ASTM C1172-2009e1 Standard Specification for Laminated Architectural Flat Glass《建筑用夹层平板玻璃的标准规格》.pdf
《ASTM C1172-2009e1 Standard Specification for Laminated Architectural Flat Glass《建筑用夹层平板玻璃的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM C1172-2009e1 Standard Specification for Laminated Architectural Flat Glass《建筑用夹层平板玻璃的标准规格》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1172 091Standard Specification forLaminated Architectural Flat Glass1This standard is issued under the fixed designation C1172; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in pa
2、rentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorial changes were made throughout in March 2011.1. Scope1.1 This specification covers the quality requirements of flatlaminated glass consisting of t
3、wo or more lites of glass bondedwith an interlayer material for use in building glazing.1.2 Depending on the number, thickness and treatment oflites, and the number and thickness of interlayers, the glassshall be laminated for applications including but not limited tosafety security, detention, hurr
4、icane/cyclic-wind resistant, blastresistant, bullet resistant and sound reduction glazing applica-tions. Laminated glass used in furniture applications is notincluded in this specification.1.3 Optical distortion and the evaluation thereof are notcurrently within the scope of the standard. Mockups ar
5、erecommended as a method to evaluate glass. (See AppendixX1.)1.4 The dimensional values, except thickness designations,stated in inch-pound units are to be regarded as the standard.The values in parentheses are for information only.1.5 The following safety hazards caveat pertains only to thetest met
6、hod portion, Section 7, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory l
7、imita-tions prior to use.2. Referenced Documents2.1 Reference to these documents shall be the latest revisionunless otherwise specified by the authority applying thisspecification.2.2 ASTM Standards:2C162 Terminology of Glass and Glass ProductsC1036 Specification for Flat GlassC1048 Specification fo
8、r Heat-Treated Flat GlassKind HS,Kind FT Coated and Uncoated GlassC1376 Specification for Pyrolytic and Vacuum DepositionCoatings on Flat GlassC1422 Specification for Chemically Strengthened FlatGlassC1503 Specification for Silvered Flat Glass MirrorE308 Practice for Computing the Colors of Objects
9、byUsing the CIE SystemE1886 Test Method for Performance of Exterior Windows,Curtain Walls, Doors, and Impact Protective SystemsImpacted by Missile(s) and Exposed to Cyclic PressureDifferentialsE1996 Specification for Performance of Exterior Windows,Curtain Walls, Doors, and Impact Protective Systems
10、Impacted by Windborne Debris in HurricanesF1233 Test Method for Security Glazing Materials AndSystemsF1642 Test Method for Glazing and Glazing Systems Sub-ject to Airblast LoadingsF1915 Test Methods for Glazing for Detention Facilities2.3 ANSI Standard:Z97.1 Safety Glazing Materials Used in Building
11、sSafetyPerformance Specifications and Methods of Tests32.4 Federal Document:4CPSC 16CFR1201 Consumer Product Safety CommissionSafety Standard for Architectural Glazing Materials2.5 National Institute of Justice (NIJ) Standard:5NIJ 0108.1 Ballistic Resistant Protective Materials2.6 UL Standards:6UL 7
12、52 Standard for Bullet Resisting Materials1This specification is under the jurisdiction of ASTM Committee C14 on Glassand Glass Products and is the direct responsibility of Subcommittee C14.08 on FlatGlass.Current edition approved May 1, 2009. Published June 2009. Originallyapproved 1991. Last previ
13、ous edition approved 2003 as C1172 03. DOI: 10.1520/C1172-09E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM websi
14、te.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from U.S. Consumer Product Safety Commission (CPSC), 4330 EastWest Hwy., Bethesda, MD 20814, http:/www.cpsc.gov.5Available from National Institute of Justice (
15、NIJ), 810 7th St., NW, Washing-ton, DC 20531, http:/www.ojp.usdoj.gov/nij.6Available from Underwriters Laboratories (UL), 333 Pfingsten Rd., North-brook, IL 60062-2096, http:/.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.UL 972 St
16、andard for Burglary Resisting Glazing Materials3. Terminology3.1 DefinitionsRefer to Terminology C162, SpecificationsC1036 or C1048, as appropriate.3.1.1 blemishes in flat glassRefer to Specifications C1036or C1048, as appropriate.3.2 Definitions of Terms Specific to This Standard:3.2.1 adhesion chi
17、psSee fuse.3.2.2 blow-ina separation of glass and interlayer at orclose to the laminate edge caused by penetration of theautoclaving medium into the edge during manufacturing.3.2.3 boil (bubble)a gas pocket in the interlayer materialor between the glass and interlayer.3.2.4 covered edgethe periphera
18、l area of the laminatecovered by the channel or sash when installed.3.2.5 delaminationa condition in which one or two of thelites of glass loses the bond between the glass lite and theinterlayer.3.2.6 discolorationa visibly noticeable color change(from original) in the appearance of a material.3.2.7
19、 distortionthe inability to see an image clearly; theimage is twisted out of natural shape.3.2.8 edge boilSee boil (bubble).3.2.9 exposed edgethe peripheral area of the laminateexposed to the environment after installation.3.2.10 fusea glass particle or crystalline material that ispermanently bonded
20、 to a surface of a lite.3.2.11 haira slender, pigmented filament from human oranimal epidermis or other thread-like filament.3.2.12 inside dirtforeign material trapped inside the lami-nate.3.2.13 interlayera layer or multiple layers of materialacting as an adhesive between lites of glass which addsa
21、dditional performance to the finished product, for example,impact resistance, solar control, acoustical insulation.3.2.14 laminated glassan assembly consisting of two ormore lites of glass, conforming to Specification C1036 orC1048 that are bonded together by interlayer material.3.2.15 lintshort fib
22、ers of yarn or fabric trapped within thelaminate.3.2.16 lite or lighta panel or sheet of glass or a panel orsheet of laminated glass.3.2.17 mismatchmisalignment of the edges of two lites ofglass, when laminated.3.2.18 nonsymmetricala term used to describe the con-struction of a laminate comprised of
23、 different glass types orthickness, or both.3.2.19 offsetglass lites that are intentionally not aligned ina laminate.3.2.20 rubabrasion of a glass surface producing a frostedappearance. Also known as a scuff.3.2.21 separationan area of the laminate that has becomedelaminated (see delamination).3.2.2
24、2 shineran area on a glass edge that has not beenground or polished.3.2.23 short interlayera condition of the laminate inwhich the interlayer does not extend to the edge.3.2.24 streaka noticeably visible directional blemish ordiscoloration on or in the laminated unit.3.2.25 symmetricala term used to
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC11722009E1STANDARDSPECIFICATIONFORLAMINATEDARCHITECTURALFLATGLASS 建筑 夹层 平板玻璃 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-463616.html