FORD WSS-M4C123-A-2007 GASOLINE UNLEADED SPARK PLUG ANTI-FOULING - TO BE USED WITH FORD WSS-M99P1111-A 《具有火花塞防污作用的无铅汽油 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSS-M4C123-A-2007 GASOLINE UNLEADED SPARK PLUG ANTI-FOULING - TO BE USED WITH FORD WSS-M99P1111-A 《具有火花塞防污作用的无铅汽油 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M4C123-A-2007 GASOLINE UNLEADED SPARK PLUG ANTI-FOULING - TO BE USED WITH FORD WSS-M99P1111-A 《具有火花塞防污作用的无铅汽油 与标准FORD WSS-M99P1111-A一起使用 》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2007 03 09 Revised Reduce benzene, incr ox stab; Deleted 3.16; Revised 1., 3.6.2, 3.9 and 3.11 J. Bennett2004 09 10 Revised Allow use of ETBE, reduce min vapor press. (6560) J. Bennett 2001 08 27 Activated J. Bennett Printed copies are uncontr

2、olled Copyright 2007, Ford Global Technologies, LLC Page 1 of 4 GASOLINE, UNLEADED, SPARK PLUG ANTI-FOULING WSS-M4C123-A 1. SCOPE The material defined by this specification is a well refined gasoline which can contain permitted gasoline extenders. 2. APPLICATION This specification was released origi

3、nally for material used as initial fill fuel for vehicles designed to operate on unleaded gasoline in Europe. This material is not specifically intended for use in certification testing. It may be used for engine hot test, mileage accumulation or general fueling. 3. REQUIREMENTS Material specificati

4、on requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.3 OCTANE NUMBERS 3.3.1 Motor, min 85.0 (ISO

5、5163) 3.3.2 Research, min 95.0 (ISO 5164) 3.4 TOTAL SULPHUR, max 50 mg/kg (ISO 14596, ISO 8754, ISO 24260, IP 373) 3.5 METAL CONTENT 3.5.1 Lead, max 0.0030 g/L (ASTM D 3237) 3.5.2 Phosphorus, max 0.0010 g/L (ASTM D 3231) ENGINEERING MATERIAL SPECIFICATIONWSS-M4C123-A Printed copies are uncontrolled

6、Copyright 2007, Ford Global Technologies, LLC Page 2 of 4 3.6 COMPOSITION 3.6.1 Hydrocarbons (ASTM D 1319, IP 156, DIN 51 791, BS 2000: part 156: 1993) Aromatic, max 2.5% Olefins, max 30.0% Saturates Report 3.6.2 Benzene, max 0.1% (ASTM D 3606, EN 12177, EN 238) 3.6.3 Oxygenates (EN 1601, EN13132) M

7、TBE/ETBE, max 15.0% Other oxygenates 0.5% 3.6.4 Water and Sediment, max 0.010% (ASTM D 2709) 3.6.5 Gum, washed, max 4 mg/100 mL (ISO 6246) 3.7 DISTILLATION RANGE (ASTM D 86/ISO 3405) 10% Volume evaporated at, max 65 C 50% Volume evaporated at, max 105 C 90% Volume evaporated at, max 160 C Final boil

8、ing point, max 200 C 3.8 VAPOR PRESSURE 60.00 - 85.00 kPa (ISO 3007, EN 13016-1) 3.9 OXIDATION STABILITY, min 900 minutes (ASTM D 525, IP 40, ISO 7536, DIN 51780 BS 2000: Part 40: 1992) 3.10 COPPER CORROSION, max 1 a (ISO 2160, 3 h, 50 C) 3.11 ADDITIVES The material may contain normal commercial add

9、itives, e.g., deicers, detergents, etc., at concentrations representative of good commercial practice in the receiving locale (unless otherwise specified). ENGINEERING MATERIAL SPECIFICATIONWSS-M4C123-A Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 3 of 4 3.12 SP

10、ARK PLUG ANTI-FOUL Spark plug anti-fouling performance must be demonstrated by actual vehicle or engine test data supplied to the responsible Ford product engineering activity. The test procedure must be agreed upon between this activity and the supplier. 3.13 COLOR The material shall be dyed in acc

11、ordance with supplier standard practice to a color agreed with Ford Motor Company. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 FLAMMABILITY This material represents a potential fire hazard. The

12、 Manufacturing Engineering Department or other responsible activity shall notify both the Security and Safety Units of its presence to assure that proper fire precautions are provided. The location in which it is used or stored shall be included in the notifications. 5.2 SAMPLING AND SUBMISSION OF S

13、AMPLES (ISO 3170/3171, ASTM D 4057/D 4177) Quality Control records must be made available to Fuels and Lubricants Engineering upon request. ENGINEERING MATERIAL SPECIFICATIONWSS-M4C123-A Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 4 of 4 Volatility Grade _ Date

14、 _ Company _ Refinery Location _ Specification _ Actual Test Results ISO ASTM (Typical) Manuf. Limits Research Octane 5164 D 2699 _ _ Motor Octane 5163 D 2700 _ _ Lead, g/L, D 3237 _ _ Manganese, g/L as MMT D 3831 _ _ Phosphorus, g/L D 3231 _ _ Total Sulfur, % 14596 D 4294 Copper Corrosion 2160 D 13

15、0 _ _ Oxidation Stability 7536 D 525 _ _ Reid Vapor Pres., kPa 3007 D 323 _ _ Benzene D 3606 _ _ Distillation Range 3405 D 86 _ _ Initial Boiling Point, C _ _ 10 % Evaporated, _ _ 50 % Evaporated, C _ _ 90 % Evaporated, _ _ End Point, C _ _ Oxygenates D 4815 _ _ Acidity of Residue D 1093 _ _ Vapor-L

16、iq. Ratio D 2533 _ _ Hydrocarbons D 1319 _ _ Aromatics, % _ _ Olefins, _ _ Saturates, % _ _ Gum, mg/100 mL washed 6246 D 381 _ _ Gum, mg/100 mL unwashed 6246 D 381 _ _ Water and Sediment, % D 2709 _ _ Density at 15 C 3675 D 1298 _ _ Calorific Value D 240 _ _ Carbon, Hydrogen, Oxygen _ _ Additives Type & Formula Manuf. Limits Anti-oxidant _ _ Combustion Additive _ _ De-icer _ _ Detergent _ _ Dispersant _ _ Metal Deactivator _ _ Upper Cylinder Lubricant _ _ Dye _ _ Miscellaneous _ _ Signature _ Title _