FORD WSP-M4G347-A1-2014 SEALER POLYACRYLATE LATEX BASE RADIAL OIL SEALS TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSP-M4G347-A1-2014 SEALER POLYACRYLATE LATEX BASE RADIAL OIL SEALS TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSP-M4G347-A1-2014 SEALER POLYACRYLATE LATEX BASE RADIAL OIL SEALS TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Action Changes1992 11 16 NT00E10254964000 Released T. KochWP 3948-a Page 1 of 3 SEALER, POLYACRYLATE LATEX BASE, RADIAL OIL WSP-M4G347-A1SEALS WSP-M4G347-A21. SCOPEThe material defined by this specification is a polyacrylate l

2、atex based,water borne, paint type sealer.2. APPLICATIONThis specification was released originally for material applied by sealsuppliers to the O.D. of oil seals to ultimately provide an oil tight sealbetween the oil seal O.D. and the housing bore of rear wheel bearingassemblies and transmission rad

3、ial oil seal assemblies.3. REQUIREMENTS3.1 STATISTICAL PROCESSSuppliers must conform to the requirements of Ford Quality SystemStandard Q-101. A mutually acceptable Control Plan as describedtherein is required for material/source approval. Appropriatestatistical tools must be used to analyze process

4、/product data sothat variation in the final product is continuously reduced.3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSISFord Motor Company, at its option, may conduct infrared and/orthermal analysis of material/parts supplied to this specification.The IR spectra and thermograms established

5、 for initial approval shallconstitute the reference standard and shall be kept on file at thedesignated material laboratory. All samples shall produce IR spectraand thermograms that correspond to the reference standard when testedunder the same conditions.3.3 CONDITIONING AND TEST CONDITIONSAll test

6、 values indicated herein are based on material conditioned ina controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relativehumidity for not less than 24 h prior to testing and tested under thesame conditions unless otherwise specified.3.4 CLEANINGSurfaces to be coated shall be cleaned free from greas

7、e, oil, rustand/or other foreign materials and shall be thoroughly dry beforecoating is applied.NOT TO BE USED FOR NEW DESIGN2014 N Status No replacment named L. Sinclair, NAENGINEERING MATERIAL SPECIFICATIONWSP-M4G347-A1WSP-M4G347-A2WP 3948-b Page 2 of 3 3.5 MODE OF APPLICATIONMay be applied electr

8、ostatically or sprayed by t he seal suppliers. Itshall be non-tacky on the seals prior to packaging and shipping tothe using location.3.6 MIXTURE A1 A23.6.1 Viscosity at 27 C, mPa.s 20 - 25 20 - 25(ASTM D 3794,2196 Method A, 50 rpm)3.7 TOTAL SOLIDS, % 30 - 40 30 - 40(ASTM D 2834, except heat at102 +

9、/- 3 C for 3 h or untilsample reaches constantweight)3.8 DRYING TIME AT 23 +/- 2 C (A1 & A2) Tack free in 30minutes3.9 COLOR Red Yellow3.10 SPECIFIC GRAVITY at 27 C 0.9 - 1.3 0.9 - 1.3(ASTM D 891, Method “B“)3.11 FILM THICKNESSShall b e as specified on the engineering drawings. Film thicknessshall b

10、e determined by measuring the O.D. of the seal in 4 positionsas received and then remeasuring in the same loc ations after removingthe coating with a suitable solvent.3.12 ADHESION OF COATINGCut an “X“ in the coate d surface to the metal in several places witha razor blad e. Press scotch tape onto t

11、he area firmly. After 5minutes, remove the tap e, pulling at a direct tangent to the outsidediam eter of the seal. Regardless of the rate of tape removal, nocoating shall adhere to the tape.3.13 FLAKING OR POWDERINGScrape the coated surface until clean metal appears. The scrapingsshall be free from

12、flakes or powder.3.14 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inal l characteristics to the material upon which approval wasoriginally granted.ENGINEERING MATERIAL SPECIFICATIONWSP-M4G347-A1WSP-M4G347-A2WP 3948-b Page 3 of 3 Pri or to making any change

13、 in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affect the materials ability to meet the specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected

14、 Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, t est samples and a new code identification areto be submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials ad

15、dressed by this document. The restrictions aredefined in Engineering Material Specification WSS-M99P9999-A1.4. APPROVAL OF MATERIALSMat erials defined by this specification must have prior approval by theresponsible Materials Engineeri ng activity. Suppliers desiring approval ofthe ir materials shal

16、l first obtain an expression of interest from theaffec ted Purchasing, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity a completed copy of their laboratory test reports, signed by aqualified and authorized representative

17、 of the test faci lity, demonstratingful l compliance with all the requirements of this specification (testresults, not nominal values), the material designation a nd code number, andtes t specimens for Ford evaluation. Fords engineering approval of amateri al will be based on its performance to thi

18、s specification and on anassessment of suitability for i ntended processes and/or applications. Uponapprov al, the material will be added to the Engineering Material ApprovedSource List.5. GENERAL INFORMATIONThe information below is provided for clarification and assistance inmeeting the requirements of this specification.5.1 FLASH POINT, min 93 C(ASTM D 56)