欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESB-M15P30-A-2009 ORNAMENT ASSEMBLY EXTERIOR - ADHESIVE BONDED TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用胶粘剂粘合的装饰组件 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M2P191-A1 FORD .pdf

    • 资源ID:745084       资源大小:33.25KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESB-M15P30-A-2009 ORNAMENT ASSEMBLY EXTERIOR - ADHESIVE BONDED TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用胶粘剂粘合的装饰组件 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M2P191-A1 FORD .pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2009 02 04 N-STATUS Replaced by WSS-M2P191-A1/A2 C. McComb, FNA 2000 11 29 Revised Updated A. Cockman 1988 02 04 Released CAR1-PR192283 Printed copies are uncontrolled Page 1 of 5 Copyright 2009, Ford Global

    2、 Technologies, Inc. ORNAMENT ASSEMBLY, EXTERIOR - ADHESIVE BONDED ESB-M15P30-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE This specification defines the performance requirements for ornaments usually consisting of a bezel and a decorated insert. 2. APPLICATION These performance requirements were release

    3、d originally for exterior body ornaments having a jewelry appearance. Various decorative materials can be utilized to obtain the desired styling effects. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Materia

    4、l suppliers and part producers must conform to the Companys Quality System Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material lab

    5、oratory. All samples shall produce IR spectra and thermograms that correspond to the reference standard when tested under the same conditions. 3.3 APPEARANCE Shall match the approved Styling master. 3.4 ADHESION No delamination of layers or insert(s) from the bezel is permitted after exposure to any

    6、 resistance test in this specification. ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 2 of 5 Copyright 2009, Ford Global Technologies, Inc. 3.5 CYCLE TESTS Test Acceptance Criteria for para 3.5.1 and para 3.5.2: There shall be no green, red or white corrosion on frontal or perpendicular surfa

    7、ces or runout to these surfaces from side recessed surfaces. No delamination of layers or insert(s) from the bezel is permitted. No evidence of crazing, checking, warping or other surface degradation. 3.5.1 FULLY DECORATED INSERTS UNASSEMBLED AT LEASE FIVE DECORATED INSERTS WILL BE TESTED IN THE FOL

    8、LOWING SEQUENCE: Water Resistance 96 h (FLTM BI 4-1) Salt Spray Resistance 240 h (FLTM BI 3-1) Humidity Aging 240 h (ASTM D 2247) Thermal Cycle - C.A.S.S. 10 cycles (see para 5.1) Thermal Shock 1 cycle (see para 5.2) 3.5.2 FULLY ASSEMBLED INSERTS AND BEZELS AT LEAST FIVE ORNAMENT ASSEMBLIES WILL BE

    9、TESTED IN THE FOLLOWING SEQUENCE: Water Resistance 144 h (FLTM BI 4-1) Salt Spray Resistance 96 h (FLTM BI 3-1) ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 3 of 5 Copyright 2009, Ford Global Technologies, Inc. Humidity Aging 144 h (ASTM D 2247) Thermal Cycle - C.A.S.S. 5 cycles (see para 5.

    10、1) Thermal Shock 1 cycle (see para 5.2) 3.6 WEATHERING RESISTANCE Expose samples per one of the following: 3.6.1 Carbon - Arc Weatherometer 1600 h (FLTM BO 1-1) 3.6.2 Fluorescent UV - 1600 h Condensation Apparatus (ASTM G-53-84) Operate the apparatus to maintain the following conditions: Cycle - 4 h

    11、 UV exposure at 60 C followed by 4 h condensing humidity at 50 C. 3.6.3 Xenon - Arc Weatherometer 1000 h (ASTM G-26-84) Method 2 Operate the apparatus to maintain the following conditions: Light Cycle Dark Cycle Irradiance 0.55w/m2 - Black Panel Temperature 70 +/- 3 C 38 +/- 2 C Dry Bulb Temperature

    12、 63 +/- 4 C 38 +/- 2 C Relative Humidity 50 +/- 10 % 100 +/- 10 % Conditioning Water 63 +/- 4 C 40 +/- 4 C Following exposure there shall be: No evidence of crazing, checking, warping or other surface degradation. No greater degree of fading, dulling or chalking of subsurface colors than that exhibi

    13、ted by the sample originally approved by the affected Product Engineering office. Blotchy or streaky appearance shall be considered failure. ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 4 of 5 Copyright 2009, Ford Global Technologies, Inc. 3.7 FLORIDA EXPOSURE (For Initial Qualification) Aft

    14、er 12 months minimum exposure at 5 facing south in the Miami, Florida area, there shall be: No evidence of crazing, checking, warping or other surface degradation. No greater degree of fading, dulling, or chalking of subsurface colors than that exhibited by the sample originally approved by the affe

    15、cted Product Engineering office. Blotchy or streaky appearance shall be considered failure. 3.8 SAMPLING Acceptance testing for conformance to Thermal Cycle - Corrosion (para 3.5) and Weathering Resistance (para 3.6) will be run at the frequency specified in Appendix D of Q-101. Suppliers achieving

    16、the Q1 rating will be made exempt from this requirement. 3.9 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved und

    17、er this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notification of the Company, further instructio

    18、ns will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identifi

    19、ed in Restricted Substance Management Standard WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to the Company must have prior approval. Certain materials subcontracted by part suppliers may also require prior approval. These include materials criti

    20、cal to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplie

    21、r shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification. ENGINEERING MATERIAL SPECIFICATION ESB-M15P30-A Page 5 of 5 Copyright 2009, Ford

    22、Global Technologies, Inc. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 THERMAL CYCLE - C.A.S.S. - TEST SEQUENCE 82 +/- 3 C for 2 h 23 +/- 2 C for 1 h -34 +/- 1 C for 2 h 23 +/- 2 C for 1 h 16 h

    23、C.A.S.S. test per FLTM BQ 5-1 1 h rinse and dry then examine. 5.2 THERMAL SHOCK - TEST SEQUENCE Method 1 (refer to FLTM BI 7-3) 4 h water immersion 4 h minimum exposure at -30 +/- 1 C Direct steam blast on scribed X at 45 angle 50 mm - 75 mm from panel for 15 s minimum Method 2 Place one ornament/insert in sufficient deionized water to cover completely. Freeze for four (4) hours at -30 C. Place ice block/insert into large container of hot (50 C) water.


    注意事项

    本文(FORD ESB-M15P30-A-2009 ORNAMENT ASSEMBLY EXTERIOR - ADHESIVE BONDED TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用胶粘剂粘合的装饰组件 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M2P191-A1 FORD .pdf)为本站会员(testyield361)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开