FORD ESD-M4C103-A-2010 GASOLINE UNLEADED 95 RON 0 003 g L LEAD TO BE USED WITH FORD WSS-M99P1111-A 《含铅量95 RON 0 003 g L的无铅汽油 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESD-M4C103-A-2010 GASOLINE UNLEADED 95 RON 0 003 g L LEAD TO BE USED WITH FORD WSS-M99P1111-A 《含铅量95 RON 0 003 g L的无铅汽油 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESD-M4C103-A-2010 GASOLINE UNLEADED 95 RON 0 003 g L LEAD TO BE USED WITH FORD WSS-M99P1111-A 《含铅量95 RON 0 003 g L的无铅汽油 与标准FORD WSS-M99P1111-A一起使用 》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 01 06 N-STATUS No known use. No replacement named D. DiGregorio, NA 2004 06 21 Revised Para 3.0 inserted; para 3.1, 3.2, 3.17 & 4 deleted 1985 05 27 Released SM/342156TC Printed copies are uncontrolled Copyright 2010, Ford Global Technolo

2、gies, LLC Page 1 of 4 GASOLINE, UNLEADED, 95 RON 0.003 g/L LEAD ESD-M4C103-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a well refined gasoline containing normal commercial additives and which can contain permitted gasoline extenders. Additional anti-oxidant

3、 and additives to prevent spark plug fouling/corrosion may be present for some applications. 2. APPLICATION This specification was released originally for material used as initial fill fuel for vehicles designed to operate on unleaded gasoline in Europe. This material is not specifically intended fo

4、r use in certification testing. It may be used for engine hot test, mileage accumulation or general fueling. When used as an initial fill or hot test fuel the material must meet the additional requirements shown in 3.14. When used as a hot test fuel in locations where a proportion of engines may be

5、shipped or stored for periods in excess of six months before use, the material must meet the additional requirements shown in 3.15. Setubal plant See additional requirement 3.16 3. REQUIREMENTS This material must meet all pertinent requirements of EEC directive 85/210/EEC. 3.0 STANDARD REQUIREMENTS

6、FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.3 OCTANE NUMBERS 3.3.1 Motor, min 85.0 (ISO 5163) 3.3.2 Research, min 95.0 (ISO 5164) 3.4 TOTAL SULPHUR, max 0.040% (ASTM D 4294) 3.5 METAL C

7、ONTENT 3.5.1 Lead, max 0.0030 g/L (ASTM D 3237) ENGINEERING MATERIAL SPECIFICATIONESD-M4C103-APrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 4 3.5.2 Phosphorus, max 0.0010 g/L (ASTM D 3231) 3.6 COMPOSITION 3.6.1 Hydrocarbons (ASTM D 1319, IP 156, DIN 51 791,

8、BS 2000: part 156: 1993) Aromatic, max 50.0% Olefins, max 10.0% Saturates Report 3.6.2 Benzene, max 5.0% (ASTM D 3606) 3.6.3 Oxygenates Report (ASTM D 4815) 3.6.4 Water and Sediment, max 0.010% (ASTM D 2709) 3.6.5 Gum, washed, max 5 mg/100 mL (ISO 6246) 3.7 DISTILLATION RANGE (ISO 3405) 10% recovere

9、d at 30.0 - 60.0 C 50% recovered at 80.0 - 110.0 C 90% recovered at 140.0 - 190.0 C Final boiling point, max 215.0 C 3.8 FUEL VOLATILITY 60.00 - 90.00 (ISO 3007) kPa 3.9 OXIDATION STABILITY, min 240 m (ASTM D 525, IP 40, DIN 51 780, BS 2000: Part 40: 1992) 3.10 COPPER CORROSION, max 1 b (ISO 2160, 3

10、 h, 50 C) 3.11 ODOR The material shall have the usual characteristic odor of gasoline. There shall be no obvious foreign odors. ENGINEERING MATERIAL SPECIFICATIONESD-M4C103-APrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 4 3.12 ADDITIVES The material shall co

