewith the dimensions and tolerances of the specific material towhich it is designed to join.9. Samplin

27、g, Tests, and Retests9.1 Test specimens representative of the couplings to beused shall be randomly selected from the manufactured lot fortesting.9.2 One coupling for each size or type shall be tested, unlessotherwise specified or waived by the purchaser.9.3 Where there is a failure in the original

28、test, the entire testshall be rerun with twice the number of samples and any failureshall be cause for rejection.10. Test Methods10.1 Elastomeric Materials:TABLE 1 Test RequirementsPropertiesPhysicalRequirementsASTM TestMethodElastomeric MaterialsHardness, Nominal Shore “A” Durometeras specified by

29、the coupling manufacturer5075 D2240Hardness, Nominal Shore “D” Durometeras specified by the coupling manufacturer3545 D2240Tensile strength, min psi (KPa) 1000 (6894) D412,DieC,Fig. 2 or D638Elongation at rupture, min, % 200 D412,DieC,Fig. 2 or D638Heat aging, 70 h, 158 3.6F (70 2C) D573 or D3045Har

30、dness increase, maximum Durometerpoints10Change in tensile strength, max, % 25Change in elongation, max, % 35Ozone resistance No cracks D1149At 20 % elongationFor 100 h at 104 3.6F (40 2C)With 50 parts per 100 millionWater absorption, weight gain, %, max 20 D471Chemical resistance, 48 h, 74 3.6F (23

31、 2C)no weight loss D543Compression Set, max, % 25 D395 Method BStress Relaxation, min. % Force Retention 30 D6147Tear Strength, min, lbf/in. (N/cm) 150 (268.5) D624 Die CC1173 10 (2014)210.1.1 HardnessHardness shall be measured on either afinished surface, a squarely cut end, or a flat sliced or buf

32、fedsurface, depending on the size and shape of the specimen. SeeTest Method D2240. The manufacturer shall specify thehardness and scale.10.1.2 Tensile Strength and Elongation The dumbbellsshall be prepared from sections of the finished material. SeeTest Method D412.10.1.3 Heat Agingfor hardness, ten

33、sile and elongationshall be performed in accordance with Test Method D573.Specimens shall be oven-aged for 96 h at 158 6 3.6F (70 62C).10.1.4 Ozone ResistanceSee Test Method D1149. Proce-dure A, stretched 20 % and exposed to an ozone concentrationof 50 parts per 100 million for 100 h at 104 6 3.6F (

34、40 62C).10.1.5 Water AbsorptionSize and time determinationsshall be set in accordance with Test Method D471.Aspecimen0.075 by 1 by 2 in. (1.9 by 25 by 50 mm) shall be immersed indistilled water at 158 6 3.6F (70 6 2C) for 7 days. Afterseven days the specimen shall be removed, the surface mois-ture b

35、lotted and the specimen weighed. The percent gain shallbe determined by the following equation:WF 2 WO!WO100where:WF = weight of specimen after immersion for 7 days, andWO = dry weight of specimen before immersion.10.1.6 Chemical ResistanceSamples shall be aged for 48hat746 3.6F (23 6 2C) using solu

36、tions of 1N sulfuric acidand 1N hydrochloric acid. See Test Method D543.10.1.7 Tear StrengthThe gasket material shall be tested inaccordance with Test Method D624, Die C.10.1.8 Compression Set/Stress RelaxationElastomericmaterials shall comply with the compression set requirementsof 10.1.8.1 or the

37、stress relaxation requirements of 10.1.8.2.10.1.8.1 The gasket material shall be tested for compressionset in accordance with Test Method D395, Method B. Speci-mens shall be oven aged for 22 h at 70 6 1C (158 6 2F).10.1.8.2 The gasket material shall be tested for stressrelaxation in accordance with

