FORD ESE-M2D363-A-2009 FLUOROELASTOMER (FKM) HIGH TEMPERATURE RESISTANT - GASKET TO BE USED WITH FORD WSS-M99P1111-A 《垫片用耐高温氟橡胶（FKM） 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESE-M2D363-A-2009 FLUOROELASTOMER (FKM) HIGH TEMPERATURE RESISTANT - GASKET TO BE USED WITH FORD WSS-M99P1111-A 《垫片用耐高温氟橡胶（FKM） 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESE-M2D363-A-2009 FLUOROELASTOMER (FKM) HIGH TEMPERATURE RESISTANT - GASKET TO BE USED WITH FORD WSS-M99P1111-A 《垫片用耐高温氟橡胶（FKM） 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 08 26 N-STATUS No known use. No Replacement Named C. Mracna, NA 2004 09 13 Revised Para 3.0 inserted; para 3.1, 3.2, 3.3, 3.5 & 4 deleted 1986 08 27 Released CE3Q-RD836100E Printed copies are uncontrolled Copyright 2009, Ford Global Techn

2、ologies, LLC Page 1 of 2 FLUOROELASTOMER (FKM), HIGH TEMPERATURE ESE-M2D363-A RESISTANT - GASKET NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a low modulus, high elongation fluoroelastomer, with excellent oil and heat resistance, suitable for long-term, high t

3、emperature service conditions. 2. APPLICATION This specification was released originally for material used in the “best-in-class“ gasket for the rocker arm and oil pan, where high flange temperature resistance is required. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material s

4、uppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 MATERIAL TESTING 3.4.1 Preparation of Test Specimens All tests shall be performed on specimens die-cut from the molded parts or from molded ASTM test sheets, press cured for

5、10 minutes at 177 C and post cured for 16 h at 232 C. The ASTM test sheets shall have the following dimensions: 150 x 150 mm, min x 2.0 +/- 0.2 mm. Specimens taken from parts shall be cut as follows: . Tensile Strength according to ASTM D 412, die C, full thickness. If the length between the compres

6、sion limiters is not sufficient to accommodate die C, use a die exactly one-half the dimensions of the die C. . Tear Strength according to ASTM D 624, die B, full thickness. . Volume Change -25 mm x part width x part thickness. . Compression Set -25 mm long x part width x single thickness minus any

7、skirt. Do not buff any specimens, including those with a bead, except for Compression Set. ENGINEERING MATERIAL SPECIFICATIONESE-M2D363-APrinted copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 2 3.4.2 Original Properties Hardness, Durometer A 65 +/- 5 (ASTM D 2240, in

8、stantaneous) Tensile Strength, min 9.3 MPa (ASTM D 412, die C) Elongation, min 275% (ASTM D 412, die C) Modulus at 100% Elongation 1.8 - 3.0 MPa (ASTM D 412, die C) Tear Strength, min 20.0 kN/m (ASTM D 624, die B) 3.4.3 Compression Set, max 45% (ASTM D 395, Method B, 22 h, 225 +/- 2 C) 3.4.4 Oven Ag

9、ed (ASTM D 573, 168 h at 225 +/- 2 C) Hardness, Durometer A Change, max +10 Tensile Strength Change, max -10% Elongation Change, max -18% 3.4.5 Immersion in ASTM No. 1 Oil (ASTM D 471, 168 h at 150 +/- 2 C) Volume Change 0 to +5% 3.4.6 Immersion in ASTM No. 3 Oil (ASTM D 471, 168 h at 150 +/- 2 C) H

10、ardness, Durometer A Change, max -8 Tensile Strength Change, max -35% Elongation Change, max -30% Volume Change, max 0 to +8% 3.4.7 Flexibility at -40 C No cracks After heat aging (para 3.4.4), place specimens and mandrel in the cold box at -40 +/- 2 C for 24 h. Bend specimens 180 over 13 mm diameter mandrel.