11、ntain normal commercial additives, e.g., deicers, detergents, etc., at concentrations representative of good commercial practice in the receiving locale (unless otherwise specified). The additive package shall be formulated for a “clean-up“ level of detergency for control of deposits in electronic f

12、uel injectors, as well as a “keep-clean“ level of detergency for the entire induction system, including intake valves. This level of performance must be demonstrated by actual vehicle or engine test data supplied to the responsible Ford product engineering activity. The test procedure must be agreed

13、 upon between this activity and the supplier. 3.13 COLOR The material shall be dyed in accordance with supplier standard practice to a color agreed with Ford Motor Company. 3.14 ADDITIONAL REQUIREMENT FOR INITIAL FILL AND HOT TEST Spark plug anti-fouling/anti-corrosion additive ESD-M99C118-A must be

14、 added at 0.50% +/- 0.10% by volume. This addition may be performed by the fuel supplier or by the Ford location concerned. 3.15 ADDITIONAL REQUIREMENT FOR LONG TERM ENGINE STORAGE Oxidation Stability, minimum 600 minutes (ASTM D 525, IP 40, DIN 51780, BS 2000: Part 40: 1992) To achieve this require

15、ment, anti-oxidant SS-M99C9103-A may be added in the following proportions: 44 mL per 1,000 L 3.16 ADDITIONAL REQUIREMENT FOR SETUBAL PLANT The material must comply with Volkswagen material specification VW TL 521,0 38, type X. 5. GENERAL INFORMATION The information given below is provided for clari

16、fication and assistance in meeting the requirements of this specification. 5.1 FLAMMABILITY This material represents a potential fire hazard. The Manufacturing Engineering Department or other responsible activity shall notify both the Security and Safety Units of its presence to assure that proper f

17、ire precautions are provided. The location in which it is used or stored shall be included in the notifications. 5.2 SAMPLING AND SUBMISSION OF SAMPLES (ISO 3170/3171) 5.3 Quality Control records must be made available to the responsible product engineering office upon request. ENGINEERING MATERIAL

18、SPECIFICATIONESD-M4C103-APrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 4 Volatility Grade_ Date_ Company_ Refinery Location_ Specification_ Actual Test Results ISO ASTM (Typical) Manuf. Limits Research Octane 5164 D 2699 _ _ Motor Octane 5163 D 2700 _ _ Lead

19、, g/L, D 3237 _ _ Manganese, g/L as MMT D 3831 _ _ Phosphorus, g/L D 3231 _ _ Total Sulfur, % 2192 D 4294 Copper Corrosion 2160 D 130 _ _ Oxidation Stability D 525 _ _ Reid Vapor Pres., kPa 3007 D 323 _ _ Benzene D 3606 _ _ Distillation Range 3405 D 86 _ _ Initial Boiling Point, C _ _ 10% Evaporated

20、, C _ _ 50% Evaporated, C _ _ 90% Evaporated, C _ _ End Point, C _ _ Oxygenates D 4815 _ _ Acidity of Residue D 1093 _ _ Vapor-Liq. Ratio D 2533 _ Hydrocarbons D 1319 _ _ Aromatics, % _ _ Olefins, % _ _ Saturates, % _ _ Gum, mg/100 mL washed 6246 D 381 _ _ Gum, mg/100 mL unwashed 6246 D 381 _ _ Wate

21、r and Sediment, % D 2709 _ _ Sp. g. at 15 C 3675 D 1298 _ _ Calorific Value D 240 _ _ Carbon, Hydrogen, Oxygen _ _ Additives Type & Formula Manuf. Limits Anti-oxidant _ _ Combustion Additive _ _ De-icer _ _ Detergent _ _ Dispersant _ _ Metal Deactivator _ _ Upper Cylinder Lubricant _ _ Dye _ _ Miscellaneous _ _ Signature_ Title_