FORD ESP-M9H126-A-1988 SCREEN POLYESTER《聚酯网》.pdf

《FORD ESP-M9H126-A-1988 SCREEN POLYESTER《聚酯网》.pdf》由会员分享，可在线阅读，更多相关《FORD ESP-M9H126-A-1988 SCREEN POLYESTER《聚酯网》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Release/Revision1988 03 23 WR-161326-P ReleasedWP 3948-a Page 1 of 2SCREEN, POLYESTER ESP-M9H126-A1. SCOPEThe material defined by this specification is a woven screen usingpolyester thread with a nominal 100 micron

2、 mesh opening.2. APPLICATIONThis specification was released originally for filter material used forgovernor screen assemblies in automatic transmissions.3. REQUIREMENTS3.1 CONSTRUCTIONThe fabric shall be constructed in a half- leno pattern, in whichevery other warp thread is doubled. Where these dou

3、bled threadspass a filling thread, one passes over the filling thread and onepasses under the filling thread.3.2 CONDITIONING AND TEST CONDITIONSAll test values indicated herein are based on material conditionedin a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relativehumidity for not less tha

4、n 24 h prior to testing and tested underthe same conditions unless otherwise specified.3.3 SPECIFIC GRAVITY 1.36 - 1.40(ASTM D 792)3.4 MELTING POINT 250 - 260 C(FLTM BO 21-2)3.5 THREAD DIAMETERWarp 60 - 80 micrometres + 2 x 36 - 44 micrometresFill 44 - 52 micrometres3.6 MESH COUNTWarp Direction 56 -

5、 59/cmFill Direction 65 - 68/cm3.7 WEIGHT 39 - 43 g/m23.8 FABRIC THICKNESS 102 - 110 micrometres3.9 MESH OPENING 90 - 110 micrometresENGINEERING MATERIAL SPECIFICATION ESP-M9H126-A WP 3948-b Page 2 of 23.10 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSISFord Motor Company, at its option, may cond

6、uct infrared and/orthermal analysis of material/parts supplied to this specification.The IR spectra and thermograms established for initial approvalshall constitute the reference standard and shall be kept on fileat the designated material laboratory. All samples shall produceIR spectra and thermogr

7、ams that correspond to the referencestandard when tested under the same conditions.3.11 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inall characteristics to the material upon which approval wasoriginally granted.Prior to making any change in the properties

8、, composition,construction, color, processing or labeling of the materialoriginally approved under this specification, whether or not suchchanges affect the materials ability to meet the specificationrequirements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering

9、 activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, test samples and a new code identificationare to be submitted with the request.Substance restrictions imposed by law, regulations or Ford, applyto the materials addressed by this documen

10、t. The restrictions aredefined in Engineering Material Specification WSS-M99P9999-A1,unless a different suffix (e.g., A2 or A3) is specified on theengineering document for the application.4. APPROVAL OF MATERIALSMaterials defined by this specification must have prior approval by theresponsible Mater

11、ials Engineering activity. Suppliers desiring approvalof their materials shall first obtain an expression of interest from theaffected Purchasing, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity its own laboratory report to the specification (test results,not nominal values), the material designation and code number, and testspecimens for Ford evaluation. Upon approval, the material will be addedto the Engineering Material Approved Source List.