ETSI EN 319 122-2-2016 Electronic Signatures and Infrastructures (ESI) CAdES digital signatures Part 2 Extended CAdES signatures (V1 1 1)《电子签名和基础设施(ESI) CAdMS数字签名 第2部分 扩展的CAdES签名(V.pdf

《ETSI EN 319 122-2-2016 Electronic Signatures and Infrastructures (ESI) CAdES digital signatures Part 2 Extended CAdES signatures (V1 1 1)《电子签名和基础设施(ESI) CAdMS数字签名 第2部分 扩展的CAdES签名(V.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 319 122-2-2016 Electronic Signatures and Infrastructures (ESI) CAdES digital signatures Part 2 Extended CAdES signatures (V1 1 1)《电子签名和基础设施(ESI) CAdMS数字签名 第2部分 扩展的CAdES签名(V.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 319 122-2 V1.1.1 (2016-04) Electronic Signatures and Infrastructures (ESI); CAdES digital signatures; Part 2: Extended CAdES signatures EUROPEAN STANDARD ETSI ETSI EN 319 122-2 V1.1.1 (2016-04) 2 Reference DEN/ESI-0019122-2 Keywords ASN.1, CAdES, electronic signature, security ETSI 650 Rout

2、e des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.

3、org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference i

4、n contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of

5、status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.as

6、px Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ET

7、SI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Mar

8、ks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 319 122-2 V1.1.1 (2016-04) 3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3

9、Introduction 4g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 Additional CAdES levels without references to validation data 7g34.1 Overview 7g34.2 General requirements . 7g34.3 C

10、AdES-E-BES, CAdES-E-EPES, CAdES-E-T and CAdES-E-A built on CAdES-E-T signatures. 8g35 Legacy signatures . 12g3Annex A (normative): CAdES levels with references to validation data 13g3A.1 CAdES-E-C, CAdES-E-X, CAdES-E-X-Long and CAdES-E-X-L signatures . 13g3A.2 CAdES-E-A signatures on CAdES signature

11、s with references to validation data . 17g3History 20g3ETSI ETSI EN 319 122-2 V1.1.1 (2016-04) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly availa

12、ble for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server

13、 (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,

14、 essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Electronic Signatures and Infrastructures (ESI). The present document is part 2 of a multi-part deliverable covering CAdES digital signatures. Full details of the entire series can

15、be found in part 1 1. The present document partly contains an evolved specification of CAdES previously published as ETSI TS 101 733 i.1. National transposition dates Date of adoption of this EN: 1 April 2016 Date of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of ne

16、w National Standard or endorsement of this EN (dop/e): 31 January 2017 Date of withdrawal of any conflicting National Standard (dow): 31 January 2017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot

17、“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction Electronic commerce has emerged as a frequent way of doing busin

18、ess between companies across local, wide area and global networks. Trust in this way of doing business is essential for the success and continued development of electronic commerce. It is therefore important that companies using this electronic means of doing business have suitable security controls

19、 and mechanisms in place to protect their transactions and to ensure trust and confidence with their business partners. In this respect digital signatures are an important security component that can be used to protect information and provide trust in electronic business. The present document is int

20、ended to cover digital signatures supported by PKI and public key certificates, and aims to meet the general requirements of the international community to provide trust and confidence in electronic transactions, including, amongst other, applicable requirements from Regulation (EU) No 910/2014 i.8.

21、 ETSI ETSI EN 319 122-2 V1.1.1 (2016-04) 5 The present document can be used for any transaction between an individual and a company, between two companies, between an individual and a governmental body, etc. The present document is independent of any environment. It can be applied to any environment

22、 e.g. smart cards, GSM SIM cards, special programs for electronic signatures, etc. The present document is part of a rationalized framework of standards (see ETSI TR 119 000 i.2). See ETSI TR 119 100 i.4 for getting guidance on how to use the present document within the aforementioned framework. ETS

23、I ETSI EN 319 122-2 V1.1.1 (2016-04) 6 1 Scope The present document specifies CAdES digital signatures. CAdES signatures are built on CMS signatures i.9, by incorporation of signed and unsigned attributes, which fulfil certain common requirements (such as the long term validity of digital signatures

24、, for instance) in a number of use cases. The present document specifies a number of CAdES signature levels addressing incremental requirements to maintain the validity of the signatures over the long term, in a way that a certain level always addresses all the requirements addressed at levels that

25、are below it. These CAdES extended signatures a higher degree of optionality than the CAdES baseline signatures specified in ETSI EN 319 122-1 1. Procedures for creation, augmentation, and validation of CAdES digital signatures are out of scope and specified in ETSI EN 319 102-1 i.5. Guidance on cre

26、ation, augmentation and validation of CAdES digital signatures including the usage of the different properties is provided in ETSI TR 119 100 i.4. The present document aims at supporting digital signatures in different regulatory frameworks. NOTE: Specifically but not exclusively, CAdES digital sign

27、atures specified in the present document aim at supporting electronic signatures, advanced electronic signatures, qualified electronic signatures, electronic seals, advanced electronic seals, and qualified electronic seals as per Regulation (EU) No 910/2014 i.8. 2 References 2.1 Normative references

28、 References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referen

29、ced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced do

30、cuments are necessary for the application of the present document. 1 ETSI EN 319 122-1: “Electronic Signatures and Infrastructures (ESI); CAdES digital signatures; Part 1: Building blocks and CAdES baseline signatures“. 2.2 Informative references References are either specific (identified by date of

31、 publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid

32、 at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TS 101 733: “Electronic Signatures and Infrastruct

