FORD WSF-M4D881-A-2008 ABS MOLDING COMPOUND CLEAR INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯透明模塑料 内部用(和FORD WSS-M99P1111-A一起使用)(使用 FORD WSK-M4D827-A FORD WSK-M4D82.pdf
《FORD WSF-M4D881-A-2008 ABS MOLDING COMPOUND CLEAR INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯透明模塑料 内部用(和FORD WSS-M99P1111-A一起使用)(使用 FORD WSK-M4D827-A FORD WSK-M4D82.pdf》由会员分享,可在线阅读,更多相关《FORD WSF-M4D881-A-2008 ABS MOLDING COMPOUND CLEAR INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯透明模塑料 内部用(和FORD WSS-M99P1111-A一起使用)(使用 FORD WSK-M4D827-A FORD WSK-M4D82.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Ver. 3 2008 08 20 N-STATUS Replaced by WSK-M4D827-A C. Boese, FNA 2006 05 24 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.10, 3.11 & 4 1994 02 28 Released NGA1E10370437002 A. Vallabhanath Printed copies are uncontrolled Copyright 2008, Ford
2、 Global Technologies, LLC Page 1 of 5 ABS MOLDING COMPOUND, CLEAR, INTERIOR WSF-M4D881-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a clear molding compound based on acrylonitrile/butadiene/styrene. 2. APPLICATION This specification was released originally f
3、or material used for visible interior parts, such as integrated control panel button with inmold decoration. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1
4、111-A). 3.1.1 All requirements of this specification, identified by symbol(s), shall be met with data representing 3 sigma values. 3.4 MOLDING COMPOUND (s) 3.4.1 Melt Flow Rate 1.0 - 3.6 g/10 minutes (ISO 1133/ASTM D 1238, 220 C, 10 kg) The material shall be dried for min of 2 h at 80 - 85 C in a me
5、chanical convection oven immediately preceding the test. 3.5 MOLDED TEST SPECIMEN 3.5.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test specimens. The following dimensions are required: A. 150 min x 10 x 4.0 +/- 0.2 mm (T
6、ensile Bar, ISO 3167) B. 120 x 10 x 4.0 +/- 0.2 mm Specimens with shorter dimensions shall be cut from the centre portion of the test specimen A and/or B. The specimens shall be prepared according to ISO 294. No annealing allowed. ENGINEERING MATERIAL SPECIFICATION WSF-M4D881-A Printed copies are un
7、controlled Copyright 2008, Ford Global Technologies, LLC Page 2 of 5 3.5.2 Density 1.05 - 1.11 g/cm (ISO 1183, Method A) (s) 3.5.3 Tensile Strength at Yield, min 40 MPa (ISO R 527, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen, 50 mm/minute test speed) (s) 3.5.4 Flexural Modulus, min 1.8 GPa (ISO 178,
8、80 x 10 x 4.0 +/- 0.2 mm specimen, 64 mm support span) 3.5.5 Shear Modulus at 23 C 7.6 MPa (ASTM D 4065, forced constant amplitude, fixed frequency of 1 Hz +/- 15%, strain level below 1%. Specimen approx. 60 x 10 x 4.0 +/- 0.2 mm cut from the centre of specimen A. Specimen length between clamps 35-4
9、0 mm. Soak time at each temperature interval - 3 minutes minimum) Additionally, a Shear Modulus vs. Temperature curve shall be plotted for -50 to +160 C temperature range, at 5 C minimum intervals. The plotted curve must be within tolerance range shown on page 5. (s) 3.5.6 Impact Strength, Izod, min
10、 (ISO 180/1A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens for each test) 3.5.6.1 At 23 +/- 2 C 4.9 kJ/m 3.5.6.2 At -5 +/- 2 C 2.5 kJ/m 3.5.6.3 At -40 +/- 2 C 0.8 kJ/m The test specimens must be conditioned for minimum of 6 h at the above specified temperature prior to impact test. Low temperatur
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSFM4D881A2008ABSMOLDINGCOMPOUNDCLEARINTERIORTOBEUSEDWITHFORDWSSM99P1111A 丙烯腈 丁二烯 苯乙烯 透明 塑料 内部 FORDWSSM99P1111A

链接地址:http://www.mydoc123.com/p-750224.html