38、Test Method D6147, usingMethod B and test specimen as defined in 7.1.2 of D6147. Thetest temperature and duration shall be 168 h at 23 6 2C (736 4F).10.2 Clamp Assembly Performance :10.2.1 Torque ResistanceClamp assemblies, tensionbands and tightening mechanisms shall be tested to withstandthe manuf

39、acturers required installation torque or a minimum of60 in.-lb (8.5 N-m) of applied torque without visible signs offailure. The band shall be tested over a steel mandrel of theappropriate coupling diameter and torqued as required.10.2.2 The maximum free running torque of stainless steeltension bands

40、 shall be 4 in.-lb (0.45 N-m). Stainless steeltension bands with torque resistance in excess of 100 in.-lbshall have a maximum free running torque of 8 in.-lb.10.2.3 Test Procedure for Free Running Torque:10.2.3.1 With the nonstressed clamp hand held and theslotted band fully engaged, the screw shal

41、l be rotated clock-wise 10 revolutions with the maximum value of the torquemeter recorded.10.2.3.2 The equipment required shall be a hand held torquemeter witha0to15in.-lb range.10.3 Coupling Performance Requirements:10.3.1 Deflection Sealing Resistance The joint shall havesufficient flexibility to

42、permit deflection in any direction asdefined by Table 2 and shall show no visible leakage when sodeflected while under an internal hydrostatic pressure of 4.3 psi(30 kPa) for a period of 15 min. The ends of the test pipe shallbe restrained only by an amount necessary to prevent longitu-dinal movemen

43、t. The deflection shall be measured as thedistance the free end of the one pipe has moved away from thecenter line of the fixed pipe. See Fig. 1.10.3.1.1 Assemble each coupling tested in accordance withthe manufacturers instructions between two sections of ran-domly selected pipe, not to exceed 5 ft

44、 in length, manufacturedto appropriate standards for the type of pipe the couplings areexpected to join.10.3.1.2 Support one pipe section on two blocks, one nearthe uncoupled end of the pipe section and the other blockimmediately adjacent to the coupling. Firmly restrain pipesection one.10.3.1.3 Def

45、lect the second pipe section in any direction anamount equal to the distance specified in Table 2 of thisstandard. Firmly restrain pipe section two.10.3.1.4 Plug the outbound pipe ends. Fill the assemblywith water expelling all air. Gradually apply the 4.3 psi internalhydrostatic pressure and mainta

46、in for 15 min.10.3.2 Shear Loading Resistance (Type B CouplingsOnly)The joint shall have sufficient resistance to shearloading to meet the requirements of the following test.10.3.2.1 Support two joined lengths of randomly selectedpipe on blocks, a minimum of 1 in. (38.1 mm) high, at threelocations.

47、One length shall be a minimum of 24 in. (609.6 mm)in length, supported on blocks, one near the uncoupled end,and the other immediately adjacent to the coupling. Firmlyrestrain this length in position as shown in Fig. 2. The othercoupled length shall be a minimum of 5 ft (1.52 m) in lengthand support

48、ed by a single block 6 in. (152.4 mm) from the endof the pipe.10.3.2.2 Fill the assembly with water and expel all air.Apply a load of 50 lb per in. (22.7 kg) of nominal diameter ata point 6 in. (152.4 mm) from the edge of the coupling upon a12 in. (304.8 mm) length of 3 by 3 in. (76.2 by 76.2 mm) an

49、gleiron or load distribution pad located on the top of the pipeimmediately adjacent to the coupling of the pipe having oneTABLE 2 RequirementsDeflection per Foot of Pipe LengthANominal ID,in. (mm)Deflection in./linear ft(mm/linear m)212 (50300)12 (42)1524 (375600)38 (31)2736 (675900)14 (21)3942 (9751050)316 (15)ASee 10.3.1.C1173 10 (2014)3support only. Under this loading there shall be no visibleleakage or displacement of more than 3/8 in. (9.53 mm) fromtrue alignment adjacent to the coupling, whe