33、ures (ESI); CMS Advanced Electronic Signatures (CAdES)“. i.2 ETSI TR 119 000: “Electronic Signatures and Infrastructures (ESI); The framework for standardization of signatures: overview“. i.3 ETSI TR 119 001: “Electronic Signatures and Infrastructures (ESI); The framework for standardization of sign

34、atures; Definitions and abbreviations“. ETSI ETSI EN 319 122-2 V1.1.1 (2016-04) 7 i.4 ETSI TR 119 100: “Electronic Signatures and Infrastructures (ESI); Business Driven Guidance for Signature Creation and Validation“. i.5 ETSI EN 319 102-1: “Electronic Signatures and Infrastructures (ESI); Procedure

35、s for Creation and Validation of AdES Digital Signatures; Part 1: Creation and Validation“. i.6 ETSI TS 119 172-1: “Electronic Signatures and Infrastructures (ESI); Signature policies; Part 1: Building blocks and table of contents for human readable signature policy documents“. i.7 ETSI TS 119 312:

36、“Electronic Signatures and Infrastructures (ESI); Cryptographic Suites“. i.8 Regulation (EU) No 910/2014 of the European Parliament and of the Council of 23 July 2014 on electronic identification and trust services for electronic transactions in the internal market and repealing Directive 1999/93/EC

37、. i.9 IETF RFC 5652 (2009): “Cryptographic Message Syntax (CMS)“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI TR 119 001 i.3 and ETSI EN 319 122-1 1 apply. 3.2 Abbreviations For the purposes of the present document

38、, the abbreviations given in ETSI TR 119 001 i.3 apply. 4 Additional CAdES levels without references to validation data 4.1 Overview The present document specifies a number of additional levels of CAdES. Each level is created by a combination of attributes defined in ETSI EN 319 122-1 1. NOTE 1: ETS

39、I TR 119 100 i.4 provides a description on the life-cycle of a signature and the rationales on which level is suitable in which situation. NOTE 2: Clause 4.3 defines four CAdES levels namely the CAdES-E-BES, CAdES-E-EPES, CAdES-E-T, and CAdES-E-A built on CAdES-E-T. The normative annex A defines lev

40、els of CAdES signatures incorporating attributes that encapsulate references to validation data and attributes that encapsulate time-stamp tokens on the aforementioned references. NOTE 3: The requirements on the presence and cardinality of the attributes for each CAdES signature level are expressed

41、in tables whose formats and semantics are as specified in clause 6.2.2 of ETSI EN 319 122-1 1. 4.2 General requirements The general CMS syntax shall be as specified in ETSI EN 319 122-1 1, clause 4. The signature shall contain a CMS SignedData, as defined in ETSI EN 319 122-1 1, clause 4.4 and at le

42、ast one SignerInfo (ETSI EN 319 122-1 1, clauses 4.6). The algorithms and key lengths used to generate and augment digital signatures should be as specified in ETSI TS 119 312 i.7. ETSI ETSI EN 319 122-2 V1.1.1 (2016-04) 8 NOTE: Cryptographic suites recommendations defined in ETSI TS 119 312 i.7 can

43、 be superseded by national recommendations. 4.3 CAdES-E-BES, CAdES-E-EPES, CAdES-E-T and CAdES-E-A built on CAdES-E-T signatures CAdES-E-BES, CAdES-E-EPES, CAdES-E-T, and CAdES-E-A built on CAdES-E-T signatures shall be CAdES signatures whose attributes satisfy the requirements specified in the pres

44、ent clause. CAdES-E-EPES signatures are built on CAdES-E-BES signatures by adding one signature-policy-identifier attribute. CAdES-E-T signatures are built on CAdES-E-BES or CAdES-E-EPES signatures by adding one or more signature-time-stamp attributes. CAdES-E-A signatures are built on CAdES-E-T, CA

45、dES-E-C, CAdES-E-X (of Type 1 and of Type 2), CAdES-E-X-Long, and CAdES-E-X-L (of Type 1 and of Type 2) signatures. Annex A specifies CAdES-E-C, CAdES-E-X (of Type 1 and of Type 2), CAdES-E-X-Long, and CAdES-E-X-L (of Type 1 and of Type 2) signatures, and CAdES-E-A built on them. ETSI ETSI EN 319 12

46、2-2 V1.1.1 (2016-04) 9 Table 1: Requirements for CAdES-E-BES, CAdES-E-EPES, CAdES-E-T and CAdES-E-A built on CAdES-E-T Signature fields/Attributes/Services Presence in E-BES level Presence in E-EPES level Presence in E-T level Presence in E-A level Cardinality References Additional requirements and

47、notes content-type shall be present shall be present shall be present shall be present 1 ETSI EN 319 122-1 1, clause 5.1.1 message-digest shall be present shall be present shall be present shall be present 1 ETSI EN 319 122-1 1, clause 5.1.2 Service: protection of signing certificate shall be provid

48、ed shall be provided shall be provided shall be provided 1 ETSI EN 319 122-1 1, clause 5.2.2 SPO: ESS signing-certificate conditioned presence conditioned presence conditioned presence conditioned presence 0 or 1 ETSI EN 319 122-1 1, clause 5.2.2.2 a, e SPO: ESS signing-certificate-v2 conditioned pr

49、esence conditioned presence conditioned presence conditioned presence 0 or 1 ETSI EN 319 122-1 1, clause 5.2.2.3 b, e signing-time may be present may be present may be present may be present 0 or 1 ETSI EN 319 122-1 1, clause 5.2.1 commitment-type-indicationg3 may be present may be present may be present may be present 0 or 1 ETSI EN 319 122-1 1, clause 5.2.3 content-hints may be present may be present may be present may be present 0 or 1 ETSI EN 319 122-1 1, clause 5.2.4.1 mime-type may be present