FORD ESB-M15P30-A-2009 ORNAMENT ASSEMBLY EXTERIOR - ADHESIVE BONDED TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用胶粘剂粘合的装饰组件 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M2P191-A1 FORD .pdf

《FORD ESB-M15P30-A-2009 ORNAMENT ASSEMBLY EXTERIOR - ADHESIVE BONDED TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用胶粘剂粘合的装饰组件 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M2P191-A1 FORD .pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M15P30-A-2009 ORNAMENT ASSEMBLY EXTERIOR - ADHESIVE BONDED TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用胶粘剂粘合的装饰组件 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M2P191-A1 FORD .pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2009 02 04 N-STATUS Replaced by WSS-M2P191-A1/A2 C. McComb, FNA 2000 11 29 Revised Updated A. Cockman 1988 02 04 Released CAR1-PR192283 Printed copies are uncontrolled Page 1 of 5 Copyright 2009, Ford Global

2、 Technologies, Inc. ORNAMENT ASSEMBLY, EXTERIOR - ADHESIVE BONDED ESB-M15P30-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE This specification defines the performance requirements for ornaments usually consisting of a bezel and a decorated insert. 2. APPLICATION These performance requirements were release

3、d originally for exterior body ornaments having a jewelry appearance. Various decorative materials can be utilized to obtain the desired styling effects. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Materia

4、l suppliers and part producers must conform to the Companys Quality System Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material lab

5、oratory. All samples shall produce IR spectra and thermograms that correspond to the reference standard when tested under the same conditions. 3.3 APPEARANCE Shall match the approved Styling master. 3.4 ADHESION No delamination of layers or insert(s) from the bezel is permitted after exposure to any

6、 resistance test in this specification. ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 2 of 5 Copyright 2009, Ford Global Technologies, Inc. 3.5 CYCLE TESTS Test Acceptance Criteria for para 3.5.1 and para 3.5.2: There shall be no green, red or white corrosion on frontal or perpendicular surfa

7、ces or runout to these surfaces from side recessed surfaces. No delamination of layers or insert(s) from the bezel is permitted. No evidence of crazing, checking, warping or other surface degradation. 3.5.1 FULLY DECORATED INSERTS UNASSEMBLED AT LEASE FIVE DECORATED INSERTS WILL BE TESTED IN THE FOL

8、LOWING SEQUENCE: Water Resistance 96 h (FLTM BI 4-1) Salt Spray Resistance 240 h (FLTM BI 3-1) Humidity Aging 240 h (ASTM D 2247) Thermal Cycle - C.A.S.S. 10 cycles (see para 5.1) Thermal Shock 1 cycle (see para 5.2) 3.5.2 FULLY ASSEMBLED INSERTS AND BEZELS AT LEAST FIVE ORNAMENT ASSEMBLIES WILL BE

9、TESTED IN THE FOLLOWING SEQUENCE: Water Resistance 144 h (FLTM BI 4-1) Salt Spray Resistance 96 h (FLTM BI 3-1) ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 3 of 5 Copyright 2009, Ford Global Technologies, Inc. Humidity Aging 144 h (ASTM D 2247) Thermal Cycle - C.A.S.S. 5 cycles (see para 5.

10、1) Thermal Shock 1 cycle (see para 5.2) 3.6 WEATHERING RESISTANCE Expose samples per one of the following: 3.6.1 Carbon - Arc Weatherometer 1600 h (FLTM BO 1-1) 3.6.2 Fluorescent UV - 1600 h Condensation Apparatus (ASTM G-53-84) Operate the apparatus to maintain the following conditions: Cycle - 4 h

11、 UV exposure at 60 C followed by 4 h condensing humidity at 50 C. 3.6.3 Xenon - Arc Weatherometer 1000 h (ASTM G-26-84) Method 2 Operate the apparatus to maintain the following conditions: Light Cycle Dark Cycle Irradiance 0.55w/m2 - Black Panel Temperature 70 +/- 3 C 38 +/- 2 C Dry Bulb Temperature

12、 63 +/- 4 C 38 +/- 2 C Relative Humidity 50 +/- 10 % 100 +/- 10 % Conditioning Water 63 +/- 4 C 40 +/- 4 C Following exposure there shall be: No evidence of crazing, checking, warping or other surface degradation. No greater degree of fading, dulling or chalking of subsurface colors than that exhibi

13、ted by the sample originally approved by the affected Product Engineering office. Blotchy or streaky appearance shall be considered failure. ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 4 of 5 Copyright 2009, Ford Global Technologies, Inc. 3.7 FLORIDA EXPOSURE (For Initial Qualification) Aft

14、er 12 months minimum exposure at 5 facing south in the Miami, Florida area, there shall be: No evidence of crazing, checking, warping or other surface degradation. No greater degree of fading, dulling, or chalking of subsurface colors than that exhibited by the sample originally approved by the affe

15、cted Product Engineering office. Blotchy or streaky appearance shall be considered failure. 3.8 SAMPLING Acceptance testing for conformance to Thermal Cycle - Corrosion (para 3.5) and Weathering Resistance (para 3.6) will be run at the frequency specified in Appendix D of Q-101. Suppliers achieving

16、the Q1 rating will be made exempt from this requirement. 3.9 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved und

17、er this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notification of the Company, further instructio

18、ns will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identifi

19、ed in Restricted Substance Management Standard WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to the Company must have prior approval. Certain materials subcontracted by part suppliers may also require prior approval. These include materials criti

20、cal to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplie

21、r shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification. ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 5 of 5 Copyright 2009, Ford

22、Global Technologies, Inc. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 THERMAL CYCLE - C.A.S.S. - TEST SEQUENCE 82 +/- 3 C for 2 h 23 +/- 2 C for 1 h -34 +/- 1 C for 2 h 23 +/- 2 C for 1 h 16 h

23、C.A.S.S. test per FLTM BQ 5-1 1 h rinse and dry then examine. 5.2 THERMAL SHOCK - TEST SEQUENCE Method 1 (refer to FLTM BI 7-3) 4 h water immersion 4 h minimum exposure at -30 +/- 1 C Direct steam blast on scribed X at 45 angle 50 mm - 75 mm from panel for 15 s minimum Method 2 Place one ornament/insert in sufficient deionized water to cover completely. Freeze for four (4) hours at -30 C. Place ice block/insert into large container of hot (50 C